Commit aeceecd4 authored by Linus Walleij's avatar Linus Walleij
Browse files

ARM: dts: ux500: Fix up TVK R3 sensors 



The TVK1281618 R3 sensors are different from the R2 board,
some incorrectness is fixed and some new sensors added, we
also rename the nodes appropriately with accelerometer@
etc.

Signed-off-by: default avatarLinus Walleij <linus.walleij@linaro.org>
parent 8d67f4f6

arch/arm/boot/dts/ste-href-tvk1281618-r3.dtsi

+50 −23
Original line number Diff line number Diff line
@@ -8,37 +8,43 @@ 
/ {

	soc {

		i2c@80128000 {

			/* Marked:

			 * 129

			 * M35

			 * L3GD20

			 */

			l3gd20@6a {

				/* Gyroscope */

				compatible = "st,l3gd20";

				status = "disabled";

			accelerometer@19 {

				compatible = "st,lsm303dlhc-accel";

				st,drdy-int-pin = <1>;

				drive-open-drain;

				reg = <0x6a>; // 0x6a or 0x6b

				reg = <0x19>;

				vdd-supply = <&ab8500_ldo_aux1_reg>;

				vddio-supply = <&db8500_vsmps2_reg>;

				interrupt-parent = <&gpio2>;

				interrupts = <18 IRQ_TYPE_EDGE_RISING>,

					     <19 IRQ_TYPE_EDGE_RISING>;

				pinctrl-names = "default";

				pinctrl-0 = <&accel_tvk_mode>;

			};

			/*

			 * Marked:

			 * 2122

			 * C3H

			 * DQEEE

			 * LIS3DH?

			 */

			lis3dh@18 {

				/* Accelerometer */

				compatible = "st,lis3dh-accel";

			magnetometer@1e {

				compatible = "st,lsm303dlm-magn";

				st,drdy-int-pin = <1>;

				reg = <0x18>;

				reg = <0x1e>;

				vdd-supply = <&ab8500_ldo_aux1_reg>;

				vddio-supply = <&db8500_vsmps2_reg>;

				// This interrupt is not properly working with the driver

				// interrupt-parent = <&gpio1>;

				// interrupts = <0 IRQ_TYPE_EDGE_RISING>;

				pinctrl-names = "default";

				pinctrl-0 = <&accel_tvk_mode>;

				pinctrl-0 = <&magn_tvk_mode>;

			};

			gyroscope@68 {

				/* Gyroscope */

				compatible = "st,l3g4200d-gyro";

				reg = <0x68>;

				vdd-supply = <&ab8500_ldo_aux1_reg>;

				vddio-supply = <&db8500_vsmps2_reg>;

			};

			pressure@5c {

				/* Barometer/pressure sensor */

				compatible = "st,lps001wp-press";

				reg = <0x5c>;

				vdd-supply = <&ab8500_ldo_aux1_reg>;

				vddio-supply = <&db8500_vsmps2_reg>;

			};

		};
@@ -54,5 +60,26 @@ panel { 
				};

			};

		};



		pinctrl {

			accelerometer {

				accel_tvk_mode: accel_tvk {

					/* Accelerometer interrupt lines 1 & 2 */

					tvk_cfg {

						pins = "GPIO82_C1", "GPIO83_D3";

						ste,config = <&gpio_in_pd>;

					};

				};

			};

			magnetometer {

				magn_tvk_mode: magn_tvk {

					/* GPIO 32 used for DRDY, pull this down */

					tvk_cfg {

						pins = "GPIO32_V2";

						ste,config = <&gpio_in_pd>;

					};

				};

			};

		};

	};

};