The '#mbox-cells' property is added to all the OMAP mailbox
nodes. This property is mandatory with the new mailbox framework.

Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add the interrupts property to all the 13 mailbox nodes in
DRA7xx. The interrupts property information added is inline
with the expected values with the DRA7xx crossbar driver,
and is common to both DRA74x and DRA72x SoCs.

Do note that the mailbox 1 is only capable of generating out
3 interrupts, while all the remaining mailboxes have 4
interrupts each.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Looks like we have some GPMC NAND timings missing device
width. This fixes "gpmc_cs_program_settings: invalid width 0!"
errors during boot.

Signed-off-by: Tony Lindgren <tony@atomide.com>

With the GPMC warnings now enabled, I noticed the LAN9220 timings
can overflow the GPMC registers with 200MHz L3 speed. Earlier we
were just skipping the bad timings and would continue with the
bootloader timings. Now we no longer allow to continue with bad
timings as we have the timings in the .dts files.

We could start using the GPMC clock divider, but let's instead
use the u-boot timings that are known to be working and a bit
faster. These are basically the u-boot NET_GPMC_CONFIG[1-6]
defines deciphered. Except that we don't set gpmc,burst-length
as that's only partially configured and does not seem to work
if fully enabled.

[tony@atomide.com: updated to remove gpmc,burst-length]
Signed-off-by: Tony Lindgren <tony@atomide.com>

The four port serial port on the zoom debug board uses a TL16CP754C
with a single interrupt and GPMC chip select. The serial ports each
use a 8 bytes for IO registers, and are 256 bytes apart on the GPMC
line.

Let's add timings for all four ports so we can remove the GPMC
workarounds for using bootloader timings.

Not caused by this patch, but looks like u-boot only properly
initializes the fifo on the first serial port. Currently the other
ports produce garbage at least with my version of u-boot. I suspect
that TL16CP754C needs non-standard initialization added to 8250
driver to properly fix this issue.

Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Let's use the bootloader values except for the partially configured
wait-pin that does not seem to work.

Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The GPMC binding is obviously very confusing as the values
are all over the place. People seem to confuse the GPMC partition
size for the chip select, and the device IO size within the GPMC
partition easily.

The ranges entry contains the GPMC partition size. And the
reg entry contains the size of the IO registers of the
device connected to the GPMC.

Let's fix the issue according to the following table:

Device          GPMC partition size     Device IO size
connected       in the ranges entry     in the reg entry

NAND            0x01000000 (16MB)       4
16550           0x01000000 (16MB)       8
smc91x          0x01000000 (16MB)       0xf
smc911x         0x01000000 (16MB)       0xff
OneNAND         0x01000000 (16MB)       0x20000 (128KB)
16MB NOR        0x01000000 (16MB)       0x01000000 (16MB)
32MB NOR        0x02000000 (32MB)       0x02000000 (32MB)
64MB NOR        0x04000000 (64MB)       0x04000000 (64MB)
128MB NOR       0x08000000 (128MB)      0x08000000 (128MB)
256MB NOR       0x10000000 (256MB)      0x10000000 (256MB)

Let's also add comments to the fixed entries while at it.

Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Apparently some versions of nolo don't mux the all the necessary GPMC
pins for the smc91x probe to work properly. Let's fix this issue
by adding mux support for GPMC to the kernel.

Note that GPMC clk needs input enabled for OnenNAND to work.

Cc: Kevin Hilman <khilman@kernel.org>
Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Commit 78b81f46 ("ARM: dts: imx28-evk: Run I2C0 at 400kHz") caused issues
when doing the following sequence in loop:

- Boot the kernel
- Perform audio playback
- Reboot the system via 'reboot' command

In many times the audio card cannot be probed, which causes playback to fail.

After restoring to the original i2c0 frequency of 100kHz there is no such
problem anymore.

This reverts commit 78b81f46.

