- Jan 28, 2015
-
-
Saeed Mahameed authored
Use cmd->autoneg as a user hint to decide what to set in ethtool set settings callback. When cmd->autoneg == AUTONEG_ENABLE set according to ethtool->advertise otherwise, set according to ethtool->speed. Usage: - ethtool -s eth<x> speed 56000 autoneg off - ethtool -s eth<x> advertise 0x800000 autoneg on While we're here: - Move proto_admin masking outcome check to be adjacent to the operation. - Move en_warn("port reset..") print to "port reset" block. Fixes: 312df74c ("net/mlx4_en: mlx4_en_set_settings() always fails when autoneg is set") Signed-off-by:Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
Amir Vadai <amirv@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jack Morgenstein authored
mlx4_bf_alloc had an unnecessary/duplicate code line. Did no harm, but not good practice. Reported by the Mellanox Beijing team. Signed-off-by:
Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by:
-
Jack Morgenstein authored
Struct mlx4_vhcr was implicitly padded by the gcc compiler on 64-bit architectures. This commit makes that padding explicit, to prevent issues with changing compilers and with incompatibilities between 32-bit architecture implicit padding and 64-bit architecture implicit padding. This structure is used in virtualization for communication between the Host and its Guests. The explicit padding allows 64-bit Hosts (old and new) to continue to interoperate with 64-bit Guests (old and new). However, without this fix, 64-bit Hosts could not interoperate with 32-bit Guests (since these did not insert the padding dword). With this fix, 32-bit Guests will be able to interoperate with 64-bit Hosts (since the structure offsets will be identical on both). Reported-by:
Alexander Schmidt <alexs@linux.vnet.ibm.com> Signed-off-by:
-
Jack Morgenstein authored
The driver incorrectly assigned an out-mailbox to this command, and used an opcode modifier = 0, which is a reserved value (it should use opcode modifier = 1). Signed-off-by:
-
Jack Morgenstein authored
The firmware spec states that the timeout for all commands should be 60 seconds. In the past, the spec indicated that there were several classes of timeout (short, medium, and long). The driver has these different timeout classes. We leave the class differentiation in the driver as-is (to protect against any future spec changes), but set the timeout for all classes to be 60 seconds. In addition, we fix a few commands which had hard-coded numeric timeouts specified. Signed-off-by:
-
Jack Morgenstein authored
Structs allocated for the resource tracker must be freed in the error flow. Signed-off-by:
-
Jack Morgenstein authored
The reserved lKey is different for each VF. A base lkey value is returned in QUERY_DEV_CAP at offset 0x98. The reserved L_key value for a VF is: VF_lkey = base_lkey + (VF_number << 8). This VF L_key value should be returned in QUERY_FUNC_CAP (opcode-modifier = 0) at offset 0x48. To indicate that the lkey value at offset 0x48 is valid, the Hypervisor sets a flag bit in dword 0x0, offset 27 in the QUERY_FUNC_CAP wrapper function. When the VF calls QUERY_FUNC_CAP, it should check if this flag bit is set. If it is set, the VF should take the reserved lkey value at offset 0x48. If the bit is not set, the VF should not use a reserved lkey (i.e., should set its reserved lkey value to 0). Signed-off-by: -
Jack Morgenstein authored
If the firmware can detect a bad cable, allow it to generate an event, and print the problem in the log. Signed-off-by:
-
Nicolas Dichtel authored
Previous commit is based on a wrong assumption, fdb messages are always sent into the netns where the interface stands (see vxlan_fdb_notify()). These fdb messages doesn't embed the rtnl attribute IFLA_LINK_NETNSID, thus we need to add it (useful to interpret NDA_IFINDEX or NDA_DST for example). Note also that vxlan_nlmsg_size() was not updated. Fixes: 193523bf ("vxlan: advertise netns of vxlan dev in fdb msg") Signed-off-by:
Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by:
-
Jonathan Toppins authored
fix sparse warning about non-static function drivers/net/bonding/bond_main.c:3737:5: warning: symbol 'bond_3ad_xor_xmit' was not declared. Should it be static? Reviewed-by:
Nikolay Aleksandrov <nikolay@redhat.com> Signed-off-by:
Jonathan Toppins <jtoppins@cumulusnetworks.com> Signed-off-by:
Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by:
-
Satish Ashok authored
When a slave is added to a bond and it is not in full duplex mode, AD_PORT_LACP_ENABLED flag is cleared, due to this LACP PDU is not sent on slave. When the duplex is changed to full, the flag needs to be set to send LACP PDU. Cc: Andy Gospodarek <gospo@cumulusnetworks.com> Reviewed-by:
Satish Ashok <sashok@cumulusnetworks.com> Signed-off-by:
-
Wilson Kok authored
This patch attempts to fix the following problems when an actor or partner's aggregator is not active: 1. a slave's lacp port state is marked as AD_STATE_SYNCHRONIZATION even if it is attached to an inactive aggregator. LACP advertises this state to the partner, making the partner think he can move into COLLECTING_DISTRIBUTING state even though this link will not pass traffic on the local side 2. a slave goes into COLLECTING_DISTRIBUTING state without checking if the aggregator is actually active 3. when in COLLECTING_DISTRIBUTING state, the partner parameters may change, e.g. the partner_oper_port_state.SYNCHRONIZATION. The local mux machine is not reacting to the change and continue to keep the slave and bond up 4. When bond slave leaves an inactive aggregator and joins an active aggregator, the actor oper port state need to update to SYNC state. v2: * fix style issues in bond_3ad.c Cc: Andy Gospodarek <gospo@cumulusnetworks.com> Reviewed-by:Wilson Kok <wkok@cumulusnetworks.com> Signed-off-by:
-
Wilson Kok authored
Mode 802.3ad, fix incorrect bond slave active state when slave is not in active aggregator. During bond_open(), the bonding driver always sets the slave active flag to true if the bond is not in active-backup, alb, or tlb modes. Bonding should let the aggregator selection logic set the active flag when in 802.3ad mode. Cc: Andy Gospodarek <gospo@cumulusnetworks.com> Reviewed-by:
-
Jonathan Toppins authored
Cc: Andy Gospodarek <gospo@cumulusnetworks.com> Signed-off-by:
-
Nicholas Mc Guire authored
return type of wait_for_completion_timeout is unsigned long not int, this patch just fixes up the declarations. Signed-off-by:
Nicholas Mc Guire <der.herr@hofr.at> Signed-off-by:
-
Nicholas Mc Guire authored
Signed-off-by:
-
- Jan 27, 2015
-
-
Andy Shevchenko authored
In the case when alloc_netdev fails we return NULL to a caller. But there is no check for NULL in the probe drivers. This patch changes NULL to an error pointer. The function description is amended to reflect what we may get returned. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
-
Govindarajulu Varadarajan authored
With the commit d75b1ade ("net: less interrupt masking in NAPI") napi repoll is done only when work_done == budget. When in busy_poll is we return 0 in napi_poll. We should return budget. Signed-off-by:
Govindarajulu Varadarajan <_govind@gmx.com> Acked-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Ben Hutchings authored
It is possible to see the old value of the LP advertising flags through ethtool after reconfiguring the PHY and before autonegotiation completes. If autonegotiation is turned off then the last value seen will persist indefinitely. Signed-off-by:
Ben Hutchings <ben.hutchings@codethink.co.uk> Acked-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
David L Stevens authored
If a remote machine crashes while there are pending transmit buffers, the sunvnet driver reallocates the ring descriptors giving us enries that have state VIO_DESC_FREE but also an allocated skb. This results in a BUG_ON() call when the remote reboots and we reach that point in the ring. This patch: 1) clears pending tx packets in the ring on port reset 2) changes a BUG_ON() to a pr_warn() when a remote host has given us an invalid descriptor state 3) collapses multiple active buffer frees in a ring to a single message per ring and adds the device name and remote MAC address This fixes the particular problem of not cleaning up pending buffers on a reset, but also prevents us from crashing if the remote handles descriptors out of order or sets an unexpected state for a descriptor. Signed-off-by:
David L Stevens <david.stevens@oracle.com> Signed-off-by:
-
David L Stevens authored
This patch moves the clearing of ring data in vnet_port_free_tx_bufs to after the freeing of pending buffers in the ring. Otherwise, this can result in dereferencing a NULL pointer. Reported-by:
Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by:
-
Ben Hutchings authored
- Use the return value of dma_map_single(), rather than calling virt_to_page() separately - Check for mapping failue - Call dma_unmap_single() rather than dma_sync_single_for_cpu() Signed-off-by:
-
Ben Hutchings authored
