Merge tag 'drm-next-2019-07-16' of git://anongit.freedesktop.org/drm/drm

Pull drm updates from Dave Airlie:
 "The biggest thing in this is the AMD Navi GPU support, this again
  contains a bunch of header files that are large. These are the new AMD
  RX5700 GPUs that just recently became available.

  New drivers:
   - ST-Ericsson MCDE driver
   - Ingenic JZ47xx SoC

  UAPI change:
   - HDR source metadata property

  Core:
   - HDR inforframes and EDID parsing
   - drm hdmi infoframe unpacking
   - remove prime sg_table caching into dma-buf
   - New gem vram helpers to reduce driver code
   - Lots of drmP.h removal
   - reservation fencing fix
   - documentation updates
   - drm_fb_helper_connector removed
   - mode name command handler rewrite

  fbcon:
   - Remove the fbcon notifiers

  ttm:
   - forward progress fixes

  dma-buf:
   - make mmap call optional
   - debugfs refcount fixes
   - dma-fence free with pending signals fix
   - each dma-buf gets an inode

  Panels:
   - Lots of additional panel bindings

  amdgpu:
   - initial navi10 support
   - avoid hw reset
   - HDR metadata support
   - new thermal sensors for vega asics
   - RAS fixes
   - use HMM rather than MMU notifier
   - xgmi topology via kfd
   - SR-IOV fixes
   - driver reload fixes
   - DC use a core bpc attribute
   - Aux fixes for DC
   - Bandwidth calc updates for DC
   - Clock handling refactor
   - kfd VEGAM support

  vmwgfx:
   - Coherent memory support changes

  i915:
   - HDR Support
   - HDMI i2c link
   - Icelake multi-segmented gamma support
   - GuC firmware update
   - Mule Creek Canyon PCH support for EHL
   - EHL platform updtes
   - move i915.alpha_support to i915.force_probe
   - runtime PM refactoring
   - VBT parsing refactoring
   - DSI fixes
   - struct mutex dependency reduction
   - GEM code reorg

  mali-dp:
   - Komeda driver features

  msm:
   - dsi vs EPROBE_DEFER fixes
   - msm8998 snapdragon 835 support
   - a540 gpu support
   - mdp5 and dpu interconnect support

  exynos:
   - drmP.h removal

  tegra:
   - misc fixes

  tda998x:
   - audio support improvements
   - pixel repeated mode support
   - quantisation range handling corrections
   - HDMI vendor info fix

  armada:
   - interlace support fix
   - overlay/video plane register handling refactor
   - add gamma support

  rockchip:
   - RX3328 support

  panfrost:
   - expose perf counters via hidden ioctls

  vkms:
   - enumerate CRC sources list

  ast:
   - rework BO handling

  mgag200:
   - rework BO handling

  dw-hdmi:
   - suspend/resume support

  rcar-du:
   - R8A774A1 Soc Support
   - LVDS dual-link mode support
   - Additional formats
   - Misc fixes

  omapdrm:
   - DSI command mode display support

  stm
   - fb modifier support
   - runtime PM support

  sun4i:
   - use vmap ops

  vc4:
   - binner bo binding rework

  v3d:
   - compute shader support
   - resync/sync fixes
   - job management refactoring

  lima:
   - NULL pointer in irq handler fix
   - scheduler default timeout

  virtio:
   - fence seqno support
   - trace events

  bochs:
   - misc fixes

  tc458767:
   - IRQ/HDP handling

  sii902x:
   - HDMI audio support

  atmel-hlcdc:
   - misc fixes

  meson:
   - zpos support"

* tag 'drm-next-2019-07-16' of git://anongit.freedesktop.org/drm/drm: (1815 commits)
  Revert "Merge branch 'vmwgfx-next' of git://people.freedesktop.org/~thomash/linux into drm-next"
  Revert "mm: adjust apply_to_pfn_range interface for dropped token."
  mm: adjust apply_to_pfn_range interface for dropped token.
  drm/amdgpu/navi10: add uclk activity sensor
  drm/amdgpu: properly guard the generic discovery code
  drm/amdgpu: add missing documentation on new module parameters
  drm/amdgpu: don't invalidate caches in RELEASE_MEM, only do the writeback
  drm/amd/display: avoid 64-bit division
  drm/amdgpu/psp11: simplify the ucode register logic
  drm/amdgpu: properly guard DC support in navi code
  drm/amd/powerplay: vega20: fix uninitialized variable use
  drm/amd/display: dcn20: include linux/delay.h
  amdgpu: make pmu support optional
  drm/amd/powerplay: Zero initialize current_rpm in vega20_get_fan_speed_percent
  drm/amd/powerplay: Zero initialize freq in smu_v11_0_get_current_clk_freq
  drm/amd/powerplay: Use memset to initialize metrics structs
  drm/amdgpu/mes10.1: Fix header guard
  drm/amd/powerplay: add temperature sensor support for navi10
  drm/amdgpu: fix scheduler timeout calc
  drm/amdgpu: Prepare for hmm_range_register API change (v2)
  ...

Documentation/devicetree/bindings/display/allwinner,sun6i-a31-mipi-dsi.yaml

+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/allwinner,sun6i-a31-mipi-dsi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Allwinner A31 MIPI-DSI Controller Device Tree Bindings
+
+maintainers:
+  - Chen-Yu Tsai <wens@csie.org>
+  - Maxime Ripard <maxime.ripard@bootlin.com>
+
+properties:
+  "#address-cells": true
+  "#size-cells": true
+
+  compatible:
+    const: allwinner,sun6i-a31-mipi-dsi
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: Bus Clock
+      - description: Module Clock
+
+  clock-names:
+    items:
+      - const: bus
+      - const: mod
+
+  resets:
+    maxItems: 1
+
+  phys:
+    maxItems: 1
+
+  phy-names:
+    const: dphy
+
+  port:
+    type: object
+    description:
+      A port node with endpoint definitions as defined in
+      Documentation/devicetree/bindings/media/video-interfaces.txt. That
+      port should be the input endpoint, usually coming from the
+      associated TCON.
+
+patternProperties:
+  "^panel@[0-9]+$": true
+
+required:
+  - "#address-cells"
+  - "#size-cells"
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+  - phys
+  - phy-names
+  - resets
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+    dsi0: dsi@1ca0000 {
+        compatible = "allwinner,sun6i-a31-mipi-dsi";
+        reg = <0x01ca0000 0x1000>;
+        interrupts = <0 89 4>;
+        clocks = <&ccu 23>, <&ccu 96>;
+        clock-names = "bus", "mod";
+        resets = <&ccu 4>;
+        phys = <&dphy0>;
+        phy-names = "dphy";
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        panel@0 {
+                compatible = "bananapi,lhr050h41", "ilitek,ili9881c";
+                reg = <0>;
+                power-gpios = <&pio 1 7 0>; /* PB07 */
+                reset-gpios = <&r_pio 0 5 1>; /* PL05 */
+                backlight = <&pwm_bl>;
+        };
+
+        port {
+            dsi0_in_tcon0: endpoint {
+                remote-endpoint = <&tcon0_out_dsi0>;
+            };
+        };
+    };
+
+...

