Commit a819c4f1 (ARM: OMAP3: PM: Only access IVA if one exists)
changed PM to not access IVA registers on omaps that don't have
them. Turns out we still need to idle iva2 as otherwise
iva2_pwrdm will stay on and block deeper idle states.

It seems that the only part of the reset that may not be needed
is the setting of the iva2 boot mode to idle. But as that register
seems to be there and is harmless if no iva2 is on the SoC, it's
probably safest to do the complete reset.

Acked-by: Mark A. Greer <mgreer@animalcreek.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

On OMAP platform, FIQ is reserved for secure environment only. If at all
the FIQ needs to be disabled, it involves going through security
API call. Hence the local_fiq_[enable/disable]() in the OMAP code is bogus.
On GP devices too, the fiq is disabled for non-secure software.

So just get rid of it.

Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

The text in Documentation said it would be removed in 2.6.41;
the text in the Kconfig said removal in the 3.1 release.  Either
way you look at it, we are well past both, so push it off a cliff.

Note that the POWER_CSTATE and the POWER_PSTATE are part of the
legacy tracing API.  Remove all tracepoints which use these flags.
As can be seen from context, most already have a trace entry via
trace_cpu_idle anyways.

Also, the cpufreq/cpufreq.c PSTATE one is actually unpaired, as
compared to the CSTATE ones which all have a clear start/stop.
As part of this, the trace_power_frequency also becomes orphaned,
so it too is deleted.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Based on earlier discussions[1] we attempted to find a suitable
location for the omap DMA header in commit 2b6c4e73 (ARM: OMAP:
DMA: Move plat/dma.h to plat-omap/dma-omap.h) until the conversion
to dmaengine is complete.

Unfortunately that was before I was able to try to test compile
of the ARM multiplatform builds for omap2+, and the end result
was not very good.

So I'm creating yet another all over the place patch to cut the
last dependency for building omap2+ for ARM multiplatform. After
this, we have finally removed the driver dependencies to the
arch/arm code, except for few drivers that are being worked on.

The other option was to make the <plat-omap/dma-omap.h> path
to work, but we'd have to add some new header directory to for
multiplatform builds.

Or we would have to manually include arch/arm/plat-omap/include
again from arch/arm/Makefile for omap2+.

Neither of these alternatives sound appealing as they will
likely lead addition of various other headers exposed to the
drivers, which we want to avoid for the multiplatform kernels.

Since we already have a minimal include/linux/omap-dma.h,
let's just use that instead and add a note to it to not
use the custom omap DMA functions any longer where possible.

Note that converting omap DMA to dmaengine depends on
dmaengine supporting automatically incrementing the FIFO
address at the device end, and converting all the remaining
legacy drivers. So it's going to be few more merge windows.

[1] https://patchwork.kernel.org/patch/1519591/#



cc: Russell King <linux@arm.linux.org.uk>
cc: Kevin Hilman <khilman@ti.com>
cc: "Benoît Cousson" <b-cousson@ti.com>
cc: Herbert Xu <herbert@gondor.apana.org.au>
cc: "David S. Miller" <davem@davemloft.net>
cc: Vinod Koul <vinod.koul@intel.com>
cc: Dan Williams <djbw@fb.com>
cc: Mauro Carvalho Chehab <mchehab@infradead.org>
cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
cc: David Woodhouse <dwmw2@infradead.org>
cc: Kyungmin Park <kyungmin.park@samsung.com>
cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
cc: Hans Verkuil <hans.verkuil@cisco.com>
cc: Vaibhav Hiremath <hvaibhav@ti.com>
cc: Lokesh Vutla <lokeshvutla@ti.com>
cc: Rusty Russell <rusty@rustcorp.com.au>
cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
cc: Afzal Mohammed <afzal@ti.com>
cc: linux-crypto@vger.kernel.org
cc: linux-media@vger.kernel.org
cc: linux-mtd@lists.infradead.org
cc: linux-usb@vger.kernel.org
cc: linux-fbdev@vger.kernel.org
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

arch/arm/mach-omap2/prcm.c and arch/arm/plat-omap/include/plat/prcm.h
are now completely unused and can be removed.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>

Most of the defines are specific to omap1 and omap2+,
and should be in the local headers. Only minimal function
prototypes need to be shared.

