- Feb 28, 2013
-
-
Olof Johansson authored
This refreshes the dove_defconfig, and adds: PRINTK_TIME DEVTMPFS EXT4 They're quite useful, and allows booting a cubox ubuntu rootfs on SD card, since that by default uses ext4. The rest of the churn is due to options and defaults moving around, no functional difference. Signed-off-by:
Olof Johansson <olof@lixom.net> Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Signed-off-by:
Jason Cooper <jason@lakedaemon.net>
-
Andrew Lunn authored
Now that SDIO is instantiated via DT, and the SDIO DT node has a clocks property, we no longer need a C coded clock alias. Remove it. Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Andrew Lunn authored
Now that USB is instantiated via DT, and the USB DT node has a clocks property, we no longer need a C coded clock alias. Remove it. Signed-off-by:
-
Thomas Petazzoni authored
The OpenBlocks AX3-4 platform has several LEDs, so it sounds wise to enable LED support in mvebu_defconfig. We anticipate that more platforms using Marvell EBU SoCs will have LEDs in the future. Signed-off-by:
Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by:
-
Thomas Petazzoni authored
The Globalscale Mirabox platform, based on the Armada 370 from Marvell, has a SD8787 Wireless/Bluetooth chip connected on the SDIO interface. Now that the mvsdio has a Device Tree binding, and the necessary Device Tree informations have been added at the SoC and board level, let's enable the btmrvl driver for the Bluetooth part of the SD8787 chip. For now, the driver gets probed correctly, detects the device but apparently fails to push the firmware to the device: Bluetooth: vendor=0x2df, device=0x911a, class=255, fn=2 Bluetooth: FW failed to be active in time! Bluetooth: Downloading firmware failed! Bluetooth: vendor=0x2df, device=0x911b, class=255, fn=3 Bluetooth: FW failed to be active in time! Bluetooth: Downloading firmware failed! This will have to be investigated separately. Signed-off-by:
-
Thomas Petazzoni authored
The Globalscale Mirabox platform, based on the Armada 370 from Marvell, has a SD8787 Wireless chip connected on the SDIO interface. Now that the mvsdio has a Device Tree binding, and the necessary Device Tree informations have been added at the SoC and board level, let's enable the mwifiex driver for the Wireless part of the SD8787 chip. For now, the driver gets probed correctly, detects a device and shows the network interfaces. However, scanning Wifi networks doesn't work for now, with a 'CMD_RESP: cmd 0x6 error, result=0x1' message. This will have to be investigated separately. Signed-off-by:
-
Thomas Petazzoni authored
Now that the mvsdio driver has gained Device Tree support and the necessary Device Tree informations has been added for Armada 370 and Armada XP platforms, we enable the MMC subsystem and the mvsdio driver in mvebu_defconfig. Signed-off-by:
-
Gregory CLEMENT authored
The RTC class driver is already part of the mvebu_defconfig but the Marvell internal RTC not yet. Now that its support is added for mvebu let's update the config file. Signed-off-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Tested-by:
Florian Fainelli <florian@openwrt.org> Acked-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Arnd Bergmann authored
Basing the mvebu patches on top of the timer cleanup avoids some nasty merges. Signed-off-by: -
Arnd Bergmann authored
These patches from the mmc tree were merged into v3.9 already and the later mvebu patches depend on them. Signed-off-by:
-
- Feb 24, 2013
-
-
Thomas Petazzoni authored
On many Marvell SoCs, the pins used for the SDIO interface are part of the MPP pins, that are muxable pins. In order to get the muxing of those pins correct, this commit integrates the mvsdio driver with the pinctrl infrastructure by calling devm_pinctrl_get_select_default() during ->probe(). Note that we permit this function to fail because not all Marvell platforms have yet been fully converted to using the pinctrl infrastructure. Signed-off-by:
Stefan Peter <s.peter@mpl.ch> Tested-by:
Chris Ball <cjb@laptop.org>
-
- Feb 11, 2013
-
-
Thomas Petazzoni authored
This patch adds a simple Device Tree binding for the mvsdio driver, as well as the necessary documentation for it. Compatibility with non-DT platforms is preserved, by keeping the platform_data based initialization. We introduce a small difference between non-DT and DT platforms: DT platforms are required to provide a clocks = <...> property, which the driver uses to get the frequency of the clock that goes to the SDIO IP. The behaviour on non-DT platforms is kept unchanged: a clock reference is not mandatory, but the clock frequency must be passed in the "clock" field of the mvsdio_platform_data structure. Signed-off-by:
-
Thomas Petazzoni authored
The MMC core subsystem provides in drivers/mmc/core/slot-gpio.c a nice set of helper functions to simplify the management of the card detect GPIO in MMC host drivers. This patch migrates the mvsdio driver to using those helpers, which will make the ->probe() code simpler, and therefore ease the process of adding a Device Tree binding for this driver. Signed-off-by:
-
Thomas Petazzoni authored
The MMC core subsystem provides in drivers/mmc/core/slot-gpio.c a nice set of helper functions to simplify the management of the write protect GPIO in MMC host drivers. This patch migrates the mvsdio driver to using those helpers, which will make the ->probe() code simpler, and therefore ease the process of adding a Device Tree binding for this driver. Signed-off-by:
-
Shawn Guo authored
With commit 9444e07 (mmc: remove unncessary mmc_gpio_free_cd() call from slot-gpio users) in place, the ESDHC_CD_GPIO handling in IO accessories becomes unnecessary. Remove it. Signed-off-by:
Shawn Guo <shawn.guo@linaro.org> Signed-off-by:
-
Andy Shevchenko authored
There are three places where same piece of code is used. Let's split it to a separate function. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
-
Kevin Liu authored
[cjb: The MMP3 architecture requires a registered interrupt to retire wfi when waking from suspend.] Signed-off-by:
Jialing Fu <jlfu@marvell.com> Signed-off-by:
Kevin Liu <kliu5@marvell.com> Signed-off-by:
-
Kevin Liu authored
Don't disable SD Host IRQ during suspend if it is wake up source. Enable wakeup event during suspend. Signed-off-by:
-
Kevin Liu authored
Current code missed disabling interrupts before free irq which is shared. Notice below comments for function free_irq (kernel/irq/manage.c): On a shared IRQ the caller must ensure the interrupt is disabled on the card it drives before calling this function. Original code has below issue during suspend/resume when multiple SD hosts share the same IRQ: 1. Assume there are two hosts (host1 for emmc while host2 for sd) share the same mmc irq. 2. When system suspend, host2 will be suspended before host1. So the sequence is below: step1: irq handler for host2 removed -> step2: irq handler for host1 removed and irq disabled -> ... system suspended ... ... system resumed ... step3: irq enabled and the irq handler for host1 restored -> step4: irq handler for host2 restored 3. So there is the buggy time slot that the irq is enabled but the irq handler for host2 is removed. Then host2 interrupt can be triggered but can't be handled at that moment. Signed-off-by:
-
Stephen Warren authored
Add a very simple driver for the BCM2835 SoC, which is used in the Raspberry Pi board. Signed-off-by:
Stephen Warren <swarren@wwwdotorg.org> Signed-off-by:
-
Konstantin Dorfman authored
When current request is running on the bus and if next request fetched by mmcqd is NULL, mmc context (mmcqd thread) gets blocked until the current request completes. This means that if new request comes in while the mmcqd thread is blocked, this new request can not be prepared in parallel to current ongoing request. This may result in delaying the new request execution and increase it's latency. This change allows to wake up the MMC thread on new request arrival. Now once the MMC thread is woken up, a new request can be fetched and prepared in parallel to the current running request which means this new request can be started immediately after the current running request completes. With this change read throughput is improved by 16%. Signed-off-by:
Konstantin Dorfman <kdorfman@codeaurora.org> Reviewed-by:
Seungwon Jeon <tgih.jun@samsung.com> Signed-off-by:
-
Seungwon Jeon authored
Unlike normal r/w request, special requests(discard, flush) is finished with a one-time issue_fn. Request change to mqrq_prev makes unnecessary call. Signed-off-by:
-
Guennadi Liakhovetski authored
The classical way to process IRQs is read out the status, ack all triggered IRQs, possibly mask them, then process them. Follow this simple procesure instead of the current complex custom algorithm. Signed-off-by:
Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
-
Teppei Kamijou authored
Make error reporting in the driver more verbose. This patch is based on an earlier work by Teppei Kamijou, but we try to not add any new error messages to the log in the normal case to avoid confusing the user, and also add a few more dev_dbg() calls. Signed-off-by:
Teppei Kamijou <teppei.kamijou.yb@renesas.com> Signed-off-by:
Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com> [g.liakhovetski@gmx.de: avoid producing new errors in normal case] Signed-off-by:
-
Guennadi Liakhovetski authored
The INT_BUFWEN IRQ often arrives with other bits set too. If they are not cleared, an additional IRQ can be triggered, sometimes also after the MMC request has already been completed. This leads to block I/O errors. Earlier Teppei Kamijou also observed these additional interrupts and proposed to explicitly wait for them. This patch chooses an alternative approach of clearing all active bits immediately, when processing the main interrupt. Reported-by:
-
Guennadi Liakhovetski authored
DMA completion can be signalled from the DMA callback and from the error handler. If both are called, the completion struct can enter an inconsistent state. To prevent this move completion initialisation immediately before activating DMA. Signed-off-by:
-
Guennadi Liakhovetski authored
If a command execution has produced an error, it has to be reset as a part of the error handling. Signed-off-by:
-
Guennadi Liakhovetski authored
Oopses have been observed on SMP in the sh-mmcif IRQ thread, when the two IRQ threads run simultaneously on two CPUs. Also take care to guard the timeout work and the DMA completion callback from possible NULL-pointer dereferences and races. Signed-off-by:
-
Guennadi Liakhovetski authored
Use "return condition" instead of "if (condition) return true; return false" in functions, returning bool. Signed-off-by:
-
Teppei Kamijou authored
If a DMA transaction fails, terminate all outstanding DMA transfers and unmap buffers. Signed-off-by:
-
Guennadi Liakhovetski authored
Read block and write block operations are currently missing completion timeouts. Add missing timeouts and consolidate them at one location. Signed-off-by:
-
Teppei Kamijou authored
SH/R-Mobile MMCIF host controller can wait while the card signals busy. Set MMC_CAP_WAIT_WHILE_BUSY to inform an upper layer (core/mmc_ops.c) not to insert unnecessary mmc_delay(). Signed-off-by:
-
Teppei Kamijou authored
Timeout period should be properly normalized using msecs_to_jiffies(). Signed-off-by:
-
Teppei Kamijou authored
Some MMCIF implementations support the Dual Data Rate. With this patch, platforms can set the MMC_CAP_UHS_DDR50 capability flag in MMCIF platform data. This will let the MMC core to actually use the DDR mode. Signed-off-by:
-
Shinya Kuribayashi authored
On newer SoCs like R-Mobile U2, MMCIF interrupts are bundled. Signed-off-by:
-
Teppei Kamijou authored
With this post-v2.6.35 change applied: commit a0a1a5fd Author: Tejun Heo <tj@kernel.org> Date: Tue Jun 29 10:07:12 2010 +0200 workqueue: reimplement workqueue freeze using max_active freeze_workqueues_begin() was introduced and workqueue now gets frozen before device drivers suspend operations. We have to ensure that run-time PM suspend operation completes before system-wide suspend is started. Signed-off-by:
-
Teppei Kamijou authored
mmc_rescan() sends CMD52 (SD_IO_RW_DIRECT) to reset SDIO card during card detection. CMD52 should be ignored by SD/eMMC cards, but we can also abort it in the driver immediately, since MMCIF doesn't support SDIO cards anyway. Signed-off-by:
-
Shawn Guo authored
Use slot-gpio helpers to save some code in the driver. Signed-off-by:
-
Shawn Guo authored
Since slot-gpio uses devm_* managed functions in mmc_gpio_request_cd() now, we can remove those mmc_gpio_free_cd() call from host drivers' .probe() error path and .remove(). Signed-off-by:
-
Shawn Guo authored
Use devm_* managed functions, so that slot-gpio users do not have to call mmc_gpio_free_ro/cd to free up resources requested in mmc_gpio_request_ro/cd. Signed-off-by:
-
