The tsadcc node is useless as it doesn't refer to anything and the touchscreen
is handled by the adc0 node.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Define at91sam9rlek crystal frequencies.

Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Move at91sam9rl SoC to the new main/slow clock model.

Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Define at91sam9261ek main crystal frequency.

Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Jean-Jacques HIBLOT <jjhiblot@traphandler.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Jean-Jacques HIBLOT <jjhiblot@traphandler.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Define crystal properties of sama5d3 xplained board.

Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Define crystal frequencies of sama5d3xcm boards.

Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Replace the old main and clk definitions (fixed rate clk) by the new main and
slow clk subtree definition (ck = mux(rc_osc, osc)).

Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Tegra124 only has 4 UARTs. Parts of the documentation hint at a fifth
UART, but this appears to be left-over from earlier SoC documentation.
Remove the non-existent DT node for UART5.

Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Few things were out of order:

- removed ARCH_BCM2835 duplicate
- shuffled ARCH_BCM_5301X, ARCH_U8500 and ARCH_U300 around so to keep the
  list sorted

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Signed-by: Domenico Andreoli <domenico.andreoli@linux.com>

Signed-off-by: Arnd Bergmann <arnd@arndb.de>

s/interrupts-names/interrupt-names/g
s/clocks-names/clock-names/g

Some of the binding files and device tree files get this wrong and the
kernel won't be able to pick it up. Fix them up now so that they don't
get widely used.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by : Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>

Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Specify the 'clock-latency' property to avoid certain cpufreq governors
from refusing to work with the following error:
  ondemand governor failed, too long transition latency of HW, fallback to performance governor

Reported-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

BeagleBoard xM A/B has an inverted usb hub enable line vs the xM C

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
[tony@atomide.com: updated for missing bracket]
Signed-off-by: Tony Lindgren <tony@atomide.com>

shiraz.hashim@st.com email-id doesn't exist anymore as he has left the
company.  Replace ST's id with shiraz.linux.kernel@gmail.com.

It also updates .mailmap file to fix address for 'git shortlog'.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Shiraz Hashim <shiraz.linux.kernel@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: linux-omap@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Tony Lindgren <tony@atomide.com>

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: linux-omap@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Tony Lindgren <tony@atomide.com>

In "ARM: dts: am33xx: correcting dt node unit address for usb", the
usb_ctrl_mod and cppi41dma nodes were updated with the correct register
addresses.  However, the dts files that reference these nodes were not
updated, and those devices are no longer being enabled.

This patch corrects the references for the affected dts files.

Signed-off-by: Leigh Brown <leigh@solinno.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Remove all remaining uses of gpmc,device-nand that have been added since
the property was removed by commit f40739fa ("ARM: dts: OMAP2+:
Simplify NAND support").

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Wrong documentation in pinmux description can be especially confusing.
Keep it proper.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The correct bit is 24 for AHCLKX.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The USB3 PHY driver (ti-pipe3) was updated so that the relevant
clock phandles are expected in the DT node.
Provide the necessary clocks.

Reported-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Most of the clock related dt-binding header files are located in
dt-bindings/clock folder. It would be good to keep all the similar
header files at a single location.

Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
CC: Rob Landley <rob@landley.net>
CC: Andrew Victor <linux@maxim.org.za>
CC: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Acked-by: Boris BREZILLON <b.brezillon.dev@gmail.com>
[nicolas.ferre@atmel.com: add new at91sam9261 & at91sam9rl]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The PD16 is the CS3 for SPI0 while not SPI1.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The default behaviour of the uart-rx pins on the rk3188 is to be pulled up and
a lot of designs use diodes to even prevent them from being raised from the
outside.

Therefore change the rx-pin settings accordingly.

This also fixes a uart receive problem on mass production Radxa Rock boards.

Signed-off-by: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Fix typo of renesas,groups in the koeslch dt. The kernel has no
renesas,gpios but this should match renesas,groups.

Noticed thanks to similar fix for Lager by Rob Taylor and Ben Dooks.

Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This is likely a copy-and-paste error from the
ARM GIC documentation, that has already been fixed.

address-cells should have been set to 0, as with the size
cells. As having those properties set to 0 is the
same thing as not specifying them, drop them completely.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This is likely a copy-and-paste error from the
ARM GIC documentation, that has already been fixed.

address-cells should have been set to 0, as with the size
cells. As having those properties set to 0 is the
same thing as not specifying them, drop them completely.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Per bindings of fixed-clock, #clock-cells is a required property.  Let's
add it for those fixed rate clocks.

Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

This is likely a copy-and-paste error from the
ARM GIC documentation, that has already been fixed.

address-cells should have been set to 0, as with the size
cells. As having those properties set to 0 is the
same thing as not specifying them, drop them completely.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

In case the bootloader has incorrectly configured the ALT mode of
MX6SL_PAD_ECSPI1_SS0 pad, we end up with the following probe error:

m25p80 spi0.0: found mr25h256, expected m25p32
m25p80 spi0.0: mr25h256 (32 Kbytes)

In order to avoid this issue, add an entry for MX6SL_PAD_ECSPI1_SS0 pad, so
that kernel configures the ECSPI chip select as GPIO functionality, which
results in correct SPI NOR probe.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

The 'remote-endpoint' property should point back to ipu_di1_lvds1
rather than ipu_di0_lvds0.

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

Since commit (655b43cc staging: imx-drm-core: Use OF graph to find
components and connections between encoder and crtcs), 'crtcs' becomes a
dead property.  Remove it.

Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>

With the recent imx-drm device tree binding changes, we need to add IPU
DI ports and endpoints for adapting.

Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Lothar Waßmann <LW@KARO-electronics.de>

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

GPIO7_12 switches the D+/D- USB lines on and off. When we use this as
VBUS regulator it means that USB device mode can never work as VBUS is
never turned on in Device mode.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

Bit 6,7 are marked as reserved for the ethernet RGMII pins, so avoid
setting these bits.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

Those two properties should have been set to zero, which
is the same as not specifying them.

Having address-cells set to 1 causes OF interrupt
mapping routines to add 1 to the interrupt-cells
property and as result fail because all calculations
are off by one.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>