- Jan 22, 2019
-
-
Takashi Sakamoto authored
In a series of Fireface, devices transfer asynchronous transaction with MIDI messages. In the transaction, content is different depending on models. ALSA fireface driver has protocol-dependent handler to pick up MIDI messages from the content. In latter models of the series, the transaction is transferred to range of address sequentially. This seems to check continuity of transferred messages. This commit changes prototype of the handler to receive offset of address for received transactions. Signed-off-by:
Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by:
Takashi Iwai <tiwai@suse.de>
-
Sameer Pujar authored
AZX_DCAPS_PM_RUNTIME flag is added to indicate support for runtime PM. azx_has_pm_runtime() is used to check if above is enabled and thus forbid runtime PM calls if needed. Signed-off-by:
Sameer Pujar <spujar@nvidia.com> Reviewed-by:
Ravindra Lokhande <rlokhande@nvidia.com> Reviewed-by:
Mohan Kumar D <mkumard@nvidia.com> Signed-off-by:
-
Sameer Pujar authored
This patch moves clock enable/disable from system resume/suspend to runtime resume/suspend respectively. Along with this hda controller chip init or stop is also moved. System resume/suspend can invoke runtime callbacks and do necessary setup. chip->running can be used to check for probe completion and device access during runtime_resume or runtime_suspend can be avoided if probe is not yet finished. This helps to avoid kernel panic during boot where runtime PM callbacks can happen from system PM. Signed-off-by:
-
Sameer Pujar authored
Explicit clock enable is not required during probe, as this would be managed by runtime PM calls. Clock can be enabled/disabled in runtime resume/suspend. This way it is easier to balance clock enable/disable counts. Signed-off-by:
-
Sameer Pujar authored
This patch adds skeleton of runtime suspend and resume callbacks. Signed-off-by:
-
Sameer Pujar authored
Moved devm_clk_get() API calls to a separate function and the same can be called early in the probe. This is done before runtime PM for the device is enabled. The runtime resume/suspend callbacks can later enable/disable clocks respectively(the support would be added in subsequent patches). Clock handles should be available by the time runtime suspend/resume calls can happen. Signed-off-by:
-
Sameer Pujar authored
This patch enables runtime power management(runtime PM) support for hda. pm_runtime_enable() and pm_runtime_disable() are added during device probe and remove respectively. The runtime PM callbacks will be forbidden if hda controller does not have support for runtime PM. pm_runtime_get_sync() and pm_runtime_put() are added for hda register access. The callbacks for above will be added in subsequent patches. Signed-off-by:
-
- Jan 21, 2019
-
-
Takashi Sakamoto authored
Fireface UFX was shipped by RME GmbH in 2012. This model supports later protocol for management of isochronous communication and synchronization of sampling transmission frequency. This commit adds support for the model. At present, it's not clear how to encode MIDI messages and decide destination address for asynchronous transaction, thus this commit adds support for isochronous communication for PCM frames only. Signed-off-by:
-
Takashi Sakamoto authored
A procedure to retrieve clock configuration is used by two callers. Each of caller has duplicated code to parse bits. This commit adds refactoring to remove the duplicated code. Signed-off-by:
-
Takashi Sakamoto authored
This commit adds refactoring for dump of sync status by adding tables for check bits. Signed-off-by:
-
Takashi Sakamoto authored
This commit adds a member for a callback function to get clock status to former protocol. Signed-off-by:
-
Takashi Sakamoto authored
This commit adds a member for a callback function to switch frame fetching mode to former protocol. Signed-off-by:
-
Takashi Sakamoto authored