As discussed on linux-arm-kernel, we want to avoid
relative includes for the arch/arm/*omap* shared code:

http://www.spinics.net/lists/linux-omap/msg80520.html



So this patch re-adds a minimal plat/sram.h.

The new plat/sram.h must not be included from drivers,
that will break build for omap2+ CONFIG_MULTIPLATFORM.

Note that this patch temporarily adds two more
relative includes; Those will be removed in the
following patch.

Signed-off-by: Tony Lindgren <tony@atomide.com>

On OMAP34xx/35xx, and OMAP36xx chips with ES < 1.2, if the PER
powerdomain goes to OSWR or OFF while CORE stays at CSWR or ON, or if,
upon chip wakeup from OSWR or OFF, the CORE powerdomain goes ON before
PER, the UART3/4 FIFOs and McBSP2/3 SIDETONE memories will be
unusable.  This is erratum i582 in the OMAP36xx Silicon Errata
document.

This patch implements one of several parts of the workaround: the
addition of the wakeup dependency between the PER and WKUP
clockdomains, such that PER will wake up at the same time CORE_L3
does.

This is not a complete workaround.  For it to be complete:

1. the PER powerdomain's next power state must not be set to OSWR or
   OFF if the CORE powerdomain's next power state is set to CSWR or
   ON;

2. the UART3/4 FIFO and McBSP2/3 SIDETONE loopback tests should be run
   if the LASTPOWERSTATEENTERED bits for PER and CORE indicate that
   PER went OFF while CORE stayed on.  If loopback tests fail, then
   those devices will be unusable until PER and CORE can undergo a
   transition from ON to OSWR/OFF and back ON.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Move OMAP3xxx-specific CM functions & macros into cm3xxx.[ch] and
OMAP2xxx-specific macros into cm2xxx.[ch].  Move basic CM register
access functions into static inline functions in cm2xxx_3xxx.h,
leaving only OMAP2/3 hardreset functions in cm2xxx_3xxx.c.

As part of this, split the CM and hwmod code that waits for devices to
become ready into SoC-specific functions.

This is in preparation for the upcoming move of this code to drivers/.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Russ Dill <Russ.Dill@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

Move OMAP3xxx-specific PRM functions & macros into prm3xxx.[ch] and
OMAP2xxx-specific macros into prm2xxx.h.  (prm2xxx.c will be created
by a subsequent patch when it's needed.)  Move basic PRM register
access functions into static inline functions in prm2xxx_3xxx.h, leaving
only OMAP2/3 hardreset functions in prm2xxx_3xxx.c.

Also clarify the initcall function naming to reinforce that this code
is specifically for the PRM IP block.

This is in preparation for the upcoming powerdomain series and the
upcoming move of this code to drivers/.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Russ Dill <Russ.Dill@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

We want to remove plat/cpu.h. To do this, let's first split
it to private soc.h to mach-omap1 and mach-omap2. We have to
keep plat/cpu.h around until the remaining drivers are fixed,
so let's include the local soc.h in plat/cpu.h and for drivers
still including plat/cpu.h.

Once the drivers are fixed not to include plat/cpu.h, we
can remove the file.

This is needed for the ARM common zImage support.

[tony@atomide.com: updated to not print a warning]
Signed-off-by: Tony Lindgren <tony@atomide.com>

We can move this from plat to be local to plat-omap
for common ARM zImage support.

