Add support for RTC.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Adding prefetchable memory space to pcie device tree node.
Shifting configuration space to 64-bit address space.
Removing pcie device tree node from amba as it requires size-cells=<2>
in order to access 64-bit address space.

Signed-off-by: Bharat Kumar Gogada <bharatku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Add CCI-400 node to DTSI.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Add debug console to dtsi to be able to enable it in
board dts file.
Keep in your mind that every core has separate dcc port in case you want
to run SMP kernel.
DCC is very helpful communication channel for debugging.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Adding operating-points-v2 for zynqmp.

Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Added the idle-states node to describe zynqmp idle states. Only
cpu-sleep-0 idle state is added in this patch. References to the
idle-states node are added in all CPU nodes. Time values: entry/exit
latencies and min-residency, needs to be tuned. arm,psci-suspend-param
is selected to comply with PSCIv1.0 and Extended StateID format.

Signed-off-by: Stefan Krsmanovic <stefan.krsmanovic@aggios.com>
Acked-by: Will Wong <willw@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Add missing references to all cpu nodes.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Moritz Fischer <mdf@kernel.org>

Nodes without reg properties shouldn't be placed in amba node.
Move them out.

Warnings:
arch/arm64/boot/dts/xilinx/zynqmp-ep108.dtb: Warning (simple_bus_reg):
Node /amba/misc_clk missing or empty reg/ranges property
arch/arm64/boot/dts/xilinx/zynqmp-ep108.dtb: Warning (simple_bus_reg):
Node /amba/i2c_clk missing or empty reg/ranges property
arch/arm64/boot/dts/xilinx/zynqmp-ep108.dtb: Warning (simple_bus_reg):
Node /amba/sata_clk missing or empty reg/ranges property
arch/arm64/boot/dts/xilinx/zynqmp-ep108.dtb: Warning (simple_bus_reg):

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Warnings:
arch/arm64/boot/dts/xilinx/zynqmp-ep108.dtb: Warning
(unit_address_format): Node
/amba/spi@ff040000/spi0_flash0@0/spi0_flash0@00000000 unit name should
not have leading 0s
arch/arm64/boot/dts/xilinx/zynqmp-ep108.dtb: Warning
(unit_address_format): Node
/amba/spi@ff050000/spi1_flash0@0/spi1_flash0@00000000 unit name should
not have leading 0s

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

dtc recently added PCI bus checks. Fix these warnings.

Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

When RLIMIT_STACK is, for example, 256MB, the current code results in a
gap between the top of the task and mmap_base of 256MB, failing to take
into account the amount by which the stack address was randomized.  In
other words, the stack gets less than RLIMIT_STACK space.

Ensure that the gap between the stack and mmap_base always takes stack
randomization and the stack guard gap into account.

Obtained from Daniel Micay's linux-hardened tree.

Link: http://lkml.kernel.org/r/20170622200033.25714-3-riel@redhat.com


Signed-off-by: Daniel Micay <danielmicay@gmail.com>
Signed-off-by: Rik van Riel <riel@redhat.com>
Reported-by: Florian Weimer <fweimer@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Daniel Micay <danielmicay@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Use the ascii-armor canary to prevent unterminated C string overflows
from being able to successfully overwrite the canary, even if they
somehow obtain the canary value.

Inspired by execshield ascii-armor and Daniel Micay's linux-hardened
tree.

Link: http://lkml.kernel.org/r/20170524155751.424-5-riel@redhat.com


Signed-off-by: Rik van Riel <riel@redhat.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Daniel Micay <danielmicay@gmail.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This adds support for compiling with a rough equivalent to the glibc
_FORTIFY_SOURCE=1 feature, providing compile-time and runtime buffer
overflow checks for string.h functions when the compiler determines the
size of the source or destination buffer at compile-time.  Unlike glibc,
it covers buffer reads in addition to writes.

