- Mar 30, 2021
-
-
Mikko Perttunen authored
Make syncpoint expiration checks always use the same logic used by the hardware. This ensures that there are no race conditions that could occur because of the hardware triggering a syncpoint interrupt and then the driver disagreeing. One situation where this could occur is if a job incremented a syncpoint too many times -- then the hardware would trigger an interrupt, but the driver would assume that a syncpoint value greater than the syncpoint's max value is in the future, and not clean up the job. Signed-off-by:
Mikko Perttunen <mperttunen@nvidia.com> Signed-off-by:
Thierry Reding <treding@nvidia.com>
-
Mikko Perttunen authored
Before this patch, cancelled waiters would only be cleaned up once their threshold value was reached. Make host1x_intr_put_ref process the cancellation immediately to fix this. Signed-off-by:
-
Mikko Perttunen authored
Show the number of pending waiters in the debugfs status file. This is useful for testing to verify that waiters do not leak or accumulate incorrectly. Signed-off-by:
-
Mikko Perttunen authored
Syncpoints don't need to be associated with any client, so remove the property, and expose host1x_syncpt_alloc. This will allow allocating syncpoints without prior knowledge of the engine that it will be used with. Signed-off-by:
-
Thierry Reding authored
The SOR resets are exclusively shared with the SOR power domain. This means that exclusive access can only be granted temporarily and in order for that to work, a rigorous sequence must be observed. To ensure that a single consumer gets exclusive access to a reset, each consumer must implement a rigorous protocol using the reset_control_acquire() and reset_control_release() functions. However, these functions alone don't provide any guarantees at the system level. Drivers need to ensure that the only a single consumer has access to the reset at the same time. In order for the SOR to be able to exclusively access its reset, it must therefore ensure that the SOR power domain is not powered off by holding on to a runtime PM reference to that power domain across the reset assert/deassert operation. This used to work fine by accident, but was revealed when recently more devices started to rely on the SOR power domain. Fixes: 11c632e1 ("drm/tegra: sor: Implement acquire/release for reset") Reported-by:
Jonathan Hunter <jonathanh@nvidia.com> Signed-off-by:
-
Thierry Reding authored
Coupling of display controllers used to rely on runtime PM to take the companion controller out of reset. Commit fd67e9c6 ("drm/tegra: Do not implement runtime PM") accidentally broke this when runtime PM was removed. Restore this functionality by reusing the hierarchical host1x client suspend/resume infrastructure that's similar to runtime PM and which perfectly fits this use-case. Fixes: fd67e9c6 ("drm/tegra: Do not implement runtime PM") Reported-by:
Dmitry Osipenko <digetx@gmail.com> Reported-by:
Paul Fertser <fercerpav@gmail.com> Tested-by:
-
Mikko Perttunen authored
To avoid false lockdep warnings, give each client lock a different lock class, passed from the initialization site by macro. Signed-off-by:
-
Dmitry Osipenko authored
RGB output doesn't allow to change parent clock rate of the display and PCLK rate is set to 0Hz in this case. The tegra_dc_commit_state() shall not set the display clock to 0Hz since this change propagates to the parent clock. The DISP clock is defined as a NODIV clock by the tegra-clk driver and all NODIV clocks use the CLK_SET_RATE_PARENT flag. This bug stayed unnoticed because by default PLLP is used as the parent clock for the display controller and PLLP silently skips the erroneous 0Hz rate changes because it always has active child clocks that don't permit rate changes. The PLLP isn't acceptable for some devices that we want to upstream (like Samsung Galaxy Tab and ASUS TF700T) due to a display panel clock rate requirements that can't be fulfilled by using PLLP and then the bug pops up in this case since parent clock is set to 0Hz, killing the display output. Don't touch DC clock if pclk=0 in order to fix the problem. Signed-off-by:
-
- Mar 13, 2021
-
-
Minchan Kim authored
commit 0d835962 ("zram: support page writeback") introduced two problems. It overwrites writeback_store's return value as kstrtol's return value, which makes return value zero so user could see zero as return value of write syscall even though it wrote data successfully. It also breaks index value in the loop in that it doesn't increase the index any longer. It means it can write only first starting block index so user couldn't write all idle pages in the zram so lose memory saving chance. This patch fixes those issues. Link: https://lkml.kernel.org/r/20210312173949.2197662-2-minchan@kernel.org Fixes: 0d835962("zram: support page writeback") Signed-off-by:
Minchan Kim <minchan@kernel.org> Reported-by:
Amos Bianchi <amosbianchi@google.com> Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: John Dias <joaodias@google.com> Cc: <stable@vger.kernel.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Minchan Kim authored
writeback_store's return value is overwritten by submit_bio_wait's return value. Thus, writeback_store will return zero since there was no IO error. In the end, write syscall from userspace will see the zero as return value, which could make the process stall to keep trying the write until it will succeed. Link: https://lkml.kernel.org/r/20210312173949.2197662-1-minchan@kernel.org Fixes: 3b82a051("drivers/block/zram/zram_drv.c: fix error return codes not being returned in writeback_store") Signed-off-by:
-
Peter Xu authored
After is_cow_mapping() is exported in mm.h, replace some manual checks elsewhere throughout the tree but start to use the new helper. Link: https://lkml.kernel.org/r/20210217233547.93892-5-peterx@redhat.com Signed-off-by:
Peter Xu <peterx@redhat.com> Reviewed-by:
Jason Gunthorpe <jgg@ziepe.ca> Cc: VMware Graphics <linux-graphics-maintainer@vmware.com> Cc: Roland Scheidegger <sroland@vmware.com> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Cc: David Gibson <david@gibson.dropbear.id.au> Cc: Gal Pressman <galpress@amazon.com> Cc: Jan Kara <jack@suse.cz> Cc: Jann Horn <jannh@google.com> Cc: Kirill Shutemov <kirill@shutemov.name> Cc: Kirill Tkhai <ktkhai@virtuozzo.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Wei Zhang <wzam@amazon.com> Signed-off-by:
-
- Mar 12, 2021
-
-
Christoph Hellwig authored
ns can be NULL at this point, and my move of the check from the original patch by Chaitanya broke this. Fixes: 0ec84df4 ("nvme-core: check ctrl css before setting up zns") Signed-off-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
Jens Axboe <axboe@kernel.dk>
-
Wei Yongjun authored
Fix to return negative error code -ENOMEM from the error handling case instead of 0, as done elsewhere in this function. Fixes: 53c218da ("driver/perf: Add PMU driver for the ARM DMC-620 memory controller") Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
Wei Yongjun <weiyongjun1@huawei.com> Link: https://lore.kernel.org/r/20210312080421.277562-1-weiyongjun1@huawei.com Signed-off-by:
Will Deacon <will@kernel.org>
-
Beata Michalska authored
We are required to call dev_pm_opp_put() from outside of the opp_table->lock as debugfs removal needs to happen lock-less to avoid circular dependency issues. commit cf1fac94 ("opp: Reduce the size of critical section in _opp_kref_release()") tried to fix that introducing a new routine _opp_get_next() which keeps returning OPPs that can be freed by the callers and this routine shall be called without holding the opp_table->lock. Though the commit overlooked the fact that the OPPs can be referenced by other users as well and this routine will end up dropping references which were taken by other users and hence freeing the OPPs prematurely. In effect, other users of the OPPs will end up having invalid pointers at hand. We didn't see any crash reports earlier as the exact situation never happened, though it is certainly possible. We need a way to mark which OPPs are no longer referenced by the OPP core, so we don't drop extra references to them accidentally. This commit adds another OPP flag, "removed", which is used to track this. And now we should never end up dropping extra references to the OPPs. Cc: v5.11+ <stable@vger.kernel.org> # v5.11+ Fixes: cf1fac94 ("opp: Reduce the size of critical section in _opp_kref_release()") Signed-off-by:
Beata Michalska <beata.michalska@arm.com> [ Viresh: Almost rewrote entire patch, added new "removed" field, rewrote commit log and added the correct Fixes tag. ] Co-developed-by:
Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by:
-
Dave Airlie authored
The index variable should only be increased in one place. Noticed this while trying to track down another oops. v2: use while loop. Fixes: f295c8cf ("drm/nouveau: fix dma syncing warning with debugging on.") Signed-off-by:
Dave Airlie <airlied@redhat.com> Reviewed-by:
Michael J. Ruhl <michael.j.ruhl@intel.com> Signed-off-by:
-
Tvrtko Ursulin authored
Commit 311a50e7 ("drm/i915: Add support for mandatory cmdparsing") introduced mandatory command parsing but setup failures were not translated into wedging the GPU which was probably the intent. Possible errors come in two categories. Either the sanity check on internal tables has failed, which should be caught in CI unless an affected platform would be missed in testing; or memory allocation failure happened during driver load, which should be extremely unlikely but for correctness should still be handled. v2: * Tidy coding style. (Chris) [airlied: cherry-picked to avoid rc1 base] Signed-off-by:
Tvrtko Ursulin <tvrtko.ursulin@intel.com> Fixes: 311a50e7 ("drm/i915: Add support for mandatory cmdparsing") Cc: Jon Bloomfield <jon.bloomfield@intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Chris Wilson <chris.p.wilson@intel.com> Reviewed-by:
Chris Wilson <chris.p.wilson@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210302114213.1102223-1-tvrtko.ursulin@linux.intel.com (cherry picked from commit 5a1a659762d35a6dc51047c9127c011303c77b7f) Signed-off-by:
Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by:
-
- Mar 11, 2021
-
-
Christoph Hellwig authored
Ever since the addition of multipage bio_vecs BIO_MAX_PAGES has been horribly confusingly misnamed. Rename it to BIO_MAX_VECS to stop confusing users of the bio API. Signed-off-by:
Matthew Wilcox (Oracle) <willy@infradead.org> Reviewed-by:
Martin K. Petersen <martin.petersen@oracle.com> Link: https://lore.kernel.org/r/20210311110137.1132391-2-hch@lst.de Signed-off-by:
-
Axel Lin authored
The valid selector is 0 ~ 0xbf, so the .n_voltages should be 0xc0. Signed-off-by:
Axel Lin <axel.lin@ingics.com> Link: https://lore.kernel.org/r/20210311020558.579597-1-axel.lin@ingics.com Signed-off-by:
Mark Brown <broonie@kernel.org>
-
Mathias Nyman authored
If port terminations are detected in suspend, but link never reaches U0 then xHCI may have an internal uncleared wake state that will cause an immediate wake after suspend. This wake state is normally cleared when driver clears the PORT_CSC bit, which is set after a device is enabled and in U0. Write 1 to clear PORT_CSC for ports that don't have anything connected when suspending. This makes sure any pending internal wake states in xHCI are cleared. Cc: stable@vger.kernel.org Tested-by:
Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20210311115353.2137560-5-mathias.nyman@linux.intel.com Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Forest Crossman authored
I've confirmed that both the ASMedia ASM1042A and ASM3242 have the same problem as the ASM1142 and ASM2142/ASM3142, where they lose some of the upper bits of 64-bit DMA addresses. As with the other chips, this can cause problems on systems where the upper bits matter, and adding the XHCI_NO_64BIT_SUPPORT quirk completely fixes the issue. Cc: stable@vger.kernel.org Signed-off-by:
Forest Crossman <cyrozap@gmail.com> Signed-off-by:
-
Mathias Nyman authored
A xHC USB 3 port might miss the first wake signal from a USB 3 device if the port LFPS reveiver isn't enabled fast enough after xHC resume. xHC host will anyway be resumed by a PME# signal, but will go back to suspend if no port activity is seen. The device resends the U3 LFPS wake signal after a 100ms delay, but by then host is already suspended, starting all over from the beginning of this issue. USB 3 specs say U3 wake LFPS signal is sent for max 10ms, then device needs to delay 100ms before resending the wake. Don't suspend immediately if port activity isn't detected in resume. Instead add a retry. If there is no port activity then delay for 120ms, and re-check for port activity. Cc: <stable@vger.kernel.org> Signed-off-by:
-
Stanislaw Gruszka authored