dma_map_single() may fail if an IOMMU or swiotlb is in use, so we need to check for this. Signed-off-by:
-
Ben Hutchings authored
Currently we try to clear EDRRR and EDTRR and immediately continue to free buffers. This is unsafe because: - In general, register writes are not serialised with DMA, so we still have to wait for DMA to complete somehow - The R8A7790 (R-Car H2) manual states that the TX running flag cannot be cleared by writing to EDTRR - The same manual states that clearing the RX running flag only stops RX DMA at the next packet boundary I applied this patch to the driver to detect DMA writes to freed buffers: > --- a/drivers/net/ethernet/renesas/sh_eth.c > +++ b/drivers/net/ethernet/renesas/sh_eth.c > @@ -1098,7 +1098,14 @@ static void sh_eth_ring_free(struct net_device *ndev) > /* Free Rx skb ringbuffer */ > if (mdp->rx_skbuff) { > for (i = 0; i < mdp->num_rx_ring; i++) > + memcpy(mdp->rx_skbuff[i]->data, > + "Hello, world", 12); > + msleep(100); > + for (i = 0; i < mdp->num_rx_ring; i++) { > + WARN_ON(memcmp(mdp->rx_skbuff[i]->data, > + "Hello, world", 12)); > dev_kfree_skb(mdp->rx_skbuff[i]); > + } > } > kfree(mdp->rx_skbuff); > mdp->rx_skbuff = NULL; then ran the loop: while ethtool -G eth0 rx 128 ; ethtool -G eth0 rx 64; do echo -n .; done and 'ping -f' toward the sh_eth port from another machine. The warning fired several times a minute. To fix these issues: - Deactivate all TX descriptors rather than writing to EDTRR - As there seems to be no way of telling when RX DMA is stopped, perform a soft reset to ensure that both DMA enginess are stopped - To reduce the possibility of the reset truncating a transmitted frame, disable egress and wait a reasonable time to reach a packet boundary before resetting - Update statistics before resetting (The 'reasonable time' does not allow for CS/CD in half-duplex mode, but half-duplex no longer seems reasonable!) Signed-off-by: -
Ben Hutchings authored
If RX traffic is overflowing the FIFO or DMA ring, logging every time this happens just makes things worse. These errors are visible in the statistics anyway. Signed-off-by:
-
Florian Fainelli authored
As part of a call to ndo_close() a netdevice driver may call phy_disconnect() -> phy_detach() -> phy_suspend(), such that the PHY is suspsended at this point and a netdevice driver may clock gate the backing peripheral providing MDIO bus accessses as well. Update mdio_bus_phy_may_suspend() to return whether a PHY is allowed to be suspended and conversely resumed if and only if it was not previously suspended before while it is currently in detached (netdev pointer is NULL) state. This fixes bus errors seen during S2/S3 suspend/resume cycles for netdevice drivers such as GENET which clock gates the entire Ethernet MAC, including the MDIO bus block. Acked-by:
Fugang Duan <B38611@freescale.com> Tested-by:
-
Florian Fainelli authored
In order to avoid double calls to phydev->drv->suspend and resume, keep track of whether the PHY has already been suspended as a consequence of a successful call to phy_suspend(). We will use this in our MDIO bus suspend/resume hooks to avoid a double suspend call. Signed-off-by:
-
Florian Fainelli authored
phy_suspend and phy_resume are an abstraction on top of the PHY device driver suspend and resume callbacks, utilize those since they are the proper interface to suspending and resuming a PHY device. Acked-by:
-
Hariprasad Shenai authored
Signed-off-by:
Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by:
-
Hariprasad Shenai authored
Signed-off-by:
-
Hariprasad Shenai authored
Signed-off-by:
-
Hariprasad Shenai authored
Signed-off-by:
-
Hariprasad Shenai authored
Signed-off-by:
-
Vivien Didelot authored
Some busy bits are available in the global register 1, such as the ATU Busy bit. We may want to use this function to wait for them to change, so add a new parameter to mv88e6352_wait() instead of hard-coding REG_GLOBAL2. In the meantime, since the REG_READ() macro already checks for error, remove the redundant check for ret < 0. Signed-off-by:
Vivien Didelot <vivien.didelot@savoirfairelinux.com> Acked-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Vivien Didelot authored
This commit adds debug messages for the generic mv88e6xxx read and write routines. The output is similar to this: mdio-gpio mdio-gpio.0: <- addr: 0x1b reg: 0x05 val: 0x4000 mdio-gpio mdio-gpio.0: -> addr: 0x1b reg: 0x07 val: 0x3113 mdio-gpio mdio-gpio.0: -> addr: 0x1b reg: 0x08 val: 0x0330 mdio-gpio mdio-gpio.0: -> addr: 0x1b reg: 0x09 val: 0x0000 This is convenient to dynamically debug operations through debugfs with: echo file mv88e6xxx.c +p > <debugfs>/dynamic_debug/control Signed-off-by: -
