We risk reading TMSHIGH register twice, but PHY-A are really rare and we
do not support them at the moment.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rounding up the delta between last-beacon-tsf and tsf to intval is wrong
and can lead to misconfigured timers which breaks beacon transmission.
Fix this by adding intval and subtracting the offset of the tsf within the
current slot.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The Times They Are a-Changin'.

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The WMI tx status event timeout was not aligning with the
TX cleanup timer threshold value. Fix this to handle dropped
packets.

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Reduce the credit size for UB94/95 to fix target hangs.

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Commit "ath9k_htc: Fix AMPDU subframe handling" registered the maximum
subframe limit of the driver with mac80211, which was used in ADDBA
negotiation. While technically correct, this causes inter-operability issues
with a few APs. Revert to the older behavior to fix this.

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The BSSID/AID has to be set for the first associated station interface.
Subsequent interfaces may move out of assoc/disassoc status, in which
case, the BSSID has to be re-calculated from the available interfaces.
Also, ANI should be enabled or disabled based on the current opmode.

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Choose the MY_BEACON filter only in case of a single interface.
Also, set the ATH9K_RX_FILTER_MCAST_BCAST_ALL filter in case
of interfaces.

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The FW does absolutely nothing with the station flags,
so remove them. But keep the field around since it might
come in handy in the future.

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Remove all the unsupported modes like FH, TURBO etc.
Since this requires a FW update, increase the fw version to 1.3

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cmd_index is never used.

Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This is to fix an issue that the throughput of the higher priority
stream gets dropped when a lower priority stream is present.

Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If we go through the entire for loop in
mwifiex_wmm_get_highest_priolist_ptr() and don't find any packets,
set highest_queued_prio to NO_PKT_PRIO_TID (< LOW_PRIO_TID).

Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

add checks to mwifiex_wmm_process_tx() loop so it doesn't re-enter
mwifiex_dequeue_tx_packet() to find it can't send.

Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds highest_queued_prio to track priority of packets as
they are enqueued so that mwifiex_wmm_get_highest_priolist_ptr()
starts checking at the first level where we have packets, instead of
the highest. The function also lowers priority value to the level
where first packet is found.

Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds tx_pkts_queued to track number of packets being
enqueued & dequeued so that mwifiex_wmm_lists_empty() evaluation
is lightweight.

Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This adds a new generic gpio rfkill driver to support rfkill switches
which are controlled by gpios. The driver also supports passing in
data about the clock for the radio, so that when rfkill is blocking,
it can disable the clock.

This driver assumes platform data is passed from the board files to
configure it for specific devices.

Original-patch-by: Anantha Idapalapati <aidapalapati@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In ad-hoc mode, beacon timers are configured differently compared to AP
mode, and (depending on the scenario) can vary enough to make the beacon
tasklet not detect slot 0 based on the TSF.
Since staggered beacons are not (and cannot be) used in ad-hoc mode, it
makes more sense to just hardcode slot 0 here, avoiding unnecessary
TSF reads and calculations.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211 scan code adds separate BSS entries if the same BSS shows up
on multiple channels. However, sme implementation does not use the
frequency when fetching the BSS entry. Fix this by adding channel
information to cfg80211_roamed() and include it in cfg80211_get_bss()
calls.

Please note that drivers using cfg80211_roamed() need to be modified to
fully implement this fix. This commit includes only minimal changes to
avoid compilation issues; it maintains the old (broken) behavior for
most drivers. ath6kl was the only one that I could test, so I updated
it to provide the operating frequency in the roamed event.

Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The changes that were made to rtl8192ce when rtl8192cu was added broke
HT40. The errors included a typo in rtlwifi, a missing routine in
rtl8192ce and a missing callback of that routine in rtl8192c-common.

This patch fixes the regression reported in Bug #35082.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This adds proper RCU annotations to the mesh path
table code, and fixes a number of bugs in the code
that I found while checking the sparse warnings I
got as a result of the annotations.

Some things like the changes in mesh_path_add() or
mesh_pathtbl_init() only serve to shut up sparse,
but other changes like the changes surrounding the
for_each_mesh_entry() macro fix real RCU bugs in
the code.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The locking in mesh_{mpath,mpp}_table_grow not only
has an rcu_read_unlock() missing, it's also racy
(though really only technically since it's invoked
from a single function only) since it obtains the
new size of the table without any locking, so two
invocations of the function could attempt the same
resize.

Additionally, it uses synchronize_rcu() which is
rather expensive and can be avoided trivially here.

Modify the functions to only use the table lock
and use call_rcu() instead of synchronize_rcu().

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211 uses call_rcu() with functions that are
defined in the module, so it must use rcu_barrier()
at module exit time.

Luckily, this seems to not be a problem in practice
as module unload and unregistration takes a long
time and probably does multiple synchronize_rcu().

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Reported-by: Gottfried Haider <gottfried.haider@gmail.com>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

As long as no delay is required b/w channel change, scan work
is proceeding without scheduling a new work. In such case, we
can not abort scan work when the card was unplugged. This patch
completes the scanning immediately whenever the device goes down.

Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Drivers shouldn't attempt to advertise support
for more than one IBSS interface since mac80211
doesn't support that. Check and return an error
from ieee80211_register_hw() in that case.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In order to provide multiple interfaces for a single device,
the driver will be required to advertise all possible
interface configurations to the stack.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We free name "dev" for something generic (like dev abstraction layer).
Additionaly code is cleaner now, especially magic dev->dev-dev chains.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Mesh paths are deleted via mesh_path_del() which properly
deactivates the timer associated to a mesh path.  But if paths were
deleted by mesh_table_free(..., true) timers would not be deactivated.
This fixes this case.

Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

* use proc_mkdir_mode() instead of create_proc_entry(S_IFDIR|...),
  export proc_mkdir_mode() for that, oh well.
* don't supply S_IFREG to proc_create_data(), it's unnecessary

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Cc: <stable@kernel.org>
Reported-by: Mark Davis <marked86@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'wireless-next-2.6' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-2.6