This commit adds a member for a callback function to dump status and move existing code to former protocol. Signed-off-by:
-
Takashi Sakamoto authored
In a series of Fireface, latter protocol has no way for drivers to retrieve current clock configuration. On the other hand, this driver has proc node for it. This commit removes a proc node to dump both clock configuration and synchronization status in one proc node. Signed-off-by:
-
Takashi Sakamoto authored
This commit moves codes for Fireface 400 to a file of former protocol. Signed-off-by:
-
Takashi Sakamoto authored
In a series of Fireface, later model supports different protocol from former models. This commit is a preparation to support both of protocols. Signed-off-by:
-
Takashi Iwai authored
The unused variable was forgotten to be removed and now we get a compiler warning: sound/pci/hda/hda_codec.c: In function 'hda_codec_runtime_suspend': sound/pci/hda/hda_codec.c:2926:18: warning: unused variable 'pcm' Fixes: 17bc4815 ("ALSA: pci: Remove superfluous snd_pcm_suspend*() calls") Reported-by:
Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by:
-
- Jan 18, 2019
-
-
Takashi Iwai authored
Pull the PCM suspend improvement / cleanup. This moves the most of snd_pcm_suspend*() calls into PCM's own device PM ops. There should be no change from the functionality POV. Signed-off-by:
-
- Jan 15, 2019
-
-
Takashi Iwai authored
snd_pcm_suspend() is no longer called from outside, so let's make it local static. Also drop a superfluous NULL check there. Reviewed-by:
Jaroslav Kysela <perex@perex.cz> Signed-off-by:
-
Takashi Iwai authored
The PCM suspend procedure was changed for drivers, so that they don't have to call snd_pcm_suspend*() in each callback any longer. Update the documentation to adapt the changes. Reviewed-by:
-
Takashi Iwai authored
The call of snd_pcm_suspend_all() & co became superfluous since we call it in the PCM PM ops. Let's remove them. Reviewed-by:
-
Takashi Iwai authored
The call of snd_pcm_suspend_all() & co became superfluous since we call it in the PCM PM ops. Let's remove them. Reviewed-by:
-
Takashi Iwai authored
The call of snd_pcm_suspend_all() & co became superfluous since we call it in the PCM PM ops. Let's remove them. Reviewed-by:
-
Takashi Iwai authored
The call of snd_pcm_suspend_all() & co became superfluous since we call it in the PCM PM ops. Let's remove them. Reviewed-by:
-
Takashi Iwai authored
The call of snd_pcm_suspend_all() & co became superfluous since we call it in the PCM PM ops. Let's remove them. Reviewed-by:
-
Takashi Iwai authored
The call of snd_pcm_suspend_all() & co became superfluous since we call it in the PCM PM ops. Let's remove them. Reviewed-by:
-
Takashi Iwai authored
The call of snd_pcm_suspend_all() & co became superfluous since we call it in the PCM PM ops. Let's remove them. Reviewed-by:
-
Takashi Iwai authored
The call of snd_pcm_suspend_all() & co became superfluous since we call it in the PCM PM ops. Let's remove them. Reviewed-by:
-
Takashi Iwai authored
The call of snd_pcm_suspend_all() & co became superfluous since we call it in the PCM PM ops. Let's remove them. Reviewed-by:
-
Takashi Iwai authored
The call of snd_pcm_suspend_all() & co became superfluous since we call it in the PCM PM ops. Let's remove them. Reviewed-by:
-
Takashi Iwai authored
ATIIXP driver supports the full PCM resume and saves/restores the running PCM pointer. This used to be done in the suspend and resume callbacks together with snd_pcm_suspend() call. But since we moved the snd_pcm_supsend*() call in PCM device PM ops, this should be moved to a more appropriate place, i.e. the trigger callback. Along with the movement of the PCM suspend/resume code, remove the superfluous snd_pcm_suspend_all() call, too. Reviewed-by:
-
Takashi Iwai authored
