GPIO modules are also interrupt sources. However, they require both the
GPIO number and IRQ type to function properly.

By declaring that GPIO uses interrupt-cells=<1>, we essentially do not
allow users of the nodes to use the interrupt property appropritely.

With this change, the following now works:

interrupt-parent = <&gpio6>;
interrupts = <5 IRQ_TYPE_LEVEL_LOW>;

Fixes: 6e58b8f1 ('ARM: dts: DRA7: Add the dts files for dra7 SoC and dra7-evm board')
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

For v3.14 and prior, 1-bit Hamming code ECC via software was used
for NAND on this board.
Commit c06c5270 in v3.15 changed the behaviour
to use 1-bit Hamming code via Hardware using a different ECC layout
i.e. (ROM code layout) than what is used by software ECC.

This ECC layout change causes NAND filesystems created in v3.14
and prior to be unusable in v3.15 and later. So revert back to
using software ECC scheme.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

On r8a7791, i2c6 (aka iic3) doesn't need pinmux, but the koelsch dts
refers to non-existent pinmux configuration data:

pinmux core: sh-pfc does not support function i2c6
sh-pfc e6060000.pfc: invalid function i2c6 in map table

Remove it to fix this.

Fixes: commit 1d41f36a ("ARM: shmobile:
       koelsch dts: Add VDD MPU regulator for DVFS")

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Olof Johansson <olof@lixom.net>

Working on Gigabit/PCIe support in U-Boot for Apalis T30 I realised
that the current device tree source includes for our modules only
happen to work due to referencing the on-carrier 5v0 supply from USB
which is not at all available on-module. The modules actually contain
TPS60150 charge pumps to generate the PMIC required 5 volts from the
one and only 3.3 volt module supply. This patch fixes this.

(Note: When back-porting this to v3.16 stable releases, simply drop the
change to tegra30-apalis.dtsi; that file was added in v3.17)

Cc: <stable@vger.kernel.org> #v3.16+
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

During the restructuring of the Rockchip Cortex-A9 dtsi files it seems
like the pinctrl settings vanished at some point from the mmc0 support.

This of course renders them unusable, so readd the necessary pinctrl
properties.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Increase max i2c bus frequency beyond the default for faster
data transfers. According to the manual, these faster speeds are
only available when the board is wired up the right way. In this case,
the vendor kernel has run at this speed for a long time.

sda-delay is needed for talking to RTC on PMIC, otherwise the i2c
controller never sees an ACK. Strangely the other PMIC i2c slave (the
main one) works fine even without this delay. I Chose value 100 to
match the vendor kernel.

Signed-off-by: Daniel Drake <drake@endlessm.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Tested-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

The ODROID kernel shows that the PMIC interrupt line is hooked up
to pin GPX3-2.

This is needed for the max77686-irq driver to create the PMIC IRQ
domain, which is needed by max77686-rtc.

Signed-off-by: Daniel Drake <drake@endlessm.com>
Tested-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

The current pinfunc define all uart CTS_B IO port for DCE uart 'CTS_B'
IP port. Since uart IP port 'CTS_B' is output, and it don't need to
set 'SELECT_INPUT' bit.

Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

The VPU on i.MX53 has two distinct clocks for register access and
internal function.

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Fixes: fbf970f6 ("ARM: dts: mx53qsb: Enable VPU support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

Signed-off-by: Silvio Fricke <silvio.fricke@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

Previous version had an extra 'fsl' which made the pins not match
any entry.  The console message,

 vf610-pinctrl 40048000.iomuxc: no fsl,pins property in node \
    /soc/aips-bus@40000000/iomuxc@40048000/vf610-twr/esdhc1grp

is displayed without the fix.  The prior version would generally
work as u-boot sets the pins properly for sdhc.  This change allows
Linux sdhc use even if u-boot is built without sdhc support.

Signed-off-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Fixes: 0517fe6a ("ARM: dts: vf610-twr: Add support for sdhc1")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>

This was caused by commit 5a8da524 ("ARM: dts: exynos5420: add dsi
node"), which conflicted with d51cad7d ("ARM: dts: remove display
power domain for exynos5420").

The DTS addition should never have been merged through the DRM tree in
the first place, and it lacked an ack from the platform maintainer
(who would have known that the disp_pd reference got removed).

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Olof Johansson <olof@lixom.net>

The EHCI and HSIC device tree nodes were added in the wrong place.
Fix them.

Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Olof Johansson <olof@lixom.net>

This patch adds common part of dsi node.

Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

This patch adds mipi-phy node for MIPI DSI device.

Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

This patch adds sysreg property to fimd device node
which is required to use I80 interface.

Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

This patch adds sysreg property to fimd device node
which is required to use I80 interface.

Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

This patch adds socfpga Ethernet filter attributes for multicast
and unicast filters per Synopsys Ethernet IP configuration chosen
by Altera for the Cyclone 5 and Arria SOC FPGAs.

Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use CPU_METHOD_OF_DECLARE() instead. And declare smp method in dts file.

Changelog:
v6:
  * Use hisilicon,hi3620-smp as enable-method property in Hi3620 dts.

Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: Wei Xu <xuwei5@hisilicon.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Add dts file for Hisilicon x5hd2 development kit board.

Signed-off-by: Haifeng Yan <yanhaifeng@gmail.com>
Signed-off-by: Jiancheng Xue <jchxue@gmail.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: Wei Xu <xuwei5@hisilicon.com>
[olof: Rename dts/dtsi to include hisi prefix]
Signed-off-by: Olof Johansson <olof@lixom.net>

This is the top USB port on the evb (the one closest to the Ethernet
connector).

Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

rk3288 has two kind of usb controller; this adds the ehci variant for
host0 and hsic.

At the moment we don't add any phys for these controllers, but the
default settings seem to work OK.

There is a hardware problem in ohci controller which make it
unavailable and host0 controller can only support high-speed devices.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

There is no phy driver that works on the Rockchip board for either USB
host port yet.  For now just hardcode the vbus signal to be on all the
time which makes both the dwc2 host and the EHCI port work.

Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Working on sound support I noticed the Apalis T30 Evaluation board
device tree missing the more generic Apalis T30 compatible string.

Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Indentation of the clock property used a hodgepodge of tabs and spaces.
Make them more consistent (tabs for indentation followed by spaces for
alignment).

Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

The GPIO pin connected to card detect was inverted twice: once by
the argument to the GPIO line itself where it was magically marked
as active low by the flag GPIO_ACTIVE_LOW (0x01) in the third cell,
and also marked active low AGAIN by explicitly stating
"cd-inverted" (a deprecated method).

After commit 78f87df2
"mmc: mmci: Use the common mmc DT parser" this results in the
line being inverted twice so it was effectively uninverted, while
the old code would not have this effect, instead disregarding the
flag on the GPIO line altogether, which is a bug. I admit the
semantics may be unclear but inverting twice is as good a
definition as any on how this should work.

So fix up the buggy device tree. Use proper #includes so the DTS
is clear and readable.

Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

This adds the Designware compatible watchdog found on RK3xxx Cortex-A9 SoCs.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>

We set default pinctrl settings for the uarts in rk3188.dtsi already,
so remove forgotten duplicate.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>

This patch add missing pinctrl for uart0/1 for Exynos3250. The gpio pin (
uart0_data, uart0_fctl, uart1_data) is only used for UART IP.

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This patch removes duplicat 'interrupt-parent' property for Exynos3250
because exynos3250.dtsi already defined 'interrupt-parent' property
as following:

In arch/arm/boot/dts/exynos3250.dtsi:

	compatible = "samsung,exynos3250";
	interrupt-parent = <&gic>;

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This patch add TMU (Thermal Management Unit) dt node to monitor the high
temperature for Exynos3250.

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

The IRQB interrupt pin of MAX77686 PMIC is connected to GPX3[2] pin of
Exynos5250 on the Exynos5250 SMDK board. Specify this connection using
interrupts property for the max77686 pmic node.

Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Move it from exynos5250-cros-common.dtsi to exynos5250-snow.dts.
Spring does not need it, it uses an Atmel maXTouch instead.

Signed-off-by: Andreas Faerber <afaerber@suse.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Move it from exynos5250-cros-common.dtsi to exynos5250-snow.dts.
Spring does not need it, it uses an s5m8767 instead.

Signed-off-by: Andreas Faerber <afaerber@suse.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Commit 9188883f (ARM: dts: Enable twl4030 off-idle configuration
for selected omaps) allowed n900 to cut off core voltages during
off-idle. This however caused a regression where twl regulator
vaux1 was not getting enabled for the LCD panel as we are not
requesting it for the panel.

Turns out quite a few devices on n900 are using vaux1, and we need
to either stop idling it, or add proper regulator_get calls for all
users. But until we have a proper solution implemented and tested,
let's just disable the twl off-idle configuration for now for n900.

Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Fixes: 9188883f (ARM: dts: Enable twl4030 off-idle configuration for selected omaps)
Signed-off-by: Tony Lindgren <tony@atomide.com>

The DMA engine is enabled for all DTs that derive from zynq-7000.dtsi.
There is no need to override the 'status' property in board DTs.

Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Add node describing Zynq's CAN controller.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Soren Brinkmann <soren.brinkmann@xilinx.com>

Adds PMU DT node for exynos5260 SoC.

Signed-off-by: Vikas Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Exynos initialization code now relies on obtaining the PMU address,
so prepare a PMU node for Exynos5410.

Fixes: fce9e5bb ("ARM: EXYNOS: Add support for mapping PMU base
address via DT")

Signed-off-by: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Update the bindings for touchscreen size.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>