Documentation/devicetree/bindings/display/arm,komeda.txt

@@ -7,10 +7,13 @@ Required properties:
 - clocks: A list of phandle + clock-specifier pairs, one for each entry
     in 'clock-names'
 - clock-names: A list of clock names. It should contain:
-      - "mclk": for the main processor clock
-      - "pclk": for the APB interface clock
+      - "aclk": for the main processor clock
 - #address-cells: Must be 1
 - #size-cells: Must be 0
+- iommus: configure the stream id to IOMMU, Must be configured if want to
+    enable iommu in display. for how to configure this node please reference
+        devicetree/bindings/iommu/arm,smmu-v3.txt,
+        devicetree/bindings/iommu/iommu.txt
 
 Required properties for sub-node: pipeline@nq
 Each device contains one or two pipeline sub-nodes (at least one), each
@@ -20,7 +23,6 @@ pipeline node should provide properties:
     in 'clock-names'
 - clock-names: should contain:
       - "pxclk": pixel clock
-      - "aclk": AXI interface clock
 
 - port: each pipeline connect to an encoder input port. The connection is
     modeled using the OF graph bindings specified in
@@ -42,12 +44,15 @@ Example:
 		compatible = "arm,mali-d71";
 		reg = <0xc00000 0x20000>;
 		interrupts = <0 168 4>;
-		clocks = <&dpu_mclk>, <&dpu_aclk>;
-		clock-names = "mclk", "pclk";
+		clocks = <&dpu_aclk>;
+		clock-names = "aclk";
+		iommus = <&smmu 0>, <&smmu 1>, <&smmu 2>, <&smmu 3>,
+			<&smmu 4>, <&smmu 5>, <&smmu 6>, <&smmu 7>,
+			<&smmu 8>, <&smmu 9>;
 
 		dp0_pipe0: pipeline@0 {
-			clocks = <&fpgaosc2>, <&dpu_aclk>;
-			clock-names = "pxclk", "aclk";
+			clocks = <&fpgaosc2>;
+			clock-names = "pxclk";
 			reg = <0>;
 
 			port {
@@ -58,8 +63,8 @@ Example:
 		};
 
 		dp0_pipe1: pipeline@1 {
-			clocks = <&fpgaosc2>, <&dpu_aclk>;
-			clock-names = "pxclk", "aclk";
+			clocks = <&fpgaosc2>;
+			clock-names = "pxclk";
 			reg = <1>;
 
 			port {

Documentation/devicetree/bindings/display/bridge/renesas,lvds.txt

@@ -9,6 +9,7 @@ Required properties:
 - compatible : Shall contain one of
   - "renesas,r8a7743-lvds" for R8A7743 (RZ/G1M) compatible LVDS encoders
   - "renesas,r8a7744-lvds" for R8A7744 (RZ/G1N) compatible LVDS encoders
+  - "renesas,r8a774a1-lvds" for R8A774A1 (RZ/G2M) compatible LVDS encoders
   - "renesas,r8a774c0-lvds" for R8A774C0 (RZ/G2E) compatible LVDS encoders
   - "renesas,r8a7790-lvds" for R8A7790 (R-Car H2) compatible LVDS encoders
   - "renesas,r8a7791-lvds" for R8A7791 (R-Car M2-W) compatible LVDS encoders
@@ -45,14 +46,24 @@ OF graph bindings specified in Documentation/devicetree/bindings/graph.txt.
 
 Each port shall have a single endpoint.
 
+Optional properties:
+
+- renesas,companion : phandle to the companion LVDS encoder. This property is
+  mandatory for the first LVDS encoder on D3 and E3 SoCs, and shall point to
+  the second encoder to be used as a companion in dual-link mode. It shall not
+  be set for any other LVDS encoder.
+
 
 Example:
 
 	lvds0: lvds@feb90000 {
-		compatible = "renesas,r8a7790-lvds";
-		reg = <0 0xfeb90000 0 0x1c>;
-		clocks = <&cpg CPG_MOD 726>;
-		resets = <&cpg 726>;
+		compatible = "renesas,r8a77990-lvds";
+		reg = <0 0xfeb90000 0 0x20>;
+		clocks = <&cpg CPG_MOD 727>;
+		power-domains = <&sysc R8A77990_PD_ALWAYS_ON>;
+		resets = <&cpg 727>;
+
+		renesas,companion = <&lvds1>;
 
 		ports {
 			#address-cells = <1>;

Documentation/devicetree/bindings/display/bridge/sii902x.txt

@@ -5,10 +5,44 @@ Required properties:
 	- reg: i2c address of the bridge
 
 Optional properties:
-	- interrupts: describe the interrupt line used to inform the host 
+	- interrupts: describe the interrupt line used to inform the host
 	  about hotplug events.
 	- reset-gpios: OF device-tree gpio specification for RST_N pin.
 
+	HDMI audio properties:
+	- #sound-dai-cells: <0> or <1>. <0> if only i2s or spdif pin
+	   is wired, <1> if the both are wired. HDMI audio is
+	   configured only if this property is found.
+	- sil,i2s-data-lanes: Array of up to 4 integers with values of 0-3
+	   Each integer indicates which i2s pin is connected to which
+	   audio fifo. The first integer selects i2s audio pin for the
+	   first audio fifo#0 (HDMI channels 1&2), second for fifo#1
+	   (HDMI channels 3&4), and so on. There is 4 fifos and 4 i2s
+	   pins (SD0 - SD3). Any i2s pin can be connected to any fifo,
+	   but there can be no gaps. E.g. an i2s pin must be mapped to
+	   fifo#0 and fifo#1 before mapping a channel to fifo#2. Default
+	   value is <0>, describing SD0 pin beiging routed to hdmi audio
+	   fifo #0.
+	- clocks: phandle and clock specifier for each clock listed in
+           the clock-names property
+	- clock-names: "mclk"
+	   Describes SII902x MCLK input. MCLK is used to produce
+	   HDMI audio CTS values. This property is required if
+	   "#sound-dai-cells"-property is present. This property follows
+	   Documentation/devicetree/bindings/clock/clock-bindings.txt
+	   consumer binding.
+
+	If HDMI audio is configured the sii902x device becomes an I2S
+	and/or spdif audio codec component (e.g a digital audio sink),
+	that can be used in configuring a full audio devices with
+	simple-card or audio-graph-card binding. See their binding
+	documents on how to describe the way the sii902x device is
+	connected to the rest of the audio system:
+	Documentation/devicetree/bindings/sound/simple-card.txt
+	Documentation/devicetree/bindings/sound/audio-graph-card.txt
+	Note: In case of the audio-graph-card binding the used port
+	index should be 3.
+
 Optional subnodes:
 	- video input: this subnode can contain a video input port node
 	  to connect the bridge to a display controller output (See this
@@ -21,6 +55,12 @@ Example:
 		compatible = "sil,sii9022";
 		reg = <0x39>;
 		reset-gpios = <&pioA 1 0>;
+
+		#sound-dai-cells = <0>;
+		sil,i2s-data-lanes = < 0 1 2 >;
+		clocks = <&mclk>;
+		clock-names = "mclk";
+
 		ports {
 			#address-cells = <1>;
 			#size-cells = <0>;

Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.txt

@@ -28,6 +28,12 @@ Optional video port nodes:
 - port@1: Second LVDS input port
 - port@3: Second digital CMOS/TTL parallel output
 
+The device can operate in single-link mode or dual-link mode. In single-link
+mode, all pixels are received on port@0, and port@1 shall not contain any
+endpoint. In dual-link mode, even-numbered pixels are received on port@0 and
+odd-numbered pixels on port@1, and both port@0 and port@1 shall contain
+endpoints.
+
 Example:
 --------
 

Documentation/devicetree/bindings/display/bridge/toshiba,tc358767.txt

@@ -12,6 +12,7 @@ Optional properties:
                    (active high shutdown input)
  - reset-gpios: OF device-tree gpio specification for RSTX pin
                 (active low system reset)
+ - toshiba,hpd-pin: TC358767 GPIO pin number to which HPD is connected to (0 or 1)
  - ports: the ports node can contain video interface port nodes to connect
    to a DPI/DSI source and to an eDP/DP sink according to [1][2]:
     - port@0: DSI input port

