Board files for Phytec phyCARD-S "System on Module" and "Rapid
Development Kit".

Based on patches from:

Steffen Trumtrar <s.trumtrar@pengutronix.de>:
 - Original patch
 - ARM: dts: Set partition offsets for phycard
 - ARM: dts: Use CSPI1 instead of CSPI2 on phycard pca100
 - ARM: imx27-phytec-phycard-S.dts: resize nand partitions

Jan Luebbe <jlu@pengutronix.de>:
 - ARM: dts: Enable bad block table in NAND

Cc: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

B2020 ADI board is reference board for STIH415/416 SOCs, it has 2 x
UART, 4x USB, 1 x Ethernet, 1 x SATA, 1 x PCIe, and 2GB RAM  with
standard set-top box IPs.

This patch adds initial support to B2020 with STiH415/416 with SBC_UART1
as console and a heard beat LED.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
CC: Stephen Gallimore <stephen.gallimore@st.com>
CC: Stuart Menefy <stuart.menefy@st.com>
CC: Arnd Bergmann <arnd@arndb.de>

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

B2000 board is reference board for STIH415/416 SOCs, it has
2 x UART, 4x USB, 2 x Ethernet, 1 x SATA, 1 x PCIe, and 1GB RAM.

This patch add initial support to b2000 with STiH415/416 with UART2 as
console and a heard beat LED.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
CC: Stephen Gallimore <stephen.gallimore@st.com>
CC: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>

This patch adds device trees for describing the TI-Nspire hardware.

Changes between v1 and v2:
* Change "keymap" binding to the standard "linux,keymap" binding.

Signed-off-by: Daniel Tang <dt.tangr@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Add AM43x ePOS EVM minimal DT source - this is a minimal one to get
it booting. Also include it in omap2plus dtbs and document bindings.
The hardware is under development.

Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Emilio López <emilio@elopez.com.ar>

The uevm is the only official board supported for the OMAP5 soc
in mainline. The existent sevm platform will no more be supported.
Hence cleaning up the board dts file to have only the data
required for uevm.

Renaming the board dts file and adding the following cleanups.

 * There are no devices connected on I2C 2,3,4 buses. So remove
   the pinmux data for the same.

 * OMAP5432 and DDR3 memory is used in the uevm. Temperature polling
   is not supported with DDR3 memories. Because of DDR3 phy limitation
   the voltage change across DVFS and all shadow registers for DVFS on
   DDR3 is not supported. Hence the emif kernel driver is not required,
   so removing the DDR3 device file and emif nodes for uevm.

 * Keypad is not supported on uevm. So remove the device node.

Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

When making the dtbs target on OMAP/AM35xx, some trees are not
built.

Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

Add initial device tree nodes for EXYNOS5420 SoC and SMDK5420 board.

Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Add a DT fragment for the Zed Zynq platform and a corresponding
target to the Makefile

Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Add a DT fragment for the zc706 Zynq platform and a corresponding
target to the Makefile.

Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Add support for imx6q Phytec phyFLEX-i.MX6 Quad (aka pfla02 and pbab01).
 - Module pfla02
 - Carrier-Board pbab01

Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Patch adds initial dts for Phytec PCM970 Rapid development kit.
- Added definition for UART0 and UART1.
- Added additional SPI chipselect which used on RDK for ZegBee module.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

PCM038 dts can be used as base for development kit board or any
custom PCB designs. Renames this file to match functionality.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add initial Freescale Vybrid VF610 Tower board support
with uart and fec enabled.

Signed-off-by: Jingchang Lu <b35083@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add initial imx6sl-evk board support with uart, usdhc and fec enabled.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

This patch adds support for the DENX M53EVK board. The board currently supports
NAND, Ethernet, UART, CAN, I2C.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The CFA-10057 is a breakout board for the CFA-10036 that has Ethernet,
USB and a 4.3" LCD screen on it.

Signed-off-by: Brian Lilly <brian@crystalfontz.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The CFA-10055 is yet another breakout board for the CFA-10036, and is
basically a CFA-10037, with the screen and LCD controller found on the
CFA-10049.