Until now we rely on each driver calling snd_pcm_suspend*() explicitly at its own PM handling. However, this can be done far more easily by setting the PM ops to each actual snd_pcm device object. This patch adds the device_type object for PCM stream and assigns to each PCM stream object. The type contains only the PM ops for system suspend; we don't need to deal with the resume in general. The suspend hook simply calls snd_pcm_suspend_all() for the given PCM streams. This implies that the PM order is correctly put, i.e. PCM is suspended before the main (or codec) driver, which should be true in general. If a special ordering is needed, you'd need to adjust the device PM order manually later. This patch introduces a new flag, snd_pcm.no_device_suspend, too. With this flag set, the PCM device object won't invoke snd_pcm_suspend_all() by itself. This is needed for ASoC who wants to manage the PM call orders in its serialized way, and the flag is set in soc_new_pcm() as default. For the non-ASoC world, we can get rid of the manual snd_pcm_suspend calls. This will be done in the later patches. Reviewed-by:
-
- Jan 14, 2019
-
-
Sameer Pujar authored
Program codec stripe through AC_VERB_SET_STRIPE_CONTROL to use multiple sdo lines if supported. Audio needs to be striped across number of sdo lines for simultaneous playbacks of higher resolutions to work. This needs to be implemented only for an Audio Output Converter and only if the stripe bit(AC_WCAP_STRIPE) of Audio Widget Capabilities parameter is 1. Signed-off-by:
Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by:
-
Sameer Pujar authored
Platforms having multiple SORs and hdmi/dp sinks require higher bandwidth to support simultaneous playbacks of higher resolution. If hda controller supports multiple SDO lines, STRIPE can be used to indicate how many of the SDO lines the stream should be striped across. During stream start stripe control bits are programmed to use given number of sdo lines and the same is cleared during stream stop. Signed-off-by:
-
Sameer Pujar authored
bits 16:17 in SD_CTL register refer to stripe control. Added an offset register(AZX_REG_SD_CTL_3B) to have exclusive read/write of corresponding register byte. This helps to avoid unnecessary 32-bit read/write of SD_CTL whenever only stripe or other bits of corresponding byte need to be updated. Also HD audio spec defines SD_CTL as 3 byte register. SD_CTL_STRIPE_MASK(0x3) can be used for stripe control programming and when updating AZX_REG_SD_CTL_3B. Signed-off-by:
-
Sameer Pujar authored
Controllers and codecs can support striping of audio out across multiple SDO lines. The number of supported SDO lines can be specific to chip. GCAP register can be read to know the maximum supported SDO lines. snd_hdac_get_stream_stripe_ctl() is exposed to program stripe bits on controller and codec side. stripe value: 0 for 1SDO, 1 for 2SDO, 2 for 4SDO lines, etc., Signed-off-by:
-
Sameer Pujar authored
Controllers can support multiple Serial Data Out(SDO) lines, for extended outbound bandwidth, to pump data to all codecs on the link. Codecs can sample data present on SDO. Add verbs AC_VERB_GET_STRIPE_CONTROL and AC_VERB_SET_STRIPE_CONTROL These can be used to program usage of SDO lines for codec. Signed-off-by:
-
- Jan 09, 2019
-
-
YueHaibing authored
Fixes gcc '-Wunused-but-set-variable' warning: sound/usb/mixer.c: In function 'parse_audio_feature_unit': sound/usb/mixer.c:1838:28: warning: variable 'first_ch_bits' set but not used [-Wunused-but-set-variable] It never used since 2.6 Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
-
Keyon Jie authored
To enable SIE(Stream Interrupt Enable) in snd_hdac_stream_start(), we should set both mask and value to be "1 << azx_dev->index" for register update, the mask was 0, here fix it. Signed-off-by:
Keyon Jie <yang.jie@linux.intel.com> Signed-off-by:
-
Keyon Jie authored
E.g. for azx_int_enable(), we should set both mask and value to be "AZX_INT_CTRL_EN | AZX_INT_GLOBAL_EN"(the mask was 0) to enable controller CIE and GIE. We have similar issues on setting AZX_GCTL_RESET and AZX_GCTL_UNSOL, here try to correct all of them. Signed-off-by:
-