GNU C __builtin_*_chk intrinsics are avoided because they would force a
much more complex implementation.  They aren't designed to detect read
overflows and offer no real benefit when using an implementation based
on inline checks.  Inline checks don't add up to much code size and
allow full use of the regular string intrinsics while avoiding the need
for a bunch of _chk functions and per-arch assembly to avoid wrapper
overhead.

This detects various overflows at compile-time in various drivers and
some non-x86 core kernel code.  There will likely be issues caught in
regular use at runtime too.

Future improvements left out of initial implementation for simplicity,
as it's all quite optional and can be done incrementally:

* Some of the fortified string functions (strncpy, strcat), don't yet
  place a limit on reads from the source based on __builtin_object_size of
  the source buffer.

* Extending coverage to more string functions like strlcat.

* It should be possible to optionally use __builtin_object_size(x, 1) for
  some functions (C strings) to detect intra-object overflows (like
  glibc's _FORTIFY_SOURCE=2), but for now this takes the conservative
  approach to avoid likely compatibility issues.

* The compile-time checks should be made available via a separate config
  option which can be enabled by default (or always enabled) once enough
  time has passed to get the issues it catches fixed.

Kees said:
 "This is great to have. While it was out-of-tree code, it would have
  blocked at least CVE-2016-3858 from being exploitable (improper size
  argument to strlcpy()). I've sent a number of fixes for
  out-of-bounds-reads that this detected upstream already"

[arnd@arndb.de: x86: fix fortified memcpy]
  Link: http://lkml.kernel.org/r/20170627150047.660360-1-arnd@arndb.de
[keescook@chromium.org: avoid panic() in favor of BUG()]
  Link: http://lkml.kernel.org/r/20170626235122.GA25261@beast
[keescook@chromium.org: move from -mm, add ARCH_HAS_FORTIFY_SOURCE, tweak Kconfig help]
Link: http://lkml.kernel.org/r/20170526095404.20439-1-danielmicay@gmail.com
Link: http://lkml.kernel.org/r/1497903987-21002-8-git-send-email-keescook@chromium.org


Signed-off-by: Daniel Micay <danielmicay@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Daniel Axtens <dja@axtens.net>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Now that explicitly executed loaders are loaded in the mmap region, we
have more freedom to decide where we position PIE binaries in the
address space to avoid possible collisions with mmap or stack regions.

For 64-bit, align to 4GB to allow runtimes to use the entire 32-bit
address space for 32-bit pointers.  On 32-bit use 4MB, to match ARM.
This could be 0x8000, the standard ET_EXEC load address, but that is
needlessly close to the NULL address, and anyone running arm compat PIE
will have an MMU, so the tight mapping is not needed.

Link: http://lkml.kernel.org/r/1498251600-132458-4-git-send-email-keescook@chromium.org


Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

We used to read several bytes of the shadow memory in advance.
Therefore additional shadow memory mapped to prevent crash if
speculative load would happen near the end of the mapped shadow memory.

Now we don't have such speculative loads, so we no longer need to map
additional shadow memory.

Link: http://lkml.kernel.org/r/20170601162338.23540-3-aryabinin@virtuozzo.com


Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Since commit fcc8487d ("uapi: export all headers under uapi
directories"), all (and only) headers under uapi directories are
exported, but asm-generic wrappers are still exceptions.

To complete de-coupling the uapi from kernel headers, move generic-y
of exported headers to uapi/asm/Kbuild.

With this change, "make headers_install" will just need to parse
uapi/asm/Kbuild to build up exported headers.

For arm64, "generic-y += kvm_para.h" is doubled in asm/Kbuild and
uapi/asm/Kbuild.  So, the one in the former can be simply removed.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>

A poisoned or migrated hugepage is stored as a swap entry in the page
tables.  On architectures that support hugepages consisting of
contiguous page table entries (such as on arm64) this leads to ambiguity
in determining the page table entry to return in huge_pte_offset() when
a poisoned entry is encountered.

Let's remove the ambiguity by adding a size parameter to convey
additional information about the requested address.  Also fixup the
definition/usage of huge_pte_offset() throughout the tree.

Link: http://lkml.kernel.org/r/20170522133604.11392-4-punit.agrawal@arm.com


Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Steve Capper <steve.capper@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: James Hogan <james.hogan@imgtec.com> (odd fixer:METAG ARCHITECTURE)
Cc: Ralf Baechle <ralf@linux-mips.org> (supporter:MIPS)
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

We don't need to call huge_ptep_offset as our accessors are already
supplied with the pte_t *.  This patch removes those spurious calls.

[punit.agrawal@arm.com: resolve rebase conflicts due to patch re-ordering]
Link: http://lkml.kernel.org/r/20170524115409.31309-3-punit.agrawal@arm.com


Signed-off-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Cc: David Woods <dwoods@mellanox.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Patch series "Support for contiguous pte hugepages", v4.

This patchset updates the hugetlb code to fix issues arising from
contiguous pte hugepages (such as on arm64).  Compared to v3, This
version addresses a build failure on arm64 by including two cleanup
patches.  Other than the arm64 cleanups, the rest are generic code
changes.  The remaining arm64 support based on these patches will be
posted separately.  The patches are based on v4.12-rc2.  Previous
related postings can be found at [0], [1], [2], and [3].

The patches fall into three categories -

* Patch 1-2 - arm64 cleanups required to greatly simplify changing
  huge_pte_offset() prototype in Patch 5.

  Catalin, Will - are you happy for these patches to go via mm?

* Patches 3-4 address issues with gup

* Patches 5-8 relate to passing a size argument to hugepage helpers to
  disambiguate the size of the referred page. These changes are
  required to enable arch code to properly handle swap entries for
  contiguous pte hugepages.

  The changes to huge_pte_offset() (patch 5) touch multiple
  architectures but I've managed to minimise these changes for the
  other affected functions - huge_pte_clear() and set_huge_pte_at().

These patches gate the enabling of contiguous hugepages support on arm64
which has been requested for systems using !4k page granule.

The ARM64 architecture supports two flavours of hugepages -

* Block mappings at the pud/pmd level

  These are regular hugepages where a pmd or a pud page table entry
  points to a block of memory. Depending on the PAGE_SIZE in use the
  following size of block mappings are supported -

          PMD	PUD
          ---	---
  4K:      2M	 1G
  16K:    32M
  64K:   512M

  For certain applications/usecases such as HPC and large enterprise
  workloads, folks are using 64k page size but the minimum hugepage size
  of 512MB isn't very practical.

To overcome this ...

* Using the Contiguous bit

  The architecture provides a contiguous bit in the translation table
  entry which acts as a hint to the mmu to indicate that it is one of a
  contiguous set of entries that can be cached in a single TLB entry.

  We use the contiguous bit in Linux to increase the mapping size at the
  pmd and pte (last) level.

  The number of supported contiguous entries varies by page size and
  level of the page table.

  Using the contiguous bit allows additional hugepage sizes -

           CONT PTE    PMD    CONT PMD    PUD
           --------    ---    --------    ---
    4K:         64K     2M         32M     1G
    16K:         2M    32M          1G
    64K:         2M   512M         16G

  Of these, 64K with 4K and 2M with 64K pages have been explicitly
  requested by a few different users.

Entries with the contiguous bit set are required to be modified all
together - which makes things like memory poisoning and migration
impossible to do correctly without knowing the size of hugepage being
dealt with - the reason for adding size parameter to a few of the
hugepage helpers in this series.

This patch (of 8):

As we regularly check for contiguous pte's in the huge accessors, remove
this extra check from find_num_contig.

[punit.agrawal@arm.com: resolve rebase conflicts due to patch re-ordering]
Link: http://lkml.kernel.org/r/20170524115409.31309-2-punit.agrawal@arm.com


Signed-off-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Cc: David Woods <dwoods@mellanox.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This moves the #ifdef in C code to a Kconfig dependency.  Also we move
the gigantic_page_supported() function to be arch specific.