Signed-off-by: Tony Lindgren <tony@atomide.com>

Remove arch/arm/plat-omap/include/plat/sdrc.h by folding its contents
into arch/arm/mach-omap2/sdrc.h.  The objective is to assist Tony in
cleaning out arch/arm/plat-omap/, as his upstreams request.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
[tony@atomide.com: updated to remove rotate macros]
Signed-off-by: Tony Lindgren <tony@atomide.com>

Move plat/dma.h to plat-omap/dma-omap.h as part of single
zImage work

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Requirement of gpmc header outside of mach-omap2 has been
cutoff, move gpmc header file in plat-omap folder to local
mach-omap2 folder

Objective - common zImage participation of omap

Signed-off-by: Afzal Mohammed <afzal@ti.com>

This way we can remove includes of plat/gpio.h which won't work
with the single zImage support.

Note that we also remove the cpu_class_is_omap2() check
in gpio-omap.c as the drivers should not call it as we need to
make it local to arch/arm/mach-omap2 for single zImage support.

While at it, arrange the related includes in the standard way.

Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: linux-mtd@lists.infradead.org
Cc: alsa-devel@alsa-project.org
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Find and unwrap wrapped strings in the style:

	pr_debug("clockdomain: hardware cannot set/clear wake up of "
		 "%s when %s wakes up\n", clkdm1->name, clkdm2->name);

Keeping these strings contiguous seems to be the current Linux kernel
policy.

The offending lines were found with the following command:

    pcregrep -rnM '"\s*$\s*"' arch/arm/*omap*

While here, some messages have been clarified, some pr_warning(
... calls have been converted to pr_warn( ..., and some printk(KERN_*
... have been converted to pr_*.

Signed-off-by: Paul Walmsley <paul@pwsan.com>

This reverts commit 58f0829b.

Converstion to per-pwrdm per/post transition calls was a bit
premature.  Only tracking MPU, PER & CORE in the idle path means we
lose the accounting for all the other powerdomains which may also
transition in idle.  On OMAP3, due to autodeps, several powerdomains
transition along with MPU (e.g. DSS, USBHOST), and the accounting for
these was lost with this patch.  Since the accounting includes the
context loss counters, drivers for devices in those power domains
would never notice context lost, so would likely hang after any
off-mode transitions.

This patch should be revisited when the upcoming clkdm/pwrmdm/voltdm
use-counting seires is merged since then we can properly do accounting
without relying on a call in the idle path.

In addition, the original patch had another bug because the PER
powerdomain accounting was not updated until after the GPIO resume
hook is called.  Since gpio_resume_after_idle() checks the context
loss count (which is not yet updated) it would not properly restore
context, leaving the GPIO banks in an undefined state.

Cc: Jean Pihet <jean.pihet@newoldbits.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Reported-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

commit e7410cf7 (OMAP3: PM: move device-specific special cases from PM
core into CPUidle) moved mangement of cam_pwrdm to CPUidle but left
some remnants behind, namely the call to clkcm_allo_idle() for the
clockdomains in the MPU pwrdm.  Remove these since they are not
necessary and cause unwanted latency in the idle path.

Acked-by: Tero Kristo &lt;Tero Kristo <t-kristo@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

We only need to call the pre/post transtion methods when we know the
power state is changing.  First, split up the pre/post transition
calls to be per-powerdomain, and then make them conditional on whether
the power domain is actually changing states.

Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Iteration over all power domains in the idle path is unnecessary since
only power domains that are transitioning need to be accounted for.
Also PRCM register accesses are known to be expensive, so the
additional latency added to the idle path is signficiant.

In order allow the pre/post transitions to be isolated and called
per-pwrdm, change the API so passing in a specific power domain will
trigger the pre/post transtion accounting for only that specific power
domain.  Passing NULL means iterating over all power domains as is
current behavior.

Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

As IO Daisy chain sequence is triggered via hwmod mux, there is no need to
control it from cpuidle path for OMAP3.