Signed-off-by: Brian Lilly <brian@crystalfontz.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Provide alternate board code for the Armadillo800EVA to demonstrate how
DT may be used given the current state of driver device tree support.
This is intended to act as a reference for mach-shmobile developers.

This a rather bare bone version with the following devices supported:

 - GIC
 - irqpins
 - i2c0/1
 - touchscreen

Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

the low power version have a mmc-spi

eanble mmc-spi and RV3029C2 RTC in at91_dt_defconfig

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
[nicolas.ferre@atmel.com: re-arranging nodes, removing nodes and some comments]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

This register the most basic peripherals and makes the
U300 boot to prompt from a device tree.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This commit converts the Marvell DB-88F6281/DB-88F6282 board to the
Device Tree. In fact, the code was supporting two different boards:
one with the 6281 SoC variant, and one with the 6282 SoC variant. The
difference between the two being that the 6281 has one PCIe interface,
and the 6282 has two PCIe interfaces.

In order to handle that with the Device Tree, we create a
'kirkwood-db.dtsi' file that contains the definitions common to both
boards, and 'kirkwood-db-88f6281.dts' and 'kirkwood-db-88f6282.dts'
for the definitions specific to each board. This is similar to what is
done for the QNAP TS219 Kirkwood platform.

We have kept one single Kconfig option, just like it was before.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

This makes sure the new ccu8540 DTB file is generated by
the build system.

Cc: Lee Jones <lee.jones@linaro.org>
Cc: Gabriel Fernandez <gabriel.fernandez.st@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Definitions in s3c24xx.dtsi are usable for all s3c24xx
SoCs, but some need to be extended with proper compatible
properties, as can be seen in s3c2416.dtsi.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Commit b00adbe0 ("ARM: sunxi: Rename uart nodes to serial") changed the
node names in the DTSI, changes that were not accordingly made to the
Mini X-Plus device tree. This breakage slipped through because it was
not properly declared in the Makefile.

Fix both issues.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This patch adds support for the WonderMedia WM8750 SoC and the VIA
APC8750 board.

Signed-off-by: Tony Prisk <linux@prisktech.co.nz>

This patch adds basic device tree sources for Universal C210 board.

Currently support includes:
- eMMC
- serial
- max8952 and max8998 voltage regulators.
- gpio-keys

More support will be added in further patches.

Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

xenvm is based on mach-vexpress, move it to mach-virt.

Changes in v4:
- update the dts Makefile too.

Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
CC: Marc Zyngier <marc.zyngier@arm.com>
CC: will.deacon@arm.com
CC: arnd@arndb.de
CC: rob.herring@calxeda.com

Add the versatile platform dtbs to the dtbs make rule.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>

This patch adds DT board setup for the LaCie NAS CloudBox. The CloudBox
is a low cost NAS based on the Network Space v2.

Chipset list:
- CPU MARVELL 88F6702 1Ghz
- SDRAM memory: 256MB DDR2-800 (2x128MB x8) 400Mhz
- 1 Ethernet Gigabit port (PHY MARVELL 88E1318)
- SPI flash, NOR 512KB
- 1 push button
- 2 LEDs (red and blue)

There is no EEPROM and no USB ports embedded.

Note that this board must not be confused with the Network Space Mini v2
which is embedded in a previous LaCie product also named CloudBox.

Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The patch adds missing imx27-phytec-phycore dtb target into Makefile.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Wandboard is a development board that has two variants: one version based
on mx6 dual lite and another one based on mx6 solo.

For more details about Wandboard, please refer to: http://www.wandboard.org/



Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add initial imx6dl-sabreauto support based on the common stuff already
in imx6qdl-sabreauto.dtsi.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add initial imx6dl-sabresd support based on the common stuff already in
imx6qdl-sabresd.dtsi.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add support for MicroSys sbc6x board.

Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The APF27Dev is a docking board for an APF27 SOM

Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The APF51Dev is a docking board for an APF51 SOM

Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>