- Aug 03, 2021
-
-
Vinay Belgaumkar authored
This prints out relevant SLPC info from the SLPC shared structure. We will send a H2G message which forces SLPC to update the shared data structure with latest information before reading it. v2: Address review comments (Michal W) v3: Remove unnecessary tasks from slpc_info (Michal W) v4: Rename function to intel_guc_slpc_print_info() (Michal W) v5: checkpatch() Reviewed-by:
Michal Wajdeczko <michal.wajdeczko@intel.com> Signed-off-by:
Vinay Belgaumkar <vinay.belgaumkar@intel.com> Signed-off-by:
Sundaresan Sujaritha <sujaritha.sundaresan@intel.com> Signed-off-by:
John Harrison <John.C.Harrison@Intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210730202119.23810-10-vinay.belgaumkar@intel.com
-
Vinay Belgaumkar authored
Add helpers to read the min/max frequency being used by SLPC. This is done by send a H2G command which forces SLPC to update the shared data struct which can then be read. These helpers will be used in a sysfs patch later on. v2: Address review comments (Michal W) v3: Return err in case of query failure (Michal W) v4: Move decode_min/max_freq to this patch Reviewed-by:
-
Vinay Belgaumkar authored
Add param set h2g helpers to set the min and max frequencies for use by SLPC. v2: Address review comments (Michal W) v3: Check for positive error code (Michal W) v4: Print generic error in set_param (Michal W) Reviewed-by:
-
Vinay Belgaumkar authored
The assumption when it was added was that GT would not be holding any gt_pm references. However, uc_init is called from gt_init_hw, which holds a forcewake ref. If SLPC enable fails, we will still be holding this ref, which will result in the BUG_ON. Reviewed-by:
Matthew Brost <matthew.brost@intel.com> Signed-off-by:
-
Vinay Belgaumkar authored
Add methods for interacting with GuC for enabling SLPC. Enable SLPC after GuC submission has been established. GuC load will fail if SLPC cannot be successfully initialized. Add various helper methods to set/unset the parameters for SLPC. They can be set using H2G calls or directly setting bits in the shared data structure. v2: Address several review comments, add new helpers for decoding the SLPC min/max frequencies. Use masks instead of hardcoded constants. (Michal W) v3: Split global_state_to_string function, and check for positive non-zero return value from intel_guc_send() (Michal W) v4: Optimize the stringify function and other comments (Michal W) v5: Enable slpc as well before declaring GuC submission status (Michal W) v6: Checkpatch() Reviewed-by:
-
Vinay Belgaumkar authored
Allocate data structures for SLPC and functions for initializing on host side. v2: Address review comments (Michal W) v3: Remove unnecessary header includes (Michal W) v4: Rebase v5: Move allocation of shared data into slpc_init() (Michal W) Reviewed-by:
-
Vinay Belgaumkar authored
Add constants and params that are needed to configure SLPC. v2: Add a new abi header for SLPC. Replace bitfields with genmasks. Address other comments from Michal W. v3: Add slpc H2G format in abi, other review commments (Michal W) v4: Update status bits according to latest spec v5: checkpatch() Reviewed-by:
-
Vinay Belgaumkar authored
Also ensure uc_init is called before we initialize RPS so that we can check for SLPC support. We do not need to enable up/down interrupts when SLPC is enabled. However, we still need the ARAT interrupt, which will be enabled separately later. v2: Explicitly return from intel_rps_enable with slpc check (Matthew B) Reviewed-by:
-
Vinay Belgaumkar authored
Add macros to check for SLPC support. This feature is currently supported for Gen12+ and enabled whenever GuC submission is enabled/selected. Include templates for SLPC init/fini and enable. v2: Move SLPC helper functions to intel_guc_slpc.c/.h. Define basic template for SLPC structure in intel_guc_slpc_types.h. Fix copyright (Michal W) v3: Review comments (Michal W) v4: Include supported/selected inside slpc struct (Michal W) Reviewed-by:
Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Signed-off-by:
-
- Jul 31, 2021
-
-
Lucas De Marchi authored