Also as omap3_disable_io_chain is no longer being used, just remove the
function.

Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Since IO Daisychain modifies only PRM registers, it makes sense to move
it to PRM File. Also changed the timeout value for IO chain enable to
100us and added a wait for status disable at the end.

Thanks to Nishanth Menon <nm@ti.com> for contributing a fix to the
timeout code waiting for WUCLKOUT to go high.

Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Reviewed-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: renamed omap3_trigger_io_chain() to better describe the
 end result and to match other PRM functions; removed
 omap3_disable_io_chain(); moved MAX_IOPAD_LATCH_TIME to prcm-common as it
 will also be used by the OMAP4 code; removed unnecessary barrier;
 added kerneldoc; added credit for fix from Nishanth]
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Currently the enabling and disabling of IO Daisy chain is not
according to the TRM. The below steps are followed to enable/
disable the IO chain, based loosely on the "Sec 3.5.7.2.2
I/O Wake-Up Mechanism" section in OMAP3630 Public TRM[1].

Steps to enable IO chain:
[a] Set PM_WKEN_WKUP.EN_IO bit
[b] Set the PM_WKEN_WKUP.EN_IO_CHAIN bit
[c] Poll for PM_WKST_WKUP.ST_IO_CHAIN.
[d] When ST_IO_CHAIN bit set to 1, clear PM_WKEN_WKUP.EN_IO_CHAIN
[e] Clear ST_IO_CHAIN bit.

Steps to disable IO chain:
[a] Clear PM_WKEN_WKUP.EN_IO_CHAIN bit
[b] Clear PM_WKEN_WKUP.EN_IO bit
[c] Clear PM_WKST_WKUP.ST_IO bit by writing 1 to it.

Step [e] & [c] in each case can be skipped, as these are handled
by the PRCM interrupt handler later.

[1] http://focus.ti.com/pdfs/wtbu/OMAP36xx_ES1.x_PUBLIC_TRM_vV.zip



Signed-off-by: Mohan V <mohanv@ti.com>
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
[paul@pwsan.com: modified commit message to clarify that these steps are
 based loosely on the TRM section, rather than documented exactly]
Reviewed-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: resolved new warnings from checkpatch]
Signed-off-by: Paul Walmsley <paul@pwsan.com>

prcm_setup_regs() blindly accesses IVA bits
in the PRM and calls omap3_iva_idle() which
does more IVA related register accesses.
Only do this if the IVA hardware actually
exists.

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

By default, request_irq() will auto-enable the requested IRQ.

For PRCM interrupts, we may want to avoid that until the PM core code
is fully ready to handle the interrupts.  This is particularily true
for IO pad interrupts on OMAP3, which are shared between the hwmod
core and the PRM core.

In order to avoid PRCM IO-chain interrupts until the PM core is ready
to handle them, ready, set the IRQ_NOAUTOEN flag for the PRCM IO-chain
interrupt,  which means it will remain disabled after request_irq().

Then, explicitly enable the PRCM interrupts after the request_irq() in
the PM core (but not in the hwmod core.)

Special thanks to Tero Kristo for suggesting to isolate the fix to
only the IO-chain interrupt on OMAP3 instead of all PRCM interrupts.

Cc: Tero Kristo <t-kristo@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>

Resolve some warnings identified by cppcheck in arch/arm/mach-omap2:

    [arch/arm/mach-omap2/usb-tusb6010.c:129]: (style) Checking if unsigned variable 'tmp' is less than zero.
    [arch/arm/mach-omap2/prm_common.c:241]: (error) Possible null pointer dereference: irq_setup - otherwise it is redundant to check if irq_setup is null at line 247
    [arch/arm/mach-omap2/pm34xx.c:790]: (style) Variable 'per_clkdm' is assigned a value that is never used
    [arch/arm/mach-omap2/pm34xx.c:790]: (style) Variable 'core_clkdm' is assigned a value that is never used
    [arch/arm/mach-omap2/pm24xx.c:185]: (style) Variable 'only_idle' is assigned a value that is never used
    [arch/arm/mach-omap2/mux.c:254]: (error) Possible null pointer dereference: mux
    [arch/arm/mach-omap2/mux.c:258]: (error) Possible null pointer dereference: mux
    [arch/arm/mach-omap2/gpmc-onenand.c:178]: (style) Variable 'tick_ns' is assigned a value that is never used
    [arch/arm/mach-omap2/gpio.c:56]: (error) Possible null pointer dereference: pdata - otherwise it is redundant to check if pdata is null at line 57
    [arch/arm/mach-omap2/devices.c:45]: (style) Variable 'l' is assigned a value that is never used
    [arch/arm/mach-omap2/board-omap3evm.c:641] -> [arch/arm/mach-omap2/board-omap3evm.c:639]: (style) Found duplicate branches for if and else.
    [arch/arm/mach-omap2/am35xx-emac.c:95]: (style) Variable 'regval' is assigned a value that is never used
    [arch/arm/mach-omap2/devices.c:74]: (style) Variable 'l' is assigned a value that is never used
    [arch/arm/mach-omap2/pm34xx.c:277]: (style) Variable 'per_prev_state' is assigned a value that is never used
    [arch/arm/plat-omap/dmtimer.c:352]: (error) Possible null pointer dereference: timer - otherwise it is redundant to check if timer is null at line 354
    [arch/arm/plat-omap/omap_device.c:478]: (style) Variable 'c' is assigned a value that is never used
    [arch/arm/plat-omap/usb.c:42]: (style) Variable 'status' is assigned a value that is never used
    [arch/arm/mach-omap1/clock.c:197]: (style) Variable 'dpll1_rate' is assigned a value that is never used
    [arch/arm/mach-omap1/lcd_dma.c:60]: (style) struct or union member 'lcd_dma_info::size' is never used
    [arch/arm/mach-omap1/pm.c:572]: (style) Variable 'entry' is assigned a value that is never used

Some of them are pretty good catches, such as gpio.c:56 and
usb-tusb6010.c:129.

Thanks to Jarkko Nikula for some comments on the sscanf() warnings.
It seems that the kernel sscanf() ignores the field width anyway for the
%d format, so those changes have been dropped from this second version.

Thanks to Daniel Marjamäki <daniel.marjamaki@gmail.com> for pointing
out that a variable was unnecessarily marked static in the
board-omap3evm.c change.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Cc: Charulatha Varadarajan <charu@ti.com>
Cc: Daniel Marjamäki <daniel.marjamaki@gmail.com>
Cc: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Charulatha Varadarajan <charu@ti.com> # for gpio.c

Disintegrate asm/system.h for ARM.

Signed-off-by: David Howells <dhowells@redhat.com>
cc: Russell King <linux@arm.linux.org.uk>
cc: linux-arm-kernel@lists.infradead.org

Currently, pm34xx.c has a mix of printk() and pr_*() statements
so replace the printk() statements with the equivalent pr_*()
statements.

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

It appears that the error paths were overlooked when the
omap3_pm_init() routine had the prcm chain handler code
added.  Fix this by adding a goto target and reordering
the error handling code.  Also fix how the irq argument
for free_irq() is determined.

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

The platform_suspend_ops can be shared across OMAP2, 3, and 4, along
with all of the functions referenced in that structure.  This patch
shares them.  It also removes the suspend_state file-scoped variable
in the OMAP2 and 3 PM code; it does not appear to be actually needed
by anything.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
[khilman@ti.com: minor rework needed due to rebase/merge with conflicting changes]
Signed-off-by: Kevin Hilman <khilman@ti.com>

clkdms_setup() is identical across OMAP2, 3, and 4, so share it.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Remove some superfluous calls to pwrdm_clear_all_prev_pwrst().
pwrdm_pre_transition(), which appears a few lines after these calls,
invokes pwrdm_clear_all_prev_pwrst() on each powerdomain -- there's no
need to do it twice.