Ahmed S. Darwish authored
While being in an ERROR_WARNING state, and receiving further bus error events with error counters still in the ERROR_WARNING range of 97-127 inclusive, the state handling code erroneously reverts back to ERROR_ACTIVE. Per the CAN standard, only revert to ERROR_ACTIVE when the error counters are less than 96. Moreover, in certain Kvaser models, the BUS_ERROR flag is always set along with undefined bits in the M16C status register. Thus use bitwise operators instead of full equality for checking that register against bus errors. Signed-off-by:
Ahmed S. Darwish <ahmed.darwish@valeo.com> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de>
-
Ahmed S. Darwish authored
On some x86 laptops, plugging a Kvaser device again after an unplug makes the firmware always ignore the very first command. For such a case, provide some room for retries instead of completely exiting the driver init code. Signed-off-by:
-
Ahmed S. Darwish authored
Send expected argument to the URB completion hander: a CAN netdevice instead of the network interface private context `kvaser_usb_net_priv'. This was discovered by having some garbage in the kernel log in place of the netdevice names: can0 and can1. Signed-off-by:
-
Ahmed S. Darwish authored
Upon receiving a hardware event with the BUS_RESET flag set, the driver kills all of its anchored URBs and resets all of its transmit URB contexts. Unfortunately it does so under the context of URB completion handler `kvaser_usb_read_bulk_callback()', which is often called in an atomic context. While the device is flooded with many received error packets, usb_kill_urb() typically sleeps/reschedules till the transfer request of each killed URB in question completes, leading to the sleep in atomic bug. [3] In v2 submission of the original driver patch [1], it was stated that the URBs kill and tx contexts reset was needed since we don't receive any tx acknowledgments later and thus such resources will be locked down forever. Fortunately this is no longer needed since an earlier bugfix in this patch series is now applied: all tx URB contexts are reset upon CAN channel close. [2] Moreover, a BUS_RESET is now treated _exactly_ like a BUS_OFF event, which is the recommended handling method advised by the device manufacturer. [1] http://article.gmane.org/gmane.linux.network/239442 http://www.webcitation.org/6Vr2yagAQ [2] can: kvaser_usb: Reset all URB tx contexts upon channel close 889b77f7 [3] Stacktrace: <IRQ> [<ffffffff8158de87>] dump_stack+0x45/0x57 [<ffffffff8158b60c>] __schedule_bug+0x41/0x4f [<ffffffff815904b1>] __schedule+0x5f1/0x700 [<ffffffff8159360a>] ? _raw_spin_unlock_irqrestore+0xa/0x10 [<ffffffff81590684>] schedule+0x24/0x70 [<ffffffff8147d0a5>] usb_kill_urb+0x65/0xa0 [<ffffffff81077970>] ? prepare_to_wait_event+0x110/0x110 [<ffffffff8147d7d8>] usb_kill_anchored_urbs+0x48/0x80 [<ffffffffa01f4028>] kvaser_usb_unlink_tx_urbs+0x18/0x50 [kvaser_usb] [<ffffffffa01f45d0>] kvaser_usb_rx_error+0xc0/0x400 [kvaser_usb] [<ffffffff8108b14a>] ? vprintk_default+0x1a/0x20 [<ffffffffa01f5241>] kvaser_usb_read_bulk_callback+0x4c1/0x5f0 [kvaser_usb] [<ffffffff8147a73e>] __usb_hcd_giveback_urb+0x5e/0xc0 [<ffffffff8147a8a1>] usb_hcd_giveback_urb+0x41/0x110 [<ffffffffa0008748>] finish_urb+0x98/0x180 [ohci_hcd] [<ffffffff810cd1a7>] ? acct_account_cputime+0x17/0x20 [<ffffffff81069f65>] ? local_clock+0x15/0x30 [<ffffffffa000a36b>] ohci_work+0x1fb/0x5a0 [ohci_hcd] [<ffffffff814fbb31>] ? process_backlog+0xb1/0x130 [<ffffffffa000cd5b>] ohci_irq+0xeb/0x270 [ohci_hcd] [<ffffffff81479fc1>] usb_hcd_irq+0x21/0x30 [<ffffffff8108bfd3>] handle_irq_event_percpu+0x43/0x120 [<ffffffff8108c0ed>] handle_irq_event+0x3d/0x60 [<ffffffff8108ec84>] handle_fasteoi_irq+0x74/0x110 [<ffffffff81004dfd>] handle_irq+0x1d/0x30 [<ffffffff81004727>] do_IRQ+0x57/0x100 [<ffffffff8159482a>] common_interrupt+0x6a/0x6a Signed-off-by:
-
Michal Simek authored
Fix compilation warning: drivers/net/ethernet/cadence/macb.c:2415:12: warning: 'macb_suspend' defined but not used [-Wunused-function] static int macb_suspend(struct device *dev) drivers/net/ethernet/cadence/macb.c:2432:12: warning: 'macb_resume' defined but not used [-Wunused-function] static int macb_resume(struct device *dev) when CONFIG_PM=y, CONFIG_PM_SLEEP=n are used. Signed-off-by:
Michal Simek <michal.simek@xilinx.com> Acked-by:
Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by:
-