Cc: <stable@vger.kernel.org> # 3.16+
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Fix a typo error, the "emi" names refer to the eim clocks.

The change fixes typo in EIM and EIM_SLOW pre-output dividers and
selectors clock names. Notably EIM_SLOW clock itself is named correctly.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
[vladimir_zapolskiy@mentor.com: ported to v3.17]
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

With 48-bit VA space, the 64K page configuration uses 3 levels instead
of 2 and PUD_SIZE != PMD_SIZE. Since with 64K pages we only cover
PMD_SIZE with the initial swapper_pg_dir populated in head.S, the
memblock current_limit needs to be set accordingly in map_mem() to avoid
allocating unmapped memory. The memblock current_limit is progressively
increased as more blocks are mapped.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

It is not sufficient to only implement get_user_pages_fast(), you
must also implement the atomic version __get_user_pages_fast()
otherwise you end up using the weak symbol fallback implementation
which simply returns zero.

This is dangerous, because it causes the futex code to loop forever
if transparent hugepages are supported (see get_futex_key()).

Signed-off-by: David S. Miller <davem@davemloft.net>

Meelis Roos reported that kernels built with gcc-4.9 do not boot, we
eventually narrowed this down to only impacting machines using
UltraSPARC-III and derivitive cpus.

The crash happens right when the first user process is spawned:

[   54.451346] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000004
[   54.451346]
[   54.571516] CPU: 1 PID: 1 Comm: init Not tainted 3.16.0-rc2-00211-gd7933ab #96
[   54.666431] Call Trace:
[   54.698453]  [0000000000762f8c] panic+0xb0/0x224
[   54.759071]  [000000000045cf68] do_exit+0x948/0x960
[   54.823123]  [000000000042cbc0] fault_in_user_windows+0xe0/0x100
[   54.902036]  [0000000000404ad0] __handle_user_windows+0x0/0x10
[   54.978662] Press Stop-A (L1-A) to return to the boot prom
[   55.050713] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000004

Further investigation showed that compiling only per_cpu_patch() with
an older compiler fixes the boot.

Detailed analysis showed that the function is not being miscompiled by
gcc-4.9, but it is using a different register allocation ordering.

With the gcc-4.9 compiled function, something during the code patching
causes some of the %i* input registers to get corrupted.  Perhaps
we have a TLB miss path into the firmware that is deep enough to
cause a register window spill and subsequent restore when we get
back from the TLB miss trap.

Let's plug this up by doing two things:

1) Stop using the firmware stack for client interface calls into
   the firmware.  Just use the kernel's stack.

2) As soon as we can, call into a new function "start_early_boot()"
   to put a one-register-window buffer between the firmware's
   deepest stack frame and the top-most initial kernel one.

Reported-by: Meelis Roos <mroos@linux.ee>
Tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>

When user asks to turn off ASLR by writing "0" to
/proc/sys/kernel/randomize_va_space there should not be
any randomization to mmap base, stack, VDSO, libs, text and heap

Currently arm64 violates this behavior by randomising text.
Fix this by defining a constant ELF_ET_DYN_BASE. The randomisation of
mm->mmap_base is done by setup_new_exec -> arch_pick_mmap_layout ->
mmap_base -> mmap_rnd.

Signed-off-by: Arun Chandran <achandran@mvista.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

This isn't a module and shouldn't be one.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Even after the recent fix, the assertion on paging_tmpl.h is triggered.
Apparently, the assertion wants to check that the PAE is always set on
long-mode, but does it in incorrect way.  Note that the assertion is not
enabled unless the code is debugged by defining MMU_DEBUG.

Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

The decode phase of the x86 emulator assumes that every instruction with the
ModRM flag, and which can be used with RIP-relative addressing, has either
SrcMem or DstMem.  This is not the case for several instructions - prefetch,
hint-nop and clflush.

Adding SrcMem|NoAccess for prefetch and hint-nop and SrcMem for clflush.