There's a missing sentinel since we are not using ARRAY_SIZE(), but rather checking that the .start is 0 to stop the iteration in mcr_range(). BUG: KASAN: global-out-of-bounds in mcr_range.isra.0+0x69/0xa0 [i915] Read of size 4 at addr ffffffffa0889928 by task modprobe/3881 Fixes: d8905ba7 ("drm/i915/xehp: Define multicast register ranges") Signed-off-by:
Lucas De Marchi <lucas.demarchi@intel.com> Reviewed-by:
Matt Roper <matthew.d.roper@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210730191115.2514581-1-lucas.demarchi@intel.com
-
- Jul 30, 2021
-
-
Matthew Auld authored
No need to hand roll the set_placements stuff, now that we have a helper for this. v2: add back the -ENODEV checking since it's possible for stolen to be probed, and yet still be non-functional Signed-off-by:
Matthew Auld <matthew.auld@intel.com> Cc: Jason Ekstrand <jason@jlekstrand.net> Reviewed-by:
Jason Ekstrand <jason@jlekstrand.net> Link: https://patchwork.freedesktop.org/patch/msgid/20210729094731.1953091-1-matthew.auld@intel.com
-
- Jul 29, 2021
-
-
Lucas De Marchi authored
Replace all remaining handling of GRAPHICS_VER {==,>=} 10 with {==,>=} 11. With the removal of CNL, there is no platform with graphics version equals 10. Signed-off-by:Rodrigo Vivi <rodrigo.vivi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210728220326.1578242-5-lucas.demarchi@intel.com
-
Lucas De Marchi authored
With the removal of CNL, let's consider ICL as the first platform using that index. Signed-off-by:
-
Lucas De Marchi authored
CNL is the only platform with GRAPHICS_VER == 10. With its removal we don't need to handle that version anymore. Also we can now reduce the max number of slices: the call to intel_sseu_set_info() with the highest number of slices comes from SKL and BDW with 3 slices. Recent platforms actually increase the number of subslices so the number of slices remain 1. Signed-off-by:
-
Lucas De Marchi authored
Only one reference to CNL that is not needed, but code is the same for GEN9_BC, so leave the code around and just remove the special case for CNL. Signed-off-by:
-
- Jul 28, 2021
-
-
Daniel Vetter authored
The module init code is somewhat misplaced in i915_pci.c, since it needs to pull in init/exit functions from every part of the driver and pollutes the include list a lot. Extract an i915_module.c file which pulls all the bits together, and allows us to massively trim the include list of i915_pci.c. The downside is that have to drop the error path check Jason added to catch when we set up the pci driver too early. I think that risk is acceptable for this pretty nice include. Reviewed-by:
Daniel Vetter <daniel.vetter@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210727121037.2041102-11-daniel.vetter@ffwll.ch
-
Daniel Vetter authored
No longer used. Reviewed-by:
-
Daniel Vetter authored
With the global kmem_cache shrink infrastructure gone there's nothing special and we can convert them over. I'm doing this split up into each patch because there's quite a bit of noise with removing the static global.slab_vmas to just a slab_vmas. We have to keep i915_drv.h include in i915_globals otherwise there's nothing anymore that pulls in GEM_BUG_ON. v2: Make slab static (Jason, 0day) Reviewed-by:
-
Daniel Vetter authored
With the global kmem_cache shrink infrastructure gone there's nothing special and we can convert them over. I'm doing this split up into each patch because there's quite a bit of noise with removing the static global.slab_dependencies|priorities to just a slab_dependencies|priorities. v2: Make slab static (Jason, 0day) Reviewed-by:
-
Daniel Vetter authored
With the global kmem_cache shrink infrastructure gone there's nothing special and we can convert them over. I'm doing this split up into each patch because there's quite a bit of noise with removing the static global.slab_requests|execute_cbs to just a slab_requests|execute_cbs. v2: Make slab static (Jason, 0day) Reviewed-by:
-
Daniel Vetter authored
With the global kmem_cache shrink infrastructure gone there's nothing special and we can convert them over. I'm doing this split up into each patch because there's quite a bit of noise with removing the static global.slab_objects to just a slab_objects. v2: Make slab static (Jason, 0day) Reviewed-by:
-
Daniel Vetter authored
With the global kmem_cache shrink infrastructure gone there's nothing special and we can convert them over. I'm doing this split up into each patch because there's quite a bit of noise with removing the static global.slab_luts to just a slab_luts. v2: Make slab static (Jason, 0day) Reviewed-by:
-
Daniel Vetter authored
With the global kmem_cache shrink infrastructure gone there's nothing special and we can convert them over. I'm doing this split up into each patch because there's quite a bit of noise with removing the static global.slab_ce to just a slab_ce. v2: Make slab static (Jason, 0day) Reviewed-by:
-
Daniel Vetter authored
With the global kmem_cache shrink infrastructure gone there's nothing special and we can convert them over. I'm doing this split up into each patch because there's quite a bit of noise with removing the static global.slab_blocks to just a slab_blocks. v2: Make slab static (Jason, 0day) Reviewed-by:
-
Daniel Vetter authored
With the global kmem_cache shrink infrastructure gone there's nothing special and we can convert them over. I'm doing this split up into each patch because there's quite a bit of noise with removing the static global.slab_cache to just a slab_cache. v2: Make slab static (Jason, 0day) Reviewed-by:
-
Daniel Vetter authored
When modesetting (aka the full pci driver, which has nothing to do with disable_display option, which just gives you the full pci driver without the display driver) is disabled, we load nothing and do nothing. So move that check first, for a bit of orderliness. With Jason's module init/exit table this now becomes trivial. Reviewed-by:
-
Matt Roper authored
During a rebase the parameters were partially renamed, but not completely. Since the subsequent patches that start using this macro haven't landed on an upstream tree yet this didn't cause a build failure. Fixes: 086df54e ("drm/i915/xehpsdv: add initial XeHP SDV definitions") Signed-off-by:
Caz Yokoyama <caz.yokoyama@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210723174239.1551352-2-matthew.d.roper@intel.com
-
Daniele Ceraolo Spurio authored
Unblock GuC submission on Gen11+ platforms. v2: (Martin Peres / John H) - Delete debug message when GuC is disabled by default on certain platforms Signed-off-by: -
Matthew Brost authored
Implement a simple static mapping algorithm of the i915 priority levels (int, -1k to 1k exposed to user) to the 4 GuC levels. Mapping is as follows: i915 level < 0 -> GuC low level (3) i915 level == 0 -> GuC normal level (2) i915 level < INT_MAX -> GuC high level (1) i915 level == INT_MAX -> GuC highest level (0) We believe this mapping should cover the UMD use cases (3 distinct user levels + 1 kernel level). In addition to static mapping, a simple counter system is attached to each context tracking the number of requests inflight on the context at each level. This is needed as the GuC levels are per context while in the i915 levels are per request. v2: (Daniele) - Add BUILD_BUG_ON to enforce ordering of priority levels - Add missing lockdep to guc_prio_fini - Check for return before setting context registered flag - Map DISPLAY priority or higher to highest guc prio - Update comment for guc_prio Signed-off-by:
-
John Harrison authored
Some testing environments and some heavier tests are slower than previous limits allowed for. For example, it can take multiple seconds for the 'context has been reset' notification handler to reach the 'kill the requests' code in the 'active' version of the 'reset engines' test. During which time the selftest gets bored, gives up waiting and fails the test. There is also an async thread that the selftest uses to pump work through the hardware in parallel to the context that is marked for reset. That also could get bored waiting for completions and kill the test off. Lastly, the flush at the of various test sections can also see timeouts due to the large amount of work backed up. This is also true of the live_hwsp_read test. Signed-off-by:
-
John Harrison authored
When GuC submission is enabled, the GuC controls engine resets. Rather than explicitly triggering a reset, the driver must submit a hanging context to GuC and wait for the reset to occur. Conversely, one of the tests specifically sends hanging batches to the engines but wants them to sit around until a manual reset of the full GT (including GuC itself). That means disabling GuC based engine resets to prevent those from killing the hanging batch too soon. So, add support to the scheduling policy helper for disabling resets as well as making them quicker! In GuC submission mode, the 'is engine idle' test basically turns into 'is engine PM wakelock held'. Independently, there is a heartbeat disable helper function that the tests use. For unexplained reasons, this acquires the engine wakelock before disabling the heartbeat and only releases it when re-enabling the heartbeat. As one of the tests tries to do a wait for idle in the middle of a heartbeat disabled section, it is therefore guaranteed to always fail. Added a 'no_pm' variant of the heartbeat helper that allows the engine to be asleep while also having heartbeats disabled. Signed-off-by:
-
Matthew Brost authored
Requests may take slightly longer with GuC submission, let's increase the timeouts in live_requests. Signed-off-by:
-
Rahul Kumar Singh authored
When GuC submission is enabled, the GuC controls engine resets. Rather than explicitly triggering a reset, the driver must submit a hanging context to GuC and wait for the reset to occur. Signed-off-by:
Rahul Kumar Singh <rahul.kumar.singh@intel.com> Signed-off-by:
-
Rahul Kumar Singh authored
When GuC submission is enabled, the GuC controls engine resets. Rather than explicitly triggering a reset, the driver must submit a hanging context to GuC and wait for the reset to occur. Signed-off-by:
-
John Harrison authored
There are many ways in which the hangcheck selftest can fail. Very few of them actually printed an error message to say what happened. So, fill in the missing messages. Signed-off-by:
-
Matthew Brost authored
This adds GuC backend support for i915_request_cancel(), which in turn makes CONFIG_DRM_I915_REQUEST_TIMEOUT work. This implementation makes use of fence while there are likely simplier options. A fence was chosen because of another feature coming soon which requires a user to block on a context until scheduling is disabled. In that case we return the fence to the user and the user can wait on that fence. v2: (Daniele) - A comment about locking the blocked incr / decr - A comments about the use of the fence - Update commit message explaining why fence - Delete redundant check blocked count in unblock function - Ring buffer implementation - Comment about blocked in submission path - Shorter rpm path v3: (Checkpatch) - Fix typos in commit message (Daniel) - Rework to simplier locking structure in guc_context_block / unblock Signed-off-by:
-
Matthew Brost authored
When using GuC submission, if a context gets banned disable scheduling and mark all inflight requests as complete. Cc: John Harrison <John.C.Harrison@Intel.com> Signed-off-by:
-
John Harrison authored
The media watchdog mechanism involves GuC doing a silent reset and continue of the hung context. This requires the i915 driver provide a golden context to GuC in the ADS. v2: (Matthew Brost): - Fix memory corruption in shmem_read (John H) - Use locals rather than defines for LR_* + SKIP_SIZE Signed-off-by:
-
John Harrison authored
Added the scheduling policy parameters to the 'guc_info' debugfs state dump. Signed-off-by:
-
John Harrison authored
Changing the reset module parameter has no effect on a running GuC. The corresponding entry in the ADS must be updated and then the GuC informed via a Host2GuC message. The new debugfs interface to module parameters allows this to happen. However, connecting the parameter data address back to anything useful is messy. One option would be to pass a new private data structure address through instead of just the parameter pointer. However, that means having a new (and different) data structure for each parameter and a new (and different) write function for each parameter. This method keeps everything generic by instead using a string lookup on the directory entry name. Signed-off-by:
-