On some systems rt2800usb and mt7601u devices are unable to operate since commit f8f80be5 ("xhci: Use soft retry to recover faster from transaction errors") Seems that some xHCI controllers can not perform Soft Retry correctly, affecting those devices. To avoid the problem add xhci->quirks flag that restore pre soft retry xhci behaviour for affected xHCI controllers. Currently those are AMD_PROMONTORYA_4 and AMD_PROMONTORYA_2, since it was confirmed by the users: on those xHCI hosts issue happen and is gone after disabling Soft Retry. [minor commit message rewording for checkpatch -Mathias] Fixes: f8f80be5 ("xhci: Use soft retry to recover faster from transaction errors") Cc: <stable@vger.kernel.org> # 4.20+ Reported-by:
Bernhard <bernhard.gebetsberger@gmx.at> Tested-by:
Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by:
-
Dmitry Monakhov authored
This adds a quirk for Samsung PM1725a drive which fixes timeouts and I/O errors due to the fact that the controller does not properly handle the Write Zeroes command, dmesg log: nvme nvme0: I/O 528 QID 10 timeout, aborting nvme nvme0: I/O 529 QID 10 timeout, aborting nvme nvme0: I/O 530 QID 10 timeout, aborting nvme nvme0: I/O 531 QID 10 timeout, aborting nvme nvme0: I/O 532 QID 10 timeout, aborting nvme nvme0: I/O 533 QID 10 timeout, aborting nvme nvme0: I/O 534 QID 10 timeout, aborting nvme nvme0: I/O 535 QID 10 timeout, aborting nvme nvme0: Abort status: 0x0 nvme nvme0: Abort status: 0x0 nvme nvme0: Abort status: 0x0 nvme nvme0: Abort status: 0x0 nvme nvme0: Abort status: 0x0 nvme nvme0: Abort status: 0x0 nvme nvme0: Abort status: 0x0 nvme nvme0: Abort status: 0x0 nvme nvme0: I/O 528 QID 10 timeout, reset controller nvme nvme0: controller is down; will reset: CSTS=0x3, PCI_STATUS=0x10 nvme nvme0: Device not ready; aborting reset, CSTS=0x3 nvme nvme0: Device not ready; aborting reset, CSTS=0x3 nvme nvme0: Removing after probe failure status: -19 nvme0n1: detected capacity change from 6251233968 to 0 blk_update_request: I/O error, dev nvme0n1, sector 32776 op 0x1:(WRITE) flags 0x3000 phys_seg 6 prio class 0 blk_update_request: I/O error, dev nvme0n1, sector 113319936 op 0x9:(WRITE_ZEROES) flags 0x800 phys_seg 0 prio class 0 Buffer I/O error on dev nvme0n1p2, logical block 1, lost async page write blk_update_request: I/O error, dev nvme0n1, sector 113319680 op 0x9:(WRITE_ZEROES) flags 0x0 phys_seg 0 prio class 0 Buffer I/O error on dev nvme0n1p2, logical block 2, lost async page write blk_update_request: I/O error, dev nvme0n1, sector 113319424 op 0x9:(WRITE_ZEROES) flags 0x0 phys_seg 0 prio class 0 Buffer I/O error on dev nvme0n1p2, logical block 3, lost async page write blk_update_request: I/O error, dev nvme0n1, sector 113319168 op 0x9:(WRITE_ZEROES) flags 0x0 phys_seg 0 prio class 0 Buffer I/O error on dev nvme0n1p2, logical block 4, lost async page write blk_update_request: I/O error, dev nvme0n1, sector 113318912 op 0x9:(WRITE_ZEROES) flags 0x0 phys_seg 0 prio class 0 Buffer I/O error on dev nvme0n1p2, logical block 5, lost async page write blk_update_request: I/O error, dev nvme0n1, sector 113318656 op 0x9:(WRITE_ZEROES) flags 0x0 phys_seg 0 prio class 0 Buffer I/O error on dev nvme0n1p2, logical block 6, lost async page write blk_update_request: I/O error, dev nvme0n1, sector 113318400 op 0x9:(WRITE_ZEROES) flags 0x0 phys_seg 0 prio class 0 blk_update_request: I/O error, dev nvme0n1, sector 113318144 op 0x9:(WRITE_ZEROES) flags 0x0 phys_seg 0 prio class 0 blk_update_request: I/O error, dev nvme0n1, sector 113317888 op 0x9:(WRITE_ZEROES) flags 0x0 phys_seg 0 prio class 0 Signed-off-by:
Dmitry Monakhov <dmtrmonakhov@yandex-team.ru> Signed-off-by:
-
Lv Yunlong authored
In nvmet_rdma_write_data_done, rsp is recoverd by wc->wr_cqe and freed by nvmet_rdma_release_rsp(). But after that, pr_info() used the freed chunk's member object and could leak the freed chunk address with wc->wr_cqe by computing the offset. Signed-off-by:
Lv Yunlong <lyl2019@mail.ustc.edu.cn> Signed-off-by:
-
Chaitanya Kulkarni authored
Ensure multiple Command Sets are supported before starting to setup a ZNS namespace. Signed-off-by:
Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com> [hch: move the check around a bit] Signed-off-by:
-
James Smart authored
Recent patch to prevent calling __nvme_fc_abort_outstanding_ios in interrupt context results in a possible race condition. A controller reset results in errored io completions, which schedules error work. The change of error work to a work element allows it to fire after the ctrl state transition to NVME_CTRL_CONNECTING, causing any outstanding io (used to initialize the controller) to fail and cause problems for connect_work. Add a state check to only schedule error work if not in the RESETTING state. Fixes: 19fce047 ("nvme-fc: avoid calling _nvme_fc_abort_outstanding_ios from interrupt context") Signed-off-by:
Nigel Kirkland <nkirkland2304@gmail.com> Signed-off-by:
James Smart <jsmart2021@gmail.com> Signed-off-by:
-
Hannes Reinecke authored
When a command has been aborted we should return NVME_SC_HOST_ABORTED_CMD to be consistent with the other transports. Signed-off-by:
Hannes Reinecke <hare@suse.de> Reviewed-by:
Sagi Grimberg <sagi@grimberg.me> Reviewed-by:
Daniel Wagner <dwagner@suse.de> Signed-off-by:
-
Hannes Reinecke authored
nvme_fc_terminate_exchange() is being called when exchanges are being deleted, and as such we should be setting the NVME_REQ_CANCELLED flag to have identical behaviour on all transports. Signed-off-by:
Keith Busch <kbusch@kernel.org> Reviewed-by:
-
Hannes Reinecke authored
NVME_REQ_CANCELLED is translated into -EINTR in nvme_submit_sync_cmd(), so we should be setting this flags during nvme_cancel_request() to ensure that the callers to nvme_submit_sync_cmd() will get the correct error code when the controller is reset. Signed-off-by:
Chao Leng <lengchao@huawei.com> Reviewed-by:
-
Hannes Reinecke authored
We only should remove namespaces when we get fatal error back from the device or when the namespace IDs have changed. So instead of painfully masking out error numbers which might indicate that the error should be ignored we could use an NVME status code to indicated when the namespace should be removed. That simplifies the final logic and makes it less error-prone. Signed-off-by:
-
Chaitanya Kulkarni authored
The chunk_sectors value affects max_zone_append_sectors. Signed-off-by:
Kanchan Joshi <joshi.k@samsung.com> Signed-off-by:
-
Dafna Hirschfeld authored
The histogram mode is set using 'rkisp1_params_set_bits'. Only the bits of the mode should be the value argument for that function. Otherwise bits outside the mode mask are turned on which is not what was intended. Fixes: bae1155c ("media: staging: rkisp1: add output device for parameters") Signed-off-by:
Dafna Hirschfeld <dafna.hirschfeld@collabora.com> Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by:
Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
-
Biju Das authored
RZ/G2L SoC has no UIF. This patch fixes null pointer access, when UIF module is not used. Fixes: 5e824f98("media: v4l: vsp1: Integrate DISCOM in display pipeline") Signed-off-by:
Biju Das <biju.das.jz@bp.renesas.com> Signed-off-by:
-
Biju Das authored
RZ/G2L SoC has only BRS. This patch fixes null pointer access,when only BRS is enabled. Fixes: cbb7fa49("media: v4l: vsp1: Rename BRU to BRx") Signed-off-by:
-
Maxim Mikityanskiy authored
usbtv doesn't support power management, so on system suspend the .disconnect callback of the driver is called. The teardown sequence includes a call to snd_card_free. Its implementation waits until the refcount of the sound card device drops to zero, however, if its file is open, snd_card_file_add takes a reference, which can't be dropped during the suspend, because the userspace processes are already frozen at this point. snd_card_free waits for completion forever, leading to a hang on suspend. This commit fixes this deadlock condition by replacing snd_card_free with snd_card_free_when_closed, that doesn't wait until all references are released, allowing suspend to progress. Fixes: 63ddf68d ("[media] usbtv: add audio support") Signed-off-by:
Maxim Mikityanskiy <maxtram95@gmail.com> Signed-off-by:
-
Hans Verkuil authored
The rc-cec keymap is unusual in that it can't be built as a module, instead it is registered directly in rc-main.c if CONFIG_MEDIA_CEC_RC is set. This is because it can be called from drm_dp_cec_set_edid() via cec_register_adapter() in an asynchronous context, and it is not allowed to use request_module() to load rc-cec.ko in that case. Trying to do so results in a 'WARN_ON_ONCE(wait && current_is_async())'. Since this keymap is only used if CONFIG_MEDIA_CEC_RC is set, we just compile this keymap into the rc-core module and never as a separate module. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Sean Young <sean@mess.org> Signed-off-by:
-
Daniel Vetter authored
Some of them have gaps, or fields we don't clear. Native ioctl code does full copies plus zero-extends on size mismatch, so nothing can leak. But compat is more hand-rolled so need to be careful. None of these matter for performance, so just memset. Also I didn't fix up the CONFIG_DRM_LEGACY or CONFIG_DRM_AGP ioctl, those are security holes anyway. Acked-by:
Maxime Ripard <mripard@kernel.org> Reported-by: syzbot+620cf21140fc7e772a5d@syzkaller.appspotmail.com # vblank ioctl Cc: syzbot+620cf21140fc7e772a5d@syzkaller.appspotmail.com Cc: stable@vger.kernel.org Signed-off-by:
Daniel Vetter <daniel.vetter@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210222100643.400935-1-daniel.vetter@ffwll.ch (cherry picked from commit e926c474) Signed-off-by:
Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
-
Noralf Trønnes authored
dma-buf importing was reworked in commit 7d2cd72a ("drm/shmem-helpers: Simplify dma-buf importing"). Before that commit drm_gem_shmem_prime_import_sg_table() did set ->pages_use_count=1 and drm_gem_shmem_vunmap_locked() could call drm_gem_shmem_put_pages() unconditionally. Now without the use count set, put pages is called also on dma-bufs. Fix this by only putting pages if it's not imported. Signed-off-by:
Noralf Trønnes <noralf@tronnes.org> Fixes: 7d2cd72a ("drm/shmem-helpers: Simplify dma-buf importing") Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Thomas Zimmermann <tzimmermann@suse.de> Acked-by:
Thomas Zimmermann <tzimmermann@suse.de> Tested-by:
-
Artem Lapkin authored
Problem: random stucks on reboot stage about 1/20 stuck/reboots // debug kernel log [ 4.496660] reboot: kernel restart prepare CMD:(null) [ 4.498114] meson_ee_pwrc c883c000.system-controller:power-controller: shutdown begin [ 4.503949] meson_ee_pwrc c883c000.system-controller:power-controller: shutdown domain 0:VPU... ...STUCK... Solution: add shutdown function to meson_drm driver // debug kernel log [ 5.231896] reboot: kernel restart prepare CMD:(null) [ 5.246135] [drm:meson_drv_shutdown] ... [ 5.259271] meson_ee_pwrc c883c000.system-controller:power-controller: shutdown begin [ 5.274688] meson_ee_pwrc c883c000.system-controller:power-controller: shutdown domain 0:VPU... [ 5.338331] reboot: Restarting system [ 5.358293] psci: PSCI_0_2_FN_SYSTEM_RESET reboot_mode:0 cmd:(null) bl31 reboot reason: 0xd bl31 reboot reason: 0x0 system cmd 1. ...REBOOT... Tested: on VIM1 VIM2 VIM3 VIM3L khadas sbcs - 1000+ successful reboots and Odroid boards, WeTek Play2 (GXBB) Fixes: bbbe775e ("drm: Add support for Amlogic Meson Graphic Controller") Signed-off-by:
Artem Lapkin <art@khadas.com> Tested-by:
Christian Hewitt <christianshewitt@gmail.com> Acked-by:
Neil Armstrong <narmstrong@baylibre.com> Acked-by:
Kevin Hilman <khilman@baylibre.com> Signed-off-by:
-
Neil Roberts authored
When mmapping the shmem, it would previously adjust the pgoff in the vm_area_struct to remove the fake offset that is added to be able to identify the buffer. This patch removes the adjustment and makes the fault handler use the vm_fault address to calculate the page offset instead. Although using this address is apparently discouraged, several DRM drivers seem to be doing it anyway. The problem with removing the pgoff is that it prevents drm_vma_node_unmap from working because that searches the mapping tree by address. That doesn't work because all of the mappings are at offset 0. drm_vma_node_unmap is being used by the shmem helpers when purging the buffer. This fixes a bug in Panfrost which is using drm_gem_shmem_purge. Without this the mapping for the purged buffer can still be accessed which might mean it would access random pages from other buffers v2: Don't check whether the unsigned page_offset is less than 0. Cc: stable@vger.kernel.org Fixes: 17acb9f3 ("drm/shmem: Add madvise state and purge helpers") Signed-off-by:
Neil Roberts <nroberts@igalia.com> Reviewed-by:
Steven Price <steven.price@arm.com> Signed-off-by:
-
