Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

Add a DTS describing the Digilent ZYBO board. Similar to ZED but with
a 50MHz crystal instead of 33MHz.

Acked-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

This patch adds new board dts file to support Samsung Monk board which
is based on Exynos3250 SoC and has different H/W configuration from
Rinato.

This dts file support following features:
- eMMC
- Main PMIC (Samsung S2MPS14)
- Interface PMIC (Maxim MAX77836, MUIC, fuel-gauge, charger)
- RTC of Exynos3250
- ADC of Exynos3250 with NTC thermistor
- I2S of Exynos3250
- TMU of Exynos3250
- Secure firmware for Exynos3250 secondary cpu boot
- Serial ports of Exynos3250
- gpio-key for power key

Signed-off-by: Youngjun Cho <yj44.cho@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

The A80 Optimus Board is was launched with the Allwinner A80 SoC.
It was jointly developed by Allwinner and Merrii.

This board has a UART port, a JTAG connector, USB host ports, a USB
3.0 OTG connector, an HDMI output, a micro SD slot, 8G NAND flash,
4G DRAM, a camera sensor interface, a WiFi/BT combo chip, a headphone
jack, IR receiver, and additional GPIO headers.

This patch adds only basic support.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Andreas Färber <afaerber@suse.de>

This adds support for the Olimex A20-OLinuXino-Lime2
https://www.olimex.com/Products/OLinuXino/A20/A20-OLinuXIno-LIME2



Differences to previous Lime boards are 1GB RAM and gigabit ethernet

Signed-off-by: Iain Paton <ipaton0@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Mele M3 is yet another Allwinnner based Android top set box from Mele.

It uses a housing similar to the A2000, but without the USM sata storage slot
at the top.

It features an A20 SoC, 1G RAM, 4G eMMC (unique for Allwinner devices),
100Mbit ethernet, HDMI out, 3 USB A receptacles, VGA, and A/V OUT connections.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Banana Pi is an A20 based development board using Raspberry Pi compatible
IO headers. It comes with 1 GB RAM, 1 Gb ethernet, 2x USB host, sata, hdmi
and stereo audio out + various expenansion headers:

http://www.lemaker.org/



Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add Colibri VF50 device tree files vf500-colibri.dtsi and
vf500-colibri-eval-v3.dts, in line with the Colibri VF61 device tree
files. However, to minimize dupplication we also add vf-colibri.dtsi
and vf-colibri-eval-v3.dtsi which contain the common device tree
nodes.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The LS1021A TWR is a low cost, high-performance evaluation,
development and test platform supporting the LS1021A processor.
It is optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.

For more detail information about the LS1021A TWR board, please
refer to LS1021A QorIQ Tower System Reference Manual.

Signed-off-by: Chao Fu <B44548@freescale.com>
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The LS1021A QorIQ development system (QDS) is a high-performance
computing evaluation, development and test platform supporting
the LS1021A processor. The LS1021A QDS is optimized to support
the high-bandwidth DDR3LP/DDR4 memory and a full complement of
high-speed SerDes ports.

For more detail information about the LS1021AQDS, please refer to
the QorIQ LS1021A Development System Reference Manual.

Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Chao Fu <B44548@freescale.com>
Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

TBS2910 is a i.MX6Q based board. For additional details refer to
http://www.tbsdtv.com/products/tbs2910-matrix-arm-mini-pc.html



Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Synology DS414 is a 4-bay NAS powered by a Marvell Armada XP
(mv78230 dual-core @1.33Ghz). It is very similar on many aspects
to previous 4-bay synology models based on Marvell kirkwood SoC.
Here is a short summary of the device:

 - 1GB RAM
 - Boot on SPI flash (64Mbit Micron N25Q064)
 - 2 GbE interfaces (Armada MAC connected to two Marvell 88E1512
   PHY via RGMII)
 - 1 front USB 2.0 ports (directly handled by the Armada 370)
 - 2 rear USB 3.0 ports (handled by an EtronTech EJ168A XHCI
   controller on the PCIe bus)
 - 4 internal SATA ports handled by a Marvell 88SX7042 SATA-II
   controller on the PCIe bus)
 - Seiko S-35390A I2C RTC chip
 - UART0 providing serial console
 - UART1 used for poweroff (connected to a Microchip PIC16F883)

Additional note: the front LEDs the and the two fans are not directly
connected to the SoC and under its control. The former are presumably
driven by the SATA controller, the latter by the PIC.

[ jac: fixed up s/ge[01]_rgmii_pins/pmx_ge[01]_rgmii/ to match
armada-xp.dtsi ]

Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/5b678d6d1f2f42f4bf0d087878b9d8024d463ea7.1416613429.git.arno@natisbad.org


Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Synology DS213j is a 2-bay NAS powered by a Marvell Armada 370
(88F6710 @1.2Ghz). It is very similar on many aspects to previous
2-bay synology models based on Marvell kirkwood SoC. Here is a
short summary of the device:

 - 512MB RAM
 - boot on SPI flash (64Mbit Micron N25Q064)
 - 1 GbE interface (Armada MAC connected to a Marvell 88E1512
   PHY via SGMII)
 - 2 rear USB 2.0 ports (directly handled by the Armada 370)
 - 2 internal SATA ports handled by the Armada 370: 2 GPIO for
   presence, 2 for powering them
 - two front amber LED (disk1, disk2) controlled by the SoC
 - Seiko S-35390A I2C RTC chip
 - UART0 providing serial console
 - UART1 used for poweroff (connected to a TI MSP430F2111)
 - Fan handled via 4 GPIO (3 for speed, 1 for alarm)

Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/20f1a03897df1d825b62abdd525e588a8e39b3ec.1416613429.git.arno@natisbad.org


Signed-off-by: Jason Cooper <jason@lakedaemon.net>

This adds the NovaTech OrionLXm which is based on the AM335x SoC
http://www.novatechweb.com/substation-automation/orionlxm/



RAM: 512MiB
Flash: 4GB eMMC
Ethernet PHYs: 2x Micrel KSZ8041FTLI
USB ports are used internally by the expansion cards.
Internal micro SD slot is available.

Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The Arria 10 is latest SOC+FPGA from the Altera SOCFPGA platform. The Arria10
SOC shares some similarities with the SOCFPGA Cyclone5 and Arria5, but there
are enough differences to warrant a new base dtsi.

The differences are:
* 3 EMAC controllers
* 5 I2C controllers
* 3 SPI controllers
* 1.5 GHZ dual A9s
* Support for DDR4

Besides the usual memory map and IRQ changes, the clock framework will be
different, so this patch just adds the fixed-clocks.

Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>

The model B and B+ differ in the GPIO lines for ACT and PWR leds, and the
I2S interface.

Signed-off-by: Matthias Klein <matthias.klein@linux.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

The STiH410 is an advanced multi-HD AVC processor with 3D graphics acceleration
and 1.5-GHz ARM Cortex-A9 SMP CPU part of the stih407 family.

It has wide connectivity including USB 3.0, PCI-e, SATA and gigabit ethernet.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>

The mt6592-evb is an evaluation board based on the MT6592 SoC.

Signed-off-by: Howard Chen <ibanezchen@gmail.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>

This allows the "make dtbs" to build the moose and mt8135-evbp1
for MediaTek SoC

Signed-off-by: Joe.C <yingjoe.chen@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>

Add items in arch/arm/boot/dt/Makefile to compile the dtb
for mach-mmp.
Change the dts and dtsi file to use #include instead of \include\

Signed-off-by: Chao Xie <chao.xie@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

BeagleBoard-X15 is the next generation Open Source Hardware
BeagleBoard based on TI's AM5728 SoC featuring dual core 1.5GHz A15
processor. The platform features 2GB DDR3L (w/dual 32bit busses),
eSATA, 3 USB3.0 ports, integrated HDMI (1920x1080@60), separate LCD
port, video In port, 4GB eMMC, uSD, Analog audio in/out, dual 1G
Ethernet.

For more information, refer to:
BeagleBoard-X15 Wiki:
http://www.elinux.org/Beagleboard:BeagleBoard-X15

AM5728 is part of the Sitara product family whose additional details
will be available: http://www.ti.com/lsds/ti/arm/overview.page

Technical Reference Manual for AM5728 is public domain at:
http://www.ti.com/lit/spruhz6



Just add basic support for the moment, the following updates are needed:
  i)	Ethernet - depends on SoC dts fixes
  ii)	USB Client (USB2) - depends on GPIO extcon
  ii)	HDMI - additional driver fixes pending
  iii)	Audio - additional driver fixes pending

NOTE:
AM5728 Data Manual (SPRS915L - August 2014) section 4.1.1 states: "All
unused power supply balls must be supplied with the voltages specified
in the Section 5.2, Recommended Operating Conditions". This implies
that all unused voltage rails for AM5728 can never be switched off even
if the hardware blocks inside that voltage domain is unused. Switching
off these unused rails may result in stability issues on other domains
and increased leakage and power-on-hour impacts.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add support for the new hardware revision of the IGEPv2. Basically, the new
revision F replaces the old Wifi module for a Wilink8 based module.

Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add support for the new hardware revision of the IGEP COM MODULE. Basically,
the new revision G replaces the old Wifi module for a Wilink8 based module.

Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

DT files to enable cygnus consisting on reference designs
and cygnus core configuration.

Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Arun Parameswaran <aparames@broadcom.com>
Tested-by: Jonathan Richardson <jonathar@broadcom.com>
Reviewed-by: JD (Jiandong) Zheng <jdzheng@broadcom.com>
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

This patch adds support for device tree source for Samsung Rinato
board (Gear 2) based on Exynos3250 SoC.

This dts file support following features:
- eMMC
- Main PMIC (Samsung S2MPS14)
- Interface PMIC (Maxim MAX77836, MUIC, fuel-gauge, charger)
- RTC of Exynos3250
- ADC of Exynos3250 with NTC thermistor
- I2S of Exynos3250
- TMU of Exynos3250
- MFC of Exynos3250
- Secure firmware for Exynos3250 secondary cpu boot
- Serial ports of Exynos3250
- gpio-key for power key

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This patch adds initial support for the Marsboard RK3066. It enables
EMAC Rockchip which is the ethernet support on the board and registers
it as a supported rockchip platform.

Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add a device tree description of the DLINK DIR665 wireless access
point. The support for the 88E6171 switch will be added in a later
patch.

Signed-off-by: Claudio Leite <leitec@staticky.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1414793613-11798-2-git-send-email-andrew@lunn.ch


Signed-off-by: Jason Cooper <jason@lakedaemon.net>

This adds a device tree for the Nomadik NHK15 development kit
board.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

DT files to enable cygnus consisting on reference designs
and cygnus core configuration.

Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Arun Parameswaran <aparames@broadcom.com>
Tested-by: Jonathan Richardson <jonathar@broadcom.com>
Reviewed-by: JD (Jiandong) Zheng <jdzheng@broadcom.com>
Signed-off-by: Scott Branden <sbranden@broadcom.com>

Koelsch is no longer supported in legacy builds.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Forgotten by commit ad8c3af8 ("ARM: shmobile: r7s72100: Remove
legacy board support").

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
[horms+renesas@verge.net.au:  update for addition of r8a7794-alt.dtb]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

As a first example, add device tree and bindings for the
RealView PB1176.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add dtb files to build targets and let kbuild handle them. Thus,
special dtbs rules can be removed. This eases Makefiles and the
implementation of the support of vendor dtb subdirectories.

Signed-off-by: Robert Richter <rrichter@cavium.com>

Move dtbs install rules to Makefile.dtbinst. This change is needed to
implement support for dts vendor subdirs. The change makes Makefiles
easier and smaller as no longer the dtbs_install rule needs to be
defined. Another advantage is that install goals are not encoded in
targets anymore (%.dtb_dtbinst_).

Signed-off-by: Robert Richter <rrichter@cavium.com>

Adds initial support for the HP Chromebook 11.

Cc: Vincent Palatin <vpalatin@chromium.org>
Cc: Doug Anderson <dianders@chromium.org>
Cc: Stephan van Schaik <stephan@synkhronix.com>
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

The A80 Optimus Board is was launched with the Allwinner A80 SoC.
It was jointly developed by Allwinner and Merrii.

This board has a UART port, a JTAG connector, USB host ports, a USB
3.0 OTG connector, an HDMI output, a micro SD slot, 8G NAND flash,
4G DRAM, a camera sensor interface, a WiFi/BT combo chip, a headphone
jack, IR receiver, and additional GPIO headers.

This patch adds only basic support.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Andreas Färber <afaerber@suse.de>