This allows architectures to conditionally enable runtime allocation of
gigantic huge page.  Architectures like ppc64 supports different
gigantic huge page size (16G and 1G) based on the translation mode
selected.  This provides an opportunity for ppc64 to enable runtime
allocation only w.r.t 1G hugepage.

No functional change in this patch.

Link: http://lkml.kernel.org/r/1494995292-4443-1-git-send-email-aneesh.kumar@linux.vnet.ibm.com


Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

no users left

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Contrary to popular belief, PPIs connected to a GICv3 to not have
an affinity field similar to that of GICv2. That is consistent
with the fact that GICv3 is designed to accomodate thousands of
CPUs, and fitting them as a bitmap in a byte is... difficult.

Fixes: adbc3695 ("arm64: dts: add the Marvell Armada 3700 family and
a development board")
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

With the introduction of struct pci_host_bridge.map_irq pointer it is
possible to assign IRQs for all devices originating from a PCI host bridge
at probe time; this is implemented through pci_assign_irq() that relies on
the struct pci_host_bridge.map_irq pointer to map IRQ for a given device.

The benefits this brings are twofold:

  - the IRQ for a device is assigned once at probe time
  - the IRQ assignment works also for hotplugged devices

With all DT based PCI host bridges converted to the struct
pci_host_bridge.{map/swizzle}_irq hooks mechanism the DT IRQ allocation in
ARM64 pcibios_alloc_irq() is now redundant and can be removed.

Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Will Deacon <will.deacon@arm.com>

This reverts commits 2c0cba48 ("arm: sun8i: sunxi-h3-h5: Add dt node
for the syscon control module") to 2428fd0f ("arm64: defconfig: Enable
dwmac-sun8i driver on defconfig") and 3432a86e ("arm: sun8i:
orangepipc: use internal phy-mode") to 5a79b4f2 ("arm: sun8i:
orangepi-2: use internal phy-mode") that should be merged
through the arm-soc tree, and end up in merge conflicts and build failures.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

struct jit_ctx::image is used the store a pointer to the jitted
intructions, which are always little-endian. These instructions
are thus correctly converted from native order to little-endian
before being stored but the pointer 'image' is declared as for
native order values.

Fix this by declaring the field as __le32* instead of u32*.
Same for the pointer used in jit_fill_hole() to initialize
the image.

Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

Now that compat_vfp_get() uses the regset API to copy the FPSCR
value out to userspace, compat_vfp_set() looks inconsistent.  In
particular, compat_vfp_set() will fail if called with kbuf != NULL
&& ubuf == NULL (which is valid usage according to the regset API).

This patch fixes compat_vfp_set() to use user_regset_copyin(),
similarly to compat_vfp_get().

This also squashes a sparse warning triggered by the cast that
drops __user when calling get_user().

Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

compat_vfp_set() checks for userspace trying to write an excessive
amount of data to the regset.  However this check is conspicuous
for its absence from every other _set() in the arm64 ptrace
implementation.  In fact, the core ptrace_regset() already clamps
userspace's iov_len to the regset size before the individual regset
.{get,set}() methods get called.

This patch removes the redundant check.

Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

If get_user() fails when reading the new FPSCR value from userspace
in compat_vfp_get(), then garbage* will be written to the task's
FPSR and FPCR registers.

This patch prevents this by checking the return from get_user()
first.

[*] Actually, zero, due to the behaviour of get_user() on error, but
that's still not what userspace expects.

Fixes: 478fcb2c ("arm64: Debugging support")
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

get_alt_insn() is used to read and create ARM instructions, which
are always stored in memory in little-endian order. These values
are thus correctly converted to/from native order when processed
but the pointers used to hold the address of these instructions
are declared as for native order values.

Fix this by declaring the pointers as __le32* instead of u32* and
make the few appropriate needed changes like removing the unneeded
cast '(u32*)' in front of __ALT_PTR()'s definition.

Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

In the flattened device tree format, all integer properties are
in big-endian order.
Here the property "kaslr-seed" is read from the fdt and then
correctly converted to native order (via fdt64_to_cpu()) but the
pointer used for this is not annotated as being for big-endian.

Fix this by declaring the pointer as fdt64_t instead of u64
(fdt64_t being itself typedefed to __be64).

Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

ARM64 implementation of ip_fast_csum() do most of the work
in 128 or 64 bit and call csum_fold() to finalize. csum_fold()
itself take a __wsum argument, to insure that this value is
always a 32bit native-order value.

Fix this by adding the sadly needed '__force' to cast the native
'sum' to the type '__wsum'.

Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

Here both variables 'cpu_id' and 'entry_point' are read via
read[lq]_relaxed(), from a little-endian annotated pointer
and then used as a native endian value.

This is correct since the read[lq]() family of function
internally do a little-to-native endian conversion.

But in this case, it is wrong to declare these variable as
little-endian since there are native ones.

Fix this by changing the declaration of these variables
as 'u32' or 'u64' instead of '__le32' / '__le64'.

Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

Here the entrypoint, declared as a 64 bit integer, is read from
a pointer to 64bit integer but the read is done via readl_relaxed()
which is for 32bit quantities.

All the high bits will thus be lost which change the meaning
of the test against zero done later.

Fix this by using readq_relaxed() instead as it should be for
64bit quantities.

Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

Here the functions reloc_insn_movw() & reloc_insn_imm() are used
to read, modify and write back ARM instructions, which are always
stored in memory in little-endian order. These values are thus
correctly converted to/from native order but the pointers used to
hold their addresses are declared as for native order values.

Fix this by declaring the pointers as __le32* and remove the
casts that are now unneeded.

Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

aarch64_insn_write() is used to write an instruction.
As on ARM64 in-memory instructions are always stored
in little-endian order, this function, taking the instruction
opcode in native order, correctly convert it to little-endian
before sending it to an helper function __aarch64_insn_write()
which will do the effective write.

This is all good, but the variable and argument holding the
converted value are not annotated for a little-endian value
but left for native values.

Fix this by adjusting the prototype of the helper and
directly using the result of cpu_to_le32() without passing
by an intermediate variable (which was not a distinct one
but the same as the one holding the native value).

Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

The function arch64_insn_read() is used to read an instruction.
On AM64 instructions are always stored in little-endian order
and thus the function correctly do a little-to-native endian
conversion to the value just read.

However, the variable used to hold the value before the conversion
is not declared for a little-endian value but for a native one.

Fix this by using the correct type for the declaration: __le32

Note: This only works because the function reading the value,
      probe_kernel_read((), takes a void pointer and void pointers
      are endian-agnostic. Otherwise probe_kernel_read() should
      also be properly annotated (or worse, need to be specialized).

Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

Here we're reading thumb or ARM instructions, which are always
stored in memory in little-endian order. These values are thus
correctly converted to native order but the intermediate value
should be annotated as for little-endian values.

Fix this by declaring the intermediate var as __le32 or __le16.

Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

Here we're reading thumb or ARM instructions, which are always
stored in memory in little-endian order. These values are thus
correctly converted to native order but the intermediate value
should be annotated as for little-endian values.

Fix this by declaring the intermediate var as __le32 or __le16.

Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

ARM64 depends on the macro __AARCH64EB__ being defined or not
to correctly select or define endian-specific macros, structures
or pieces of code.

This macro is predefined by the compiler but sparse knows nothing
about it and thus may pre-process files differently from what
gcc would.

Fix this by passing '-D__AARCH64EL__' or '-D__AARCH64EB__' to
sparse depending of the endianness of the kernel, like defined
by GCC.

Note: In most case it won't change anything since most arm64 use
      little-endian (but an allyesconfig would use big-endian!).

CC: Catalin Marinas <catalin.marinas@arm.com>
CC: Will Deacon <will.deacon@arm.com>
CC: linux-arm-kernel@lists.infradead.org
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>