- Sep 12, 2014
-
-
Florian Westphal authored
Instead of preallocating Rx skbs, allocate them right before sending inbound packet up the stack. e1000-kvm, mtu1500, netperf TCP_STREAM: Size Size Size Time Throughput bytes bytes bytes secs. 10^6bits/sec old: 87380 16384 16384 60.00 4532.40 new: 87380 16384 16384 60.00 4599.05 Signed-off-by:
Florian Westphal <fw@strlen.de> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Florian Westphal authored
and remove *page, its only used for Rx. Signed-off-by:
-
Florian Westphal authored
e1000 uses the same metadata struct for Rx and Tx. But Tx and Rx have different requirements. For Rx, we only need to store a buffer and a DMA address. Follow-up patch will remove skb for Rx, bringing rx_buffer_info down to 16 bytes on x86_64. [ buffer_info is 48 bytes ] Signed-off-by:
-
Florian Westphal authored
Currently we unmap the DMA range, then copy to new skb. Change this so we can keep the mapping in case the data is copied. Signed-off-by:
-
Florian Westphal authored
Its the same in both handlers. Signed-off-by:
-
Florian Westphal authored
... and make it static. Signed-off-by:
-
Alexander Duyck authored
This change addresses several issues in the current ixgbe implementation of busy poll sockets. First was the fact that it was possible for frames to be delivered out of order if they were held in GRO. This is addressed by flushing the GRO buffers before releasing the q_vector back to the idle state. The other issue was the fact that we were having to take a spinlock on changing the state to and from idle. To resolve this I have replaced the state value with an atomic and use atomic_cmpxchg to change the value from idle, and a simple atomic set to restore it back to idle after we have acquired it. This allows us to only use a locked operation on acquiring the vector without a need for a locked operation to release it. Signed-off-by:
Alexander Duyck <alexander.h.duyck@intel.com> Tested-by:
Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by:
-
Alexander Duyck authored
This change removes the Rx buffer allocation at the end of ixgbe_clean_rx_irq. The reason for removing this is to avoid the extra latency introduced by the MMIO write. This can amount to somewhere around an extra 100ns of latency and one extra message worth of PCIe bus overhead. Signed-off-by:
-
Mark Rustad authored
Resolve missing-field-initializers warnings by using designated initialization. Signed-off-by:
Mark Rustad <mark.d.rustad@intel.com> Tested-by:
-
Mark Rustad authored
This patch resolves warnings produced by ixgbe in W=2 kernel builds. There are missing-field-initializers warnings and shadow warnings. None of these point to any deeper problem, so just resolve them so any new warnings get analyzed. Signed-off-by:
-
- Sep 10, 2014
-
-
Daniel Borkmann authored
Since BPF JIT depends on the availability of module_alloc() and module_free() helpers (HAVE_BPF_JIT and MODULES), we better build that code only in case we have BPF_JIT in our config enabled, just like with other JIT code. Fixes builds for arm/marzen_defconfig and sh/rsk7269_defconfig. ==================== kernel/built-in.o: In function `bpf_jit_binary_alloc': /home/cwang/linux/kernel/bpf/core.c:144: undefined reference to `module_alloc' kernel/built-in.o: In function `bpf_jit_binary_free': /home/cwang/linux/kernel/bpf/core.c:164: undefined reference to `module_free' make: *** [vmlinux] Error 1 ==================== Reported-by:
Fengguang Wu <fengguang.wu@intel.com> Fixes: 738cbe72 ("net: bpf: consolidate JIT binary allocator") Signed-off-by:
Daniel Borkmann <dborkman@redhat.com> Acked-by:
Alexei Starovoitov <ast@plumgrid.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Hariprasad Shenai says: ==================== cxgb4: Allow FW size upto 1MB, support for S25FL032P flash and misc. fixes This patch series adds support to allow FW size upto 1MB, support for S25FL032P flash. Fix t4_flash_erase_sectors to throw an error, when erase sector aren't in the flash and also warning message when adapters have flashes less than 2Mb. Adds device id of new adapter and removes device id of debug adapter. The patches series is created against 'net-next' tree. And includes patches on cxgb4 driver and cxgb4vf driver. We have included all the maintainers of respective drivers. Kindly review the change and let us know in case of any review comments. ==================== Signed-off-by: -
Hariprasad Shenai authored