Documentation/devicetree/bindings/display/ingenic,lcd.txt

+Ingenic JZ47xx LCD driver
+
+Required properties:
+- compatible: one of:
+  * ingenic,jz4740-lcd
+  * ingenic,jz4725b-lcd
+- reg: LCD registers location and length
+- clocks: LCD pixclock and device clock specifiers.
+	   The device clock is only required on the JZ4740.
+- clock-names: "lcd_pclk" and "lcd"
+- interrupts: Specifies the interrupt line the LCD controller is connected to.
+
+Example:
+
+panel {
+	compatible = "sharp,ls020b1dd01d";
+
+	backlight = <&backlight>;
+	power-supply = <&vcc>;
+
+	port {
+		panel_input: endpoint {
+			remote-endpoint = <&panel_output>;
+		};
+	};
+};
+
+
+lcd: lcd-controller@13050000 {
+	compatible = "ingenic,jz4725b-lcd";
+	reg = <0x13050000 0x1000>;
+
+	interrupt-parent = <&intc>;
+	interrupts = <31>;
+
+	clocks = <&cgu JZ4725B_CLK_LCD>;
+	clock-names = "lcd";
+
+	port {
+		panel_output: endpoint {
+			remote-endpoint = <&panel_input>;
+		};
+	};
+};

Documentation/devicetree/bindings/display/msm/dpu.txt

@@ -28,6 +28,11 @@ Required properties:
 - #address-cells: number of address cells for the MDSS children. Should be 1.
 - #size-cells: Should be 1.
 - ranges: parent bus address space is the same as the child bus address space.
+- interconnects : interconnect path specifier for MDSS according to
+  Documentation/devicetree/bindings/interconnect/interconnect.txt. Should be
+  2 paths corresponding to 2 AXI ports.
+- interconnect-names : MDSS will have 2 port names to differentiate between the
+  2 interconnect paths defined with interconnect specifier.
 
 Optional properties:
 - assigned-clocks: list of clock specifiers for clocks needing rate assignment
@@ -86,6 +91,11 @@ Example:
 		interrupt-controller;
 		#interrupt-cells = <1>;
 
+		interconnects = <&rsc_hlos MASTER_MDP0 &rsc_hlos SLAVE_EBI1>,
+				<&rsc_hlos MASTER_MDP1 &rsc_hlos SLAVE_EBI1>;
+
+		interconnect-names = "mdp0-mem", "mdp1-mem";
+
 		iommus = <&apps_iommu 0>;
 
 		#address-cells = <2>;

Documentation/devicetree/bindings/display/msm/dsi.txt

@@ -88,6 +88,7 @@ Required properties:
   * "qcom,dsi-phy-28nm-8960"
   * "qcom,dsi-phy-14nm"
   * "qcom,dsi-phy-10nm"
+  * "qcom,dsi-phy-10nm-8998"
 - reg: Physical base address and length of the registers of PLL, PHY. Some
   revisions require the PHY regulator base address, whereas others require the
   PHY lane base address. See below for each PHY revision.

Documentation/devicetree/bindings/display/panel/armadeus,st0700-adapt.txt

+Armadeus ST0700 Adapt. A Santek ST0700I5Y-RBSLW 7.0" WVGA (800x480) TFT with
+an adapter board.
+
+Required properties:
+- compatible: "armadeus,st0700-adapt"
+- power-supply: see panel-common.txt
+
+Optional properties:
+- backlight: see panel-common.txt

Documentation/devicetree/bindings/display/panel/edt,et-series.txt

@@ -6,6 +6,22 @@ Display bindings for EDT Display Technology Corp. Displays which are
 compatible with the simple-panel binding, which is specified in
 simple-panel.txt
 
+3,5" QVGA TFT Panels
+--------------------
++-----------------+---------------------+-------------------------------------+
+| Identifier      | compatbile          | description                         |
++=================+=====================+=====================================+
+| ET035012DM6     | edt,et035012dm6     | 3.5" QVGA TFT LCD panel             |
++-----------------+---------------------+-------------------------------------+
+
+4,3" WVGA TFT Panels
+--------------------
+
++-----------------+---------------------+-------------------------------------+
+| Identifier      | compatbile          | description                         |
++=================+=====================+=====================================+
+| ETM0430G0DH6    | edt,etm0430g0dh6    | 480x272 TFT Display                 |
++-----------------+---------------------+-------------------------------------+
 
 5,7" WVGA TFT Panels
 --------------------

Documentation/devicetree/bindings/display/panel/evervision,vgg804821.txt

+Evervision Electronics Co. Ltd. VGG804821 5.0" WVGA TFT LCD Panel
+
+Required properties:
+- compatible: should be "evervision,vgg804821"
+- power-supply: See simple-panel.txt
+
+Optional properties:
+- backlight: See simple-panel.txt
+- enable-gpios: See simple-panel.txt
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.

Documentation/devicetree/bindings/display/panel/friendlyarm,hd702e.txt

+FriendlyELEC HD702E 800x1280 LCD panel
+
+HD702E lcd is FriendlyELEC developed eDP LCD panel with 800x1280
+resolution. It has built in Goodix, GT9271 captive touchscreen
+with backlight adjustable via PWM.
+
+Required properties:
+- compatible: should be "friendlyarm,hd702e"
+- power-supply: regulator to provide the supply voltage
+
+Optional properties:
+- backlight: phandle of the backlight device attached to the panel
+
+Optional nodes:
+- Video port for LCD panel input.
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
+
+Example:
+
+	panel {
+		compatible ="friendlyarm,hd702e", "simple-panel";
+		backlight = <&backlight>;
+		power-supply = <&vcc3v3_sys>;
+
+		port {
+			panel_in_edp: endpoint {
+				remote-endpoint = <&edp_out_panel>;
+			};
+		};
+	};

Documentation/devicetree/bindings/display/panel/koe,tx14d24vm1bpa.txt

+Kaohsiung Opto-Electronics Inc. 5.7" QVGA (320 x 240) TFT LCD panel
+
+Required properties:
+- compatible: should be "koe,tx14d24vm1bpa"
+- backlight: phandle of the backlight device attached to the panel
+- power-supply: single regulator to provide the supply voltage
+
+Required nodes:
+- port: Parallel port mapping to connect this display
+
+This panel needs single power supply voltage. Its backlight is conntrolled
+via PWM signal.
+
+Example:
+--------
+
+Example device-tree definition when connected to iMX53 based board
+
+	lcd_panel: lcd-panel {
+		compatible = "koe,tx14d24vm1bpa";
+		backlight = <&backlight_lcd>;
+		power-supply = <&reg_3v3>;
+
+		port {
+			lcd_panel_in: endpoint {
+				remote-endpoint = <&lcd_display_out>;
+			};
+		};
+	};
+
+Then one needs to extend the dispX node:
+
+	lcd_display: disp1 {
+
+		port@1 {
+			reg = <1>;
+
+			lcd_display_out: endpoint {
+				remote-endpoint = <&lcd_panel_in>;
+			};
+		};
+	};

Documentation/devicetree/bindings/display/panel/osddisplays,osd101t2045-53ts.txt

+One Stop Displays OSD101T2045-53TS 10.1" 1920x1200 panel
+
+Required properties:
+- compatible: should be "osddisplays,osd101t2045-53ts"
+- power-supply: as specified in the base binding
+
+Optional properties:
+- backlight: as specified in the base binding
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.

Documentation/devicetree/bindings/display/panel/osddisplays,osd101t2587-53ts.txt

+One Stop Displays OSD101T2587-53TS 10.1" 1920x1200 panel
+
+The panel is similar to OSD101T2045-53TS, but it needs additional
+MIPI_DSI_TURN_ON_PERIPHERAL message from the host.
+
+Required properties:
+- compatible: should be "osddisplays,osd101t2587-53ts"
+- power-supply: as specified in the base binding
+
+Optional properties:
+- backlight: as specified in the base binding
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.

Documentation/devicetree/bindings/display/panel/samsung,s6e63m0.txt

+Samsung s6e63m0 AMOLED LCD panel
+
+Required properties:
+  - compatible: "samsung,s6e63m0"
+  - reset-gpios: GPIO spec for reset pin
+  - vdd3-supply: VDD regulator
+  - vci-supply: VCI regulator
+
+The panel must obey rules for SPI slave device specified in document [1].
+
+The device node can contain one 'port' child node with one child
+'endpoint' node, according to the bindings defined in [2]. This
+node should describe panel's video bus.
+
+[1]: Documentation/devicetree/bindings/spi/spi-bus.txt
+[2]: Documentation/devicetree/bindings/media/video-interfaces.txt
+
+Example:
+
+		s6e63m0: display@0 {
+			compatible = "samsung,s6e63m0";
+			reg = <0>;
+			reset-gpio = <&mp05 5 1>;
+			vdd3-supply = <&ldo12_reg>;
+			vci-supply = <&ldo11_reg>;
+			spi-max-frequency = <1200000>;
+
+			port {
+				lcd_ep: endpoint {
+					remote-endpoint = <&fimd_ep>;
+				};
+			};
+		};

Documentation/devicetree/bindings/display/panel/tfc,s9700rtwv43tr-01b.txt

+TFC S9700RTWV43TR-01B 7" Three Five Corp 800x480 LCD panel with
+resistive touch
+
+The panel is found on TI AM335x-evm.
+
+Required properties:
+- compatible: should be "tfc,s9700rtwv43tr-01b"
+- power-supply: See panel-common.txt
+
+Optional properties:
+- enable-gpios: GPIO pin to enable or disable the panel, if there is one
+- backlight: phandle of the backlight device attached to the panel
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.

Documentation/devicetree/bindings/display/panel/vl050_8048nt_c01.txt

+VXT 800x480 color TFT LCD panel
+
+Required properties:
+- compatible: should be "vxt,vl050-8048nt-c01"
+- power-supply: as specified in the base binding
+
+Optional properties:
+- backlight: as specified in the base binding
+- enable-gpios: as specified in the base binding
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.

Documentation/devicetree/bindings/display/renesas,du.txt

@@ -7,6 +7,7 @@ Required Properties:
     - "renesas,du-r8a7744" for R8A7744 (RZ/G1N) compatible DU
     - "renesas,du-r8a7745" for R8A7745 (RZ/G1E) compatible DU
     - "renesas,du-r8a77470" for R8A77470 (RZ/G1C) compatible DU
+    - "renesas,du-r8a774a1" for R8A774A1 (RZ/G2M) compatible DU
     - "renesas,du-r8a774c0" for R8A774C0 (RZ/G2E) compatible DU
     - "renesas,du-r8a7779" for R8A7779 (R-Car H1) compatible DU
     - "renesas,du-r8a7790" for R8A7790 (R-Car H2) compatible DU
@@ -58,6 +59,7 @@ corresponding to each DU output.
  R8A7744 (RZ/G1N)       DPAD 0         LVDS 0         -              -
  R8A7745 (RZ/G1E)       DPAD 0         DPAD 1         -              -
  R8A77470 (RZ/G1C)      DPAD 0         DPAD 1         LVDS 0         -
+ R8A774A1 (RZ/G2M)      DPAD 0         HDMI 0         LVDS 0         -
  R8A774C0 (RZ/G2E)      DPAD 0         LVDS 0         LVDS 1         -
  R8A7779 (R-Car H1)     DPAD 0         DPAD 1         -              -
  R8A7790 (R-Car H2)     DPAD 0         LVDS 0         LVDS 1         -