This fixes CVE-2014-8480.

Fixes: 41061cdb
Cc: stable@vger.kernel.org
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Currently, all group15 instructions are decoded as clflush (e.g., mfence,
xsave).  In addition, the clflush instruction requires no prefix (66/f2/f3)
would exist. If prefix exists it may encode a different instruction (e.g.,
clflushopt).

Creating a group for clflush, and different group for each prefix.

This has been the case forever, but the next patch needs the cflush group
in order to fix a bug introduced in 3.17.

Fixes: 41061cdb
Cc: stable@vger.kernel.org
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

A failure to decode the instruction can cause a NULL pointer access.
This is fixed simply by moving the "done" label as close as possible
to the return.

This fixes CVE-2014-8481.

Reported-by: Andy Lutomirski <luto@amacapital.net>
Cc: stable@vger.kernel.org
Fixes: 41061cdb
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

A platform driver for which nothing ever registers the corresponding
platform device.

Also it was driving the same hardware as sead3-i2c-drv.c so redundant
anyway and couldn't co-exist with that driver because each of them was
using a private spinlock to protect access to the same hardware
resources.

This also fixes a randconfig problem:

arch/mips/mti-sead3/sead3-pic32-i2c-drv.c: In function 'i2c_platform_probe':
arch/mips/mti-sead3/sead3-pic32-i2c-drv.c:345:2: error: implicit declaration of
function 'i2c_add_numbered_adapter' [-Werror=implicit-function-declaration]
  ret = i2c_add_numbered_adapter(&priv->adap);
    ^
arch/mips/mti-sead3/sead3-pic32-i2c-drv.c: In function
'i2c_platform_remove':
arch/mips/mti-sead3/sead3-pic32-i2c-drv.c:361:2: error: implicit declaration
of function 'i2c_del_adapter' [-Werror=implicit-function-declaration]
i2c_del_adapter(&priv->adap);

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Once an instruction crosses a page boundary, the size read from the second page
disregards the common case that part of the operand resides on the first page.
As a result, fetch of long insturctions may fail, and thereby cause the
decoding to fail as well.

Cc: stable@vger.kernel.org
Fixes: 5cfc7e0f
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

KVM_EXIT_UNKNOWN is a kvm bug, we don't really know whether it was
triggered by a priveledged application.  Let's not kill the guest: WARN
and inject #UD instead.

Cc: stable@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

On systems with invvpid instruction support (corresponding bit in
IA32_VMX_EPT_VPID_CAP MSR is set) guest invocation of invvpid
causes vm exit, which is currently not handled and results in
propagation of unknown exit to userspace.

Fix this by installing an invvpid vm exit handler.

This is CVE-2014-3646.

Cc: stable@vger.kernel.org
Signed-off-by: Petr Matousek <pmatouse@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Far jmp/call/ret may fault while loading a new RIP.  Currently KVM does not
handle this case, and may result in failed vm-entry once the assignment is
done.  The tricky part of doing so is that loading the new CS affects the
VMCS/VMCB state, so if we fail during loading the new RIP, we are left in
unconsistent state.  Therefore, this patch saves on 64-bit the old CS
descriptor and restores it if loading RIP failed.

This fixes CVE-2014-3647.

Cc: stable@vger.kernel.org
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Before changing rip (during jmp, call, ret, etc.) the target should be asserted
to be canonical one, as real CPUs do.  During sysret, both target rsp and rip
should be canonical. If any of these values is noncanonical, a #GP exception
should occur.  The exception to this rule are syscall and sysenter instructions
in which the assigned rip is checked during the assignment to the relevant
MSRs.

This patch fixes the emulator to behave as real CPUs do for near branches.
Far branches are handled by the next patch.

This fixes CVE-2014-3647.

Cc: stable@vger.kernel.org
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Relative jumps and calls do the masking according to the operand size, and not
according to the address size as the KVM emulator does today.

This patch fixes KVM behavior.

Cc: stable@vger.kernel.org
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

There's a race condition in the PIT emulation code in KVM.  In
__kvm_migrate_pit_timer the pit_timer object is accessed without
synchronization.  If the race condition occurs at the wrong time this
can crash the host kernel.

This fixes CVE-2014-3611.

Cc: stable@vger.kernel.org
Signed-off-by: Andrew Honig <ahonig@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

The previous patch blocked invalid writes directly when the MSR
is written.  As a precaution, prevent future similar mistakes by
gracefulling handle GPs caused by writes to shared MSRs.

Cc: stable@vger.kernel.org
Signed-off-by: Andrew Honig <ahonig@google.com>
[Remove parts obsoleted by Nadav's patch. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Upon WRMSR, the CPU should inject #GP if a non-canonical value (address) is
written to certain MSRs. The behavior is "almost" identical for AMD and Intel
(ignoring MSRs that are not implemented in either architecture since they would
anyhow #GP). However, IA32_SYSENTER_ESP and IA32_SYSENTER_EIP cause #GP if
non-canonical address is written on Intel but not on AMD (which ignores the top
32-bits).

Accordingly, this patch injects a #GP on the MSRs which behave identically on
Intel and AMD.  To eliminate the differences between the architecutres, the
value which is written to IA32_SYSENTER_ESP and IA32_SYSENTER_EIP is turned to
canonical value before writing instead of injecting a #GP.

Some references from Intel and AMD manuals:

According to Intel SDM description of WRMSR instruction #GP is expected on
WRMSR "If the source register contains a non-canonical address and ECX
specifies one of the following MSRs: IA32_DS_AREA, IA32_FS_BASE, IA32_GS_BASE,
IA32_KERNEL_GS_BASE, IA32_LSTAR, IA32_SYSENTER_EIP, IA32_SYSENTER_ESP."

According to AMD manual instruction manual:
LSTAR/CSTAR (SYSCALL): "The WRMSR instruction loads the target RIP into the
LSTAR and CSTAR registers.  If an RIP written by WRMSR is not in canonical
form, a general-protection exception (#GP) occurs."
IA32_GS_BASE and IA32_FS_BASE (WRFSBASE/WRGSBASE): "The address written to the
base field must be in canonical form or a #GP fault will occur."
IA32_KERNEL_GS_BASE (SWAPGS): "The address stored in the KernelGSbase MSR must
be in canonical form."

This patch fixes CVE-2014-3610.

Cc: stable@vger.kernel.org
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Allows booting from SD/MMC on RK3288 and other platforms. Added here so I
can enable the board in the boot farm.

Signed-off-by: Olof Johansson <olof@lixom.net>

I missed in 9a2ad529 that REGULATOR_FIXED_VOLTAGE had also gotten
deselected, so it needs to be added back as an explicit option.

Signed-off-by: Olof Johansson <olof@lixom.net>

Code before the .fixup section needs to have the .insn directive.
This has no side effects on MIPS32/64 but it affects the way microMIPS
loads the address for the return label.

Fixes the following build problem:
mips-linux-gnu-ld: arch/mips/built-in.o: .fixup+0x4a0: Unsupported jump between
ISA modes; consider recompiling with interlinking enabled.
mips-linux-gnu-ld: final link failed: Bad value
Makefile:819: recipe for target 'vmlinux' failed

The fix is similar to 1658f914 ("MIPS: microMIPS:
Disable LL/SC and fix linker bug.")

Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: stable@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8117/


Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

When CONFIG_MIPS_MT_SMP is enabled, the following compilation error
occurs:

arch/mips/pmcs-msp71xx/msp_irq_cic.c:134: error: ‘irq’ undeclared

This code clearly never saw a compiler.
The surrounding code suggests, that 'd->irq' was intended, not
'irq'.

This error was found with vampyr.

