The Itead Ibox is a multi board device based on the Allwinner A20 SoC.
It contains the A20 Itead Core module and a base board for the external
interfaces.

The core module comes with 4GB NAND and 1GB DDR RAM.

The base board to which the core board is connected provides 3 USB 2.0 Host
ports, 1 USB 2.0 OTG, 1 uSD slot, 10/100 Ethernet port, HDMI, IR receiver,
SPDIF and a 32-pin GPIO header. This header expands the features of core
board by exposing the VGA pins, audio In/Out pins, SATA, SPI, I2C, UARTS,
USB-OTG and power.

Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Itead have a core module board that can be populated with either
an Allwinner A10 or A20 SoC. This patch creates a common dtsi
which these boards can use.

Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

mmc2 has a special pin for eMMC hardware reset, which is controllable
from the controller. Add the "mmc-cap-hw-reset" property to denote that
this controller supports this function, and the pins are actually used.

Also increase the signal drive strength for mmc2 pins, for HS-DDR mode
support.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

mmc2 has a special pin for eMMC hardware reset, which is controllable
from the controller. Add the "mmc-cap-hw-reset" property to denote that
this controller supports this function, and the pins are actually used.

Also increase the signal drive strength for mmc2 pins, for HS-DDR mode
support.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

mmc2_8bit_pins is used with eMMC chips, which also have a reset pin.
The MMC controller also has a reset output that is supported.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

mmc2_8bit_pins is used with eMMC chips, which also have a reset pin.
The MMC controller also has a reset output that is supported.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

According to Allwinner, only mmc3 supports 8 bit DDR transfers for eMMC.
Switch to mmc3 for the onboard eMMC, and also assign vqmmc for signal
voltage sensing, and "cap-mmc-hw-reset" to denote this instance can use
eMMC hardware reset.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

mmc2 and mmc3 are available on the same pins, with different mux values.
However, only mmc3 supports 8 bit DDR transfer modes.

Since preference for mmc3 over mmc2 is due to DDR transfer modes, just
set the drive strength to 40mA, which is needed for DDR.

This pinmux setting also includes the hardware reset pin for emmc.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

sun9i/A80 MMC controllers have a larger FIFO, and the FIFO DMA
trigger levels can be increased. Also, the mmc module clock parent
has a higher clock rate, and the sample and output delay phases
are different.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

mmc2 has a special pin for eMMC hardware reset, which is controllable
from the controller. Add the "mmc-cap-hw-reset" property to denote that
this controller supports this function, and the pins are actually used.

Also increase the signal drive strength for mmc2 pins, for HS-DDR mode
support.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The current DT doesn't have a phandle to the CPU regulator in the CPU node,
which disables the CPU voltage scaling entirely.

Add that phandle.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Cubietruck Plus is a A83T/H8 based development board. The board has
standard DDR3 SDRAM, AXP818 PMIC/codec, SD/MMC, eMMC, USB 2.0 host
via HSIC USB Hub, USB OTG, SATA via USB bridge, gigabit ethernet,
WiFi, headphone out / mic in, and various GPIO headers.

The board also has an EEPROM on i2c0 which holds the MAC address.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The A83T, like previous Allwinner SoCs, has a watchdog as part of its
timer block. Add a device node for it.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

A83T timer is compatible with that of earlier SOCs.
Just add timer node to enable and re-use it.

Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

H8Homlet Proto v2.0 Board is A83T Dev Board by Allwinner.
It has UART, ethernet, USB, HDMI, etc ports on it.

A83T patches are tested on this board.
It has UART, ethernet, USB, HDMI, etc ports on it.

For FEL mode it needs USB A-A(Male) cable. I used uart0 which
is multiplexed to microsd pins PF2 and PF4.

Enabled UART0 Header(PB9, PB10 pins).

Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Allwinner A83T is new octa-core cortex-a7 SOC.
This adds the basic dtsi, the clocks differs from
earlier sun8i SOCs.

Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
[Maxime: Removed empty chosen node]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add a node describing the focaltech ft5306de4 touchscreen found on
inet97fv2 tablets.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add a node describing the focaltech ft5306de4 touchscreen found on
chuwi-v7-cw0825 tablets.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add a node describing the focaltech ft5406ee8 touchscreen found on
inet-9f-rev03 / qware qw tb-g100 tablets.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

On r8a7740/armadillo, actual clock rates are ca. 4% lower than reported
by /sys/kernel/debug/clk/clk_summary. Correct the extal1 frequency from
25 MHz to 24 MHz to fix this.

This matches the Armadillo-800 EVA Product Manual, which claims the main
crystal runs at 24 MHz, and the old legacy/reference board code.