Signed-off-by:
Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by:
-
Hariprasad Shenai authored
Based on original work by Casey Leedom <leedom@chelsio.com> Signed-off-by:
-
Hariprasad Shenai authored
cxgb4: Fix t4_flash_erase_sectors() to throw an error when requested to erase sectors which aren't in the FLASH Based on original work by Casey Leedom <leedom@chelsio.com> Signed-off-by:
-
Hariprasad Shenai authored
Add support for Spansion S25FL032P flash Based on original work by Dimitris Michailidis Signed-off-by:
-
Hariprasad Shenai authored
Based on original work by Casey Leedom <leedom@chelsio.com> Signed-off-by:
-
Erik Hugne authored
This fixes the following sparse warnings: sparse: symbol 'tipc_update_nametbl' was not declared. Should it be static? Also, the function is changed to return bool upon success, rather than a potentially freed pointer. Signed-off-by:
Erik Hugne <erik.hugne@ericsson.com> Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Romain Perier authored
Free resources before being disconnected from phy and calling core driver is wrong and should not happen. It avoids a delay of 4-5s caused by the timeout of phy_disconnect(). Signed-off-by:
Romain Perier <romain.perier@gmail.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf-nextDavid S. Miller authored
Pablo Neira Ayuso says: ==================== nf-next pull request The following patchset contains Netfilter/IPVS updates for your net-next tree. Regarding nf_tables, most updates focus on consolidating the NAT infrastructure and adding support for masquerading. More specifically, they are: 1) use __u8 instead of u_int8_t in arptables header, from Mike Frysinger. 2) Add support to match by skb->pkttype to the meta expression, from Ana Rey. 3) Add support to match by cpu to the meta expression, also from Ana Rey. 4) A smatch warning about IPSET_ATTR_MARKMASK validation, patch from Vytas Dauksa. 5) Fix netnet and netportnet hash types the range support for IPv4, from Sergey Popovich. 6) Fix missing-field-initializer warnings resolved, from Mark Rustad. 7) Dan Carperter reported possible integer overflows in ipset, from Jozsef Kadlecsick. 8) Filter out accounting objects in nfacct by type, so you can selectively reset quotas, from Alexey Perevalov. 9) Move specific NAT IPv4 functions to the core so x_tables and nf_tables can share the same NAT IPv4 engine. 10) Use the new NAT IPv4 functions from nft_chain_nat_ipv4. 11) Move specific NAT IPv6 functions to the core so x_tables and nf_tables can share the same NAT IPv4 engine. 12) Use the new NAT IPv6 functions from nft_chain_nat_ipv6. 13) Refactor code to add nft_delrule(), which can be reused in the enhancement of the NFT_MSG_DELTABLE to remove a table and its content, from Arturo Borrero. 14) Add a helper function to unregister chain hooks, from Arturo Borrero. 15) A cleanup to rename to nft_delrule_by_chain for consistency with the new nft_*() functions, also from Arturo. 16) Add support to match devgroup to the meta expression, from Ana Rey. 17) Reduce stack usage for IPVS socket option, from Julian Anastasov. 18) Remove unnecessary textsearch state initialization in xt_string, from Bojan Prtvar. 19) Add several helper functions to nf_tables, more work to prepare the enhancement of NFT_MSG_DELTABLE, again from Arturo Borrero. 20) Enhance NFT_MSG_DELTABLE to delete a table and its content, from Arturo Borrero. 21) Support NAT flags in the nat expression to indicate the flavour, eg. random fully, from Arturo. 22) Add missing audit code to ebtables when replacing tables, from Nicolas Dichtel. 23) Generalize the IPv4 masquerading code to allow its re-use from nf_tables, from Arturo. 24) Generalize the IPv6 masquerading code, also from Arturo. 25) Add the new masq expression to support IPv4/IPv6 masquerading from nf_tables, also from Arturo. ==================== Signed-off-by: -
Joe Perches authored
Use the more common pr_warn. Other miscellanea: o Coalesce formats o Realign arguments Signed-off-by:
Joe Perches <joe@perches.com> Signed-off-by:
-
Joe Perches authored
Use the more common pr_warn. Coalesce formats. Realign arguments. Signed-off-by:
-
Joe Perches authored
Use the more common pr_warn. Realign arguments. Signed-off-by:
-
Joe Perches authored
Use the more common pr_warn. Signed-off-by:
-
David S. Miller authored