Signed-off-by: Stefan Hengelein <stefan.hengelein@fau.de>
Fixes: d7881fbd ("MIPS: msp71xx: Convert to new irq_chip functions")
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8116/


Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The malta-amon.c file provides functions to access the YAMON Monitoring
interface to bring up secondary VPEs in case of SMP/CMP. As a
result of which, there is no need to build it if CMP is not used.

Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/7993/


Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The no-op cases of cop2_save & cop2_restore lead to the following
warnings being emitted during build with recent versions of gcc (tested
using gcc 4.8.3 from the Mentor Sourcery CodeBench 2014.05 toolchain):

  In file included from ./arch/mips/include/asm/switch_to.h:18:0,
                   from kernel/sched/core.c:78:
  kernel/sched/core.c: In function 'finish_task_switch':
  include/asm-generic/current.h:6:45: warning: value computed is not used [-Wunused-value]
   #define get_current() (current_thread_info()->task)
                                               ^
  ./arch/mips/include/asm/cop2.h:48:32: note: in definition of macro 'cop2_restore'
   #define cop2_restore(r)  do { (r); } while (0)
                                  ^
  include/asm-generic/current.h:7:17: note: in expansion of macro 'get_current'
   #define current get_current()
                   ^
  ./arch/mips/include/asm/switch_to.h:114:16: note: in expansion of macro 'current'
     cop2_restore(current);     \
                  ^
  kernel/sched/core.c:2225:2: note: in expansion of macro 'finish_arch_switch'
    finish_arch_switch(prev);
    ^

Avoid the warning by "using" the value by casting to void.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7880/


Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The MIPS_CPS_PM and MIPS_CPS_CPUIDLE implementation should depend
on the MIPS_CPS symbol to avoid the following build problem

arch/mips/kernel/pm-cps.c: In function 'cps_pm_enter_state':
arch/mips/kernel/pm-cps.c:164:26: error: 'cpu_coherent_mask' undeclared
(first use in this function)
cpumask_clear_cpu(cpu, &cpu_coherent_mask);
                            ^
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/7798/


Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The __pastwait symbol was only used by the address_is_in_r4k_wait_irqoff
function but this is no longer used since the SMTC removal in commit
b633648c ('MIPS: MT: Remove SMTC support'). That symbol also led to
build failures under certain random configuration due to the way the
compiler compiled the r4k_wait_irqoff function. If that function was
called multiple times, the __pastwait symbol was redefined breaking the
build like this:

CHK     include/generated/compile.h
CC      arch/mips/kernel/idle.o
{standard input}: Assembler messages:
{standard input}:527: Error: symbol `__pastwait' is already defined

Link: http://www.linux-mips.org/cgi-bin/mesg.cgi?a=linux-mips&i=1244879922.24479.30.camel%40falcon


Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/7791/


Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Panic if Xen provides a memory map with 0 entries. Although this is
unlikely, it is better to catch the error at the point of seeing the map
than later on as a symptom of some other crash.

Signed-off-by: Martin Kelly <martkell@amazon.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>

Commit 89cbc767 ("x86: Replace __get_cpu_var uses") replaced
__get_cpu_var() with this_cpu_ptr() in xen_clocksource_read() in such a
way that instead of accessing a structure pointed to by a per-cpu pointer
we are trying to get to a per-cpu structure.

__this_cpu_read() of the pointer is the more appropriate accessor.

Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>

When a new p2m leaf is allocated this leaf is linked into the p2m tree
via cmpxchg. Unfortunately the compare value for checking the success
of the update is read after checking for the need of a new leaf. It is
possible that a new leaf has been linked into the tree concurrently
in between. This could lead to a leaked memory page and to the loss of
some p2m entries.

Avoid the race by using the read compare value for checking the need
of a new p2m leaf and use ACCESS_ONCE() to get it.

There are other places which seem to need ACCESS_ONCE() to ensure
proper operation. Change them accordingly.

Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>