N.B.: some of us have observed that accesses to the previous
powerstate registers seem to be quite slow.  Although the writes
removed by this patch should be buffered by the write buffer, there is
a read to a PRM register immediately afterwards.  That will block the
OMAP3 MPU until all of those writes complete.  So this patch should
result in a minor performance improvement during idle entry.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Tero Kristo <t-kristo@ti.com>
[khilman@ti.com: removed a couple more for OMAP4]
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Modify omap_gpio_prepare_for_idle() & omap_gpio_resume_after_idle() functions
to handle save context & restore context respectively in the OMAP GPIO driver
itself instead of calling these functions from pm specific files.
For this, in gpio_prepare_for_idle(), call *_get_context_loss_count() and in
gpio_resume_after_idle() call it again. If the count is different, do restore
context.

Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Signed-off-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>

PM interrupt handling is now done through the PRCM chain handler. The
interrupt handling logic is also split in two parts, to serve IO and
WKUP events separately. This allows us to handle IO chain events in a
clean way.

Core event code is also changed in accordance to this, as PRCM
interrupt handling is done by independent handlers, and the core
handler should not clear the IO events anymore.

Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
[paul@pwsan.com: use pr_err(); combined with portions of earlier patches and
 the "do not enable PRCM MPU interrupts manually" patch]
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Omap_uart_can_sleep function blocks system wide low power state until
uart is active remove this func and add qos requests to prevent
MPU from transitioning.

Keep qos request to default value which will allow MPU to transition
and while uart baud rate is available calculate the latency value
from the baudrate and use the same to hold constraint while uart clocks
are enabled, and if uart is auto-idled the constraint is updated with
default constraint value allowing MPU to transition.

Qos requests are blocking notifier calls so put these requests to
work queue, also the driver uses irq_safe version of runtime API's
and callbacks can be called in interrupt disabled context.
So to avoid warn on slow path warning while using qos update
API's from runtime callbacks use the qos_work_queue.

During bootup the runtime_resume call backs might not be called and runtime
callback gets called only after uart is idled by setting the autosuspend
timeout. So qos_request from runtime resume callback might not activated during
boot if uart baudrate is calculated during bootup for console uart, so schedule
the qos_work queue once we calc_latency while configuring the uart port.

Flush and complete any pending qos jobs in work queue while suspending.

Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>

In preparation to UART runtime conversion remove uart specific calls
from pm24xx/34xx files and their definition from serial.c
These func calls will no more be used with upcoming uart runtime design.

1.) omap_uart_prepare_suspend :- can be taken care with driver suspend hooks.
2.) omap_uart_enable_irqs :- Used to enable/disable uart irq's in suspend
    path from PM code, this is removed as same is handled by
    uart_suspend_port/uart_resume_port in omap-serial driver which will
    do an port_shutdown on suspend freeing irq and port_startup on resume
    enabling back irq.
3.) Remove prepare_idle/resume_idle calls used to gate uart clocks.
    UART clocks can be gated within driver using runtime funcs
    and be woken up using irq_chaining from omap_prm driver.
4.) Remove console_locking from idle path as clock gating is done withing
    driver itself with runtime API. Remove is_suspending check used to acquire
    console_lock.

Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

As suggested by Russell King - ARM Linux <linux@arm.linux.org.uk>,
there's no need to keep local prototypes in non-local headers.

Add mach-omap1/common.h and mach-omap2/common.h and move the
local prototypes there from plat/common.h and mach/omap4-common.h.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Based on the documents that I have here, there doesn't appear to be an
equivalent to erratum i443 for OMAP3630, so restrict this one to OMAP34xx
chips.

Also, explicitly restrict this erratum to EMU and HS devices.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>