Ensure the console uart (UART3) on these boards is mux'd correctly, and
IO ring wakeup is enabled.

This is needed for serial console wakeups when using DT boot.

Thanks to Florian Vaussard for suggestion to use preprocessor
features.

Cc: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

Booting omap5 uevm results in the following error
"did not get pins for uart error: -19"

This happens because omap5 uevm dts file is not adapted
to use uart through pinctrl framework.
Populate uart pinctrl data to get rid of the error.

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
[r.sricharan@ti.com: Replaced constants with preprocessor macros]
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

Add support for blue LED 1 off of GPIO 153.
Make the LED a heartbeat LED
Configure the MUX for GPIO output.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
[r.sricharan@ti.com: Replaced constants with preprocessor macros]
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

Provide the RESET regulators for the USB PHYs, the USB Host
port modes and the PHY devices.

Also provide pin multiplexer information for the USB host
pins.

Signed-off-by: Roger Quadros <rogerq@ti.com>
[r.sricharan@ti.com: Replaced constants with preprocessor macros]
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

The uevm is the only official board supported for the OMAP5 soc
in mainline. The existent sevm platform will no more be supported.
Hence cleaning up the board dts file to have only the data
required for uevm.

Renaming the board dts file and adding the following cleanups.

 * There are no devices connected on I2C 2,3,4 buses. So remove
   the pinmux data for the same.

 * OMAP5432 and DDR3 memory is used in the uevm. Temperature polling
   is not supported with DDR3 memories. Because of DDR3 phy limitation
   the voltage change across DVFS and all shadow registers for DVFS on
   DDR3 is not supported. Hence the emif kernel driver is not required,
   so removing the DDR3 device file and emif nodes for uevm.

 * Keypad is not supported on uevm. So remove the device node.

Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

When making the dtbs target on OMAP/AM35xx, some trees are not
built.

Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

Using constants for pinctrl allows a better readability, and removes
redundancy with comments.

Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Tested-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

Use standard GPIO constants to enhance the readability of DT GPIOs.

Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Tested-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

Replace /include/ by #include for AM33XX and AM35XX device tree
files, in order to use the C pre-processor, making use of #define
features possible.

Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Tested-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

DT source (minimal) for AM4372 SoC to represent AM43x SoC's. Those
represented here are the minimal DT nodes necessary to get kernel
booting.

In DT nodes, "ti,hwmod" property has not been added, this would be
added along with PRCM support for AM43x.

Signed-off-by: Ankur Kishore <a-kishore@ti.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

Update the dt property ti,audpwron-gpio to use the
gpio macro definition for GPIO_ACTIVE_HIGH.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

The GPIO for LED D1 on the omap4-panda a1-a3 rev and the omap4-panda-es
are different.

A1-A3 = gpio_wk7
ES = gpio_110

There is no change to LED D2

Abstract away the pinmux and the LED definitions for the two boards into
the respective DTS files.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

Using constants for pinctrl allows a better readability, and removes
redundancy with comments.

Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

Use the constants defined in include/dt-bindings/interrupt-controller/
to enhance readability.

Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

Use standard GPIO constants to enhance the readability of DT GPIOs.

Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

Replace /include/ by #include for OMAP2+ DT, in order to use the
C pre-processor, making use of #define features possible.

Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

GPMC controller on AM335x-EVM has a NAND flash connected to it.
This patch updates following in am335x-evm.dts:
- adds nandflash specific pin-mux configs
- adds nand node as child of GPMC contoller, with information about
  NAND flash interface, NAND partition table, ECC scheme, elm handle id.
- updates GPMC node for newer GPMC DT properties added in linux-3.10.

Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Gupta, Pekon <pekon@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

ELM hardware engine is used for locating bit-flips in NAND data
This patch is required for working of hardware based NAND ECC schemes
with DT support.

Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

The IGEP COM Module has an 512MB NAND flash memory.

Add a device node for this NAND and its partition layout.

Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

The IGEPv2 board has an 512MB NAND flash memory.

Add a device node for this NAND and its partition layout.

Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

The IGEPv2 board has an SMSC LAN9221i ethernet chip connected to
the OMAP3 processor though the General-Purpose Memory Controller.

This patch adds a device node for the ethernet chip as a GPMC child
and all its dependencies (regulators, GPIO and pin muxs).

Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

xdma_event_intr1.clkout2 pad can be used to source clock
from either 32K OSC or any of the PLL (except MPU) outputs.
On the existing AM335x based boards (EVM, EVM-SK and Bone),
this pad is used to feed the clock to audio codes.

So, this patch configures the pinmux to get clkout2 on the pad.

Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

Add pin control binding for UART0 device nodes in all
board specific DT files.

Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Matt Porter <mporter@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

With DT support, where naming convention is based on base-addr
and not id, so we should follow TRM/Spec numbering label.

This patch changes UART numbering as per TRM, as uart0-5.

Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Matt Porter <mporter@ti.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

Now gpio-leds driver is using devm_pinctrl_get_select_default()
api to set default pinmux configuration required for the
functionality of the driver, so this patch moves respective
pinctrl binding inside leds node.

Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

Add pin control binding for I2C device nodes in all
board specific DT files (as per current usage),

EVM: Both i2c0 and i2c1
EVM-SK and Bone: Only i2c0

Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Matt Porter <mporter@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

The carveouts that have been reserved for multimedia usecases
are not being used currently by any driver and so have been
cleaned up. Memory will be allocated runtime through CMA for
enabling the multimedia usecases.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

The ranges DT entry needed by the PCIe controller is defined at the
SoC .dtsi level. However, some boards have a NOR flash, and to support
it, they need to override the SoC-level ranges property to add an
additional range. Since PCIe and NOR support came separately, some
boards were not properly changed to include the PCIe range in their
ranges property at the .dts level.

This commit fixes those platforms.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The previous mask values for the legacy ARM CPU IDs were conflicting
with the CPU ID assignments for late-generation CPUs (like the
Qualcomm MSM/QSD or Broadcom Brahma-15 processors). This change
corrects the legacy ARM CPU ID value so that the jump table can
fall-through to the appropriate cache maintenance / MMU functions.

Signed-off-by: Marc C <marc.ceeeee@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

In August 2012, Matthew Gretton-Dann checked a change into binutils
labelled "Error on obsolete & warn on deprecated registers", apparently as
part of ARMv8 support. Apparently, this was supposed to emit the message
"Warning: This coprocessor register access is deprecated in ARMv8" when
using certain mcr/mrc instructions and building for ARMv8. Unfortunately,
the message that is actually emitted appears to be '(null)', which is
less helpful in comparison.

Even more unfortunately, this is biting us on every single kernel
build with a new gas, because arch/arm/boot/compressed/head.S and some
other files in that directory are built with -march=all since kernel
commit 80cec14a "[ARM] Add -march=all to assembly file build in
arch/arm/boot/compressed" back in v2.6.28.

This patch reverts Russell's nice solution and instead marks the head.S
file to be built for armv7-a, which fortunately lets us build all
instructions in that file without warnings even on the broken binutils.

Without this patch, building anything results in:

arch/arm/boot/compressed/head.S: Assembler messages:
arch/arm/boot/compressed/head.S:565: Warning: (null)
arch/arm/boot/compressed/head.S:676: Warning: (null)
arch/arm/boot/compressed/head.S:698: Warning: (null)
arch/arm/boot/compressed/head.S:722: Warning: (null)
arch/arm/boot/compressed/head.S:726: Warning: (null)
arch/arm/boot/compressed/head.S:957: Warning: (null)
arch/arm/boot/compressed/head.S:996: Warning: (null)
arch/arm/boot/compressed/head.S:997: Warning: (null)
arch/arm/boot/compressed/head.S:1027: Warning: (null)
arch/arm/boot/compressed/head.S:1035: Warning: (null)
arch/arm/boot/compressed/head.S:1046: Warning: (null)
arch/arm/boot/compressed/head.S:1060: Warning: (null)
arch/arm/boot/compressed/head.S:1092: Warning: (null)
arch/arm/boot/compressed/head.S:1094: Warning: (null)
arch/arm/boot/compressed/head.S:1095: Warning: (null)
arch/arm/boot/compressed/head.S:1102: Warning: (null)
arch/arm/boot/compressed/head.S:1134: Warning: (null)

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: stable@vger.kernel.org
Cc: Matthew Gretton-Dann <matthew.gretton-dann@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Selecting this option produces:

  AS      arch/arm/boot/compressed/debug.o
arch/arm/boot/compressed/debug.S:4:33: fatal error: mach/debug-macro.S: No such file or directory
compilation terminated.
make[3]: *** [arch/arm/boot/compressed/debug.o] Error 1

The semihosting support cannot be modelled into a senduart macro as
it requires memory space for argument passing.  So the
CONFIG_DEBUG_LL_INCLUDE may not have any sensible value and the include
directive should be omitted.

While at it, let's add proper semihosting output support to the
decompressor.

Signed-off-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

OMAP5 has 6 timers (GPTimers 5, 6, 8 to 11) that are capable of PWM.
The PWM capability property is missing from the node definitions of
couple of timers.

Add ti,timer-pwm attribute for timer 5, 6, 8 and 11.

Signed-off-by: Suman Anna <s-anna@ti.com>
[benoit.cousson@linaro.org: Update changelog and subject to highlight
the fix]
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

Earlier commits ensured proper muxing of pins related to proper
TWL6030 behavior: see commit 265a2bc8 (ARM: OMAP3: TWL4030: ensure
sys_nirq1 is mux'd and wakeup enabled) and commit 1ef43369 (ARM:
OMAP4: TWL: mux sys_drm_msecure as output for PMIC).

However these only fixed legacy boot and not DT boot.  For DT boot,
the default mux values need to be set properly in DT.

Special thanks to Nishanth Menon for the review and catching some
major flaws in earlier versions.

Tested on OMAP4430/Panda and OMAP4460/Panda-ES.

Cc: Nishanth Menon <nm@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
[benoit.cousson@linaro.org: Slightly change the subject to align
board name with file name]
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

The gpmc driver is actually looking for "gpmc,num-cs" and
"gpmc,num-waitpins" properties in DT. The binding doc also states
this.
Correct the properties in the dts to provide the right values for the
gpmc driver.

Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

Stephen Warren reported the recent commit 78506f22 (add support for
extended FIFO-size of PL011-r1p5) breaks the serial port on the
BCM2835 ARM SoC.

A UART compatible with the ARM PL011-r1p5 should have 32-deep FIFOs.
The BCM2835 UART just looks like an ARM PL011-r1p5, but has 16-deep
FIFOs just like PL011-r1p4 or earlier revisions. As a workaround for
this compatibility issue, this patch overrides the HW UART periphid
register values with the actually compatible UART periphid 0x00241011
(r1p3 or r1p4).

Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Jongsung Kim <neidhard.kim@lge.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

The PA24 pin is wrongly assigned to peripheral B.
In the current config there is 2 ETX3 pins (PA11 and PA24) and
no ETXER pin (PA22).

Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: stable <stable@vger.kernel.org> # 3.8+

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The CSPI controller has only one clock, but the driver spi-imx.c needs
clock "per" to calculate bitrate divisor.

Signed-off-by: Jonas Andersson <jonas@microbit.se>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The assignment of IRQ for the SMC91x ethernet adapter had two
problems making it non-working:

- It was not put into the ethernet device node. Let's do this
  by using the board-specific overlay, so we can make other
  overlays on other Nomadik boards.

- The IRQ number was actually completely wrong, this was the
  number for NHK8815, not S8815.

After this ethernet starts working on the USB S8815.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

During the conversion to the internal-regs' subnode, the L2-cache node
haven not been converted (due to a wrong choice made by myself during
the resolution of the merge conflict when I rebased the commit). This
leads to wrong address for L2 cache which prevent it to be used on
Armada 370. This commit fix the address reg of the e L2-cache node.

Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>