Tom Herbert says: ==================== net: enable GRO for IPIP and SIT This patch sets populates the IPIP and SIT offload structures with gro_receive and gro_complete functions. This enables use of GRO for these. Also, fixed a problem in IPv6 where we were not properly initializing flush_id. Peformance results are below. Note that these tests were done on bnx2x which doesn't provide RX checksum offload of IPIP or SIT (i.e. does not give CHEKCSUM_COMPLETE). Also, we don't get 4-tuple hash for RSS only 2-tuple in this case so all the packets between two hosts are winding up on the same queue. Net result is the interrupting CPU is the bottleneck in GRO (checksumming every packet there). Testing: netperf TCP_STREAM between two hosts using bnx2x. * Before fix IPIP 1 connection 6.53% CPU utilization 6544.71 Mbps 20 connections 13.79% CPU utilization 9284.54 Mbps SIT 1 connection 6.68% CPU utilization 5653.36 Mbps 20 connections 18.88% CPU utilization 9154.61 Mbps * After fix IPIP 1 connection 5.73% CPU utilization 9279.53 Mbps 20 connections 7.14% CPU utilization 7279.35 Mbps SIT 1 connection 2.95% CPU utilization 9143.36 Mbps 20 connections 7.09% CPU utilization 6255.3 Mbps ==================== Signed-off-by: -
Tom Herbert authored
Add ipv6_gro_receive and ipv6_gro_complete to sit_offload to support GRO. Signed-off-by:
Tom Herbert <therbert@google.com> Signed-off-by:
-
Tom Herbert authored
Add inet_gro_receive and inet_gro_complete to ipip_offload to support GRO. Signed-off-by:
-
Tom Herbert authored
In TCP gro we check flush_id which is derived from the IP identifier. In IPv4 gro path the flush_id is set with the expectation that every matched packet increments IP identifier. In IPv6, the flush_id is never set and thus is uinitialized. What's worse is that in IPv6 over IPv4 encapsulation, the IP identifier is taken from the outer header which is currently not incremented on every packet for Linux stack, so GRO in this case never matches packets (identifier is not increasing). This patch clears flush_id for every time for a matched packet in IPv6 gro_receive. We need to do this each time to overwrite the setting that would be done in IPv4 gro_receive per the outer header in IPv6 over Ipv4 encapsulation. Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Joe Perches authored
Use the much more common pr_warn instead of pr_warning. Other miscellanea: o Typo fixes submiting/submitting o Coalesce formats o Realign arguments o Add missing terminating '\n' to formats Signed-off-by:
-
Florian Westphal authored
Signed-off-by:
-
Eric Dumazet authored
net/ipv4/udp_offload.c:339:5: warning: symbol 'udp4_gro_complete' was not declared. Should it be static? Signed-off-by:
-
Eric Dumazet authored
net/core/net_namespace.c:227:18: warning: incorrect type in argument 1 (different address spaces) net/core/net_namespace.c:227:18: expected void const *<noident> net/core/net_namespace.c:227:18: got struct net_generic [noderef] <asn:4>*gen We can use rcu_access_pointer() here as read-side access to the pointer was removed at least one grace period ago. Signed-off-by:
-
Eric Dumazet authored
net/ipv6/udp_offload.c:159:5: warning: symbol 'udp6_gro_complete' was not declared. Should it be static? Signed-off-by:
-
Eric Dumazet authored
Remove one sparse warning : net/ipv4/ip_sockglue.c:328:22: warning: incorrect type in assignment (different address spaces) net/ipv4/ip_sockglue.c:328:22: expected struct ip_ra_chain [noderef] <asn:4>*next net/ipv4/ip_sockglue.c:328:22: got struct ip_ra_chain *[assigned] ra And replace one rcu_assign_ptr() by RCU_INIT_POINTER() where applicable. Signed-off-by:
-
Daniel Borkmann authored
It's not used anywhere, so just remove these. Signed-off-by:
-
Andy Shevchenko authored
Instead of looping in the code let's use kernel extension to dump small buffers. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
-
hayeswang authored
Replace mdelay with usleep_range to avoid busy loop. Signed-off-by:
Hayes Wang <hayeswang@realtek.com> Signed-off-by:
-
Willem de Bruijn authored
Few packets have timestamping enabled. Exit sock_tx_timestamp quickly in this common case. Signed-off-by:
Willem de Bruijn <willemb@google.com> Signed-off-by:
-
Florian Westphal authored
not used anymore since ddecf0f4 (net_sched: sfq: add optional RED on top of SFQ). Signed-off-by:
-
Rick Jones authored
Convert the normal transmit completion path from dev_kfree_skb_any() to dev_consume_skb_any() to help keep dropped packet profiling meaningful. Signed-off-by:
Rick Jones <rick.jones2@hp.com> Signed-off-by:
-