Fixes: 25aa7ba3 ("ARM: shmobile: armadillo800eva: Sync DTS")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Enable PCIe DT node and fill PCIe DT node with regulator, pinctrl and reset
GPIO, to use the PCIe on the ifc6410 board.

Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Add the PCIe DT node so that it can probe and be used.

Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

The device tree version of Versatile AP/PB never had LED support
so we are missing LEDs from our hardware boards. Add this as
syscon LEDs like we did for Integrator and Juno. We need to
spawn devices in the syscon with "simple-mfd" for this to work.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

According to datasheet, the registers space of SDHC controller is 1Kb,
not '0x1000', the correct value should be '0x400'. Bracket interrupt
numbers individually per recommendations.

Signed-off-by: Roman Volkov <rvolkov@v1ros.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Since WM8650 has the same 'WMT' SDHC controller as WM8505, and the driver
is already in the kernel, this node enables the controller support for
WM8650

Signed-off-by: Roman Volkov <rvolkov@v1ros.org>
Reviewed-by: Alexey Charkov <alchark@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Commit 0976c946
"arm/versatile: Fix versatile irq specifications"
has an off-by-one error on the Versatile AB that has
been regressing the Versatile AB hardware for some time.

However it seems like the interrupt assignments have
never been correct and I have now adjusted them according
to the specification. The masks for the valid interrupts
made it impossible to assign the right SIC interrupt
for the MMCI, so I went in and fixed these to correspond
to the specifications, and added references if anyone
wants to double-check.

Due to the Versatile PB including the Versatile AB
as a base DTS file, we need to override and correct
some values to correspond to the actual changes in the
hardware.

For the Versatile PB I don't think the IRQ line
assignment for MMCI has ever been correct for either of
the two MMCI blocks. It would be nice if someone with the
physical PB board could test this.

Patch tested on the Versatile AB, QEMU for Versatile AB
and QEMU for Versatile PB.

Cc: Rob Herring <robh@kernel.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: stable@vger.kernel.org
Fixes: 0976c946 ("arm/versatile: Fix versatile irq specifications")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

The Nomadik has sporadic crashes because of these latencies, setting
them to max makes the platform work nicely, so use this values for
now.

These latencies were set to 2 since the Nomadik platform was merged,
but I suspect they never took effect until the right size and
associativity for the cache was specified in the device tree and
that is why the crash comes now.

Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

The pinctrl group ipu2grp is a leftover from the previous iomuxc DT
cleanup.  It's not used by anyone now.  More importantly, it's getting
in the way of saving the unnecessary pinfunc container node from the
board dts files that include imx6q.dtsi.

Let's clean it up.

Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Tested-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

As of commit e488ca9f ("doc: dt: mtd: partitions: add compatible
property to "partitions" node"), the "partitions" subnode of an SPI
FLASH device node must have a compatible property. The partitions are no
longer detected if it is not present.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

As of commit e488ca9f ("doc: dt: mtd: partitions: add compatible
property to "partitions" node"), the "partitions" subnode of an SPI
FLASH device node must have a compatible property. The partitions are no
longer detected if it is not present.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

As of commit e488ca9f ("doc: dt: mtd: partitions: add compatible
property to "partitions" node"), the "partitions" subnode of an SPI
FLASH device node must have a compatible property. The partitions are no
longer detected if it is not present.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

As of commit e488ca9f ("doc: dt: mtd: partitions: add compatible
property to "partitions" node"), the "partitions" subnode of an SPI
FLASH device node must have a compatible property. The partitions are no
longer detected if it is not present.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

As of commit e488ca9f ("doc: dt: mtd: partitions: add compatible
property to "partitions" node"), the "partitions" subnode of an SPI
FLASH device node must have a compatible property. The partitions are no
longer detected if it is not present.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

As of commit e488ca9f ("doc: dt: mtd: partitions: add compatible
property to "partitions" node"), the "partitions" subnode of an SPI
FLASH device node must have a compatible property. The partitions are no
longer detected if it is not present.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

With this patch we add the watchdog node in the meson8b DTS file.

Signed-off-by: Carlo Caione <carlo@endlessm.com>

Add the blue status LED to the Hardkernel Odroid C1 board DTS.

Signed-off-by:  <edward.cragg@codethink.co.uk>
Signed-off-by: Carlo Caione <carlo@endlessm.com>

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

These will be used for enabling UART1, SPI1, and SPI2.

Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

The Pi 2 B ends up like a Pi 1 B+, with the same peripherals and
pinout, but the CPU and memory layout changed to use the 2836.

Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

For Raspberry Pi 2, we want to use the same general pin assignment
bits, but need to use bcm2836.dtsi for the CPU instead.

Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>