Correct all SATA ahci and phy controller register
addresses and interrupt lines to proper values.

Fixes: 344a2e51 ("arm64: dts: Add SATA DT nodes for Stingray SoC")

Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Andrew Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

The Khadas VIM2 board connects the dwc3 controller to an internal 4-port
USB hub which. Two of these ports are accessible directly soldered to
the board, while the other two are accessible through the 40-pin "GPIO"
header.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

The Nexbox A95X provides two USB ports. Enable the SoC's USB controller
on this board to make these USB ports usable.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

The LibreTech CC ("Le Potato") board provides four USB connectors.
These are provided by a hub which is connected to the SoC's USB
controller.
Enable the SoC's USB controller to make the USB ports usable. Also turn
on the HDMI_5V regulator when powering on the PHY because (even though
it's not shown in the schematics) HDMI_5V also supplies the USB VBUS.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

All S905D (GXL) and S912 (GXM) reference boards (namely these are
P230, P231, Q200 and Q201) provide USB connectors.
This enables the USB controller on these boards to make the USB ports
actually usable.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

All boards based on the P212 reference design (the P212 reference board
itself and the Khadas VIM) have USB connectors (in case of the Khadas
VIM the first port is exposed through the USB Type-C connector, the
second port is connected to a 4-port USB hub).
This enables the USB controller on these boards to make the USB ports
actually usable.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

The USB configuration on GXM is slightly different than on GXL. The dwc3
controller's internal hub has three USB2 ports (instead of 2 on GXL)
along with a dedicated USB2 PHY for this port. However, it seems that
there are no pins on GXM which would allow connecting the third port to
a physical USB port.
Passing the third PHY is required though, because without it none of the
other USB ports is working (this seems to be a limitation of how the
internal USB hub works, if one PHY is disabled then no USB port works).

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

This adds USB host support to the Meson GXL SoC. A dwc3 controller is
used for host-mode, while a dwc2 controller (not added in this patch
because I could not get it working) is used for device-mode only.

The dwc3 controller's internal roothub has two USB2 ports enabled but no
USB3 port. Each of the ports is supplied by a separate PHY. The USB pins
are connected to the SoC's USBHOST_A and USBOTG_B pins.
Due to the way the roothub works internally the USB PHYs are left
enabled. When the dwc3 controller is disabled the PHY is never powered on
so it does not draw any extra power. However, when the dwc3 host
controller is enabled then all PHYs also have to be enabled, otherwise
USB devices will not be detected (regardless of whether they are plugged
into an enabled port or not). This means that only the dwc3 controller
has to be enabled on boards with USB support (instead of requiring all
boards to enable the PHYs additionally with the chance of forgetting to
enable one and breaking all other ports with that as well).

This also adds the USB3 PHY which currently only does some basic
initialization. That however is required because without it high-speed
devices (like USB thumb drives) do not work on some devices (probably
because the bootloader does not configure the USB3 PHY registers).

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

/smb@8000000/motherboard/gpio_keys node doesn't have "ranges" or "reg"
property in child nodes. So it's unnecessary to have address-cells
as well as size-cells properties which results in below warning.

Warning (avoid_unnecessary_addr_size):
/smb@8000000/motherboard/gpio_keys:
	unnecessary #address-cells/#size-cells without "ranges" or child "reg"
	property

This patch drops the unnecessary address+size-cell properties.

Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

Add nodes of the AVE ethernet controller for PXs3 and the boards.
This SoC has two controllers.

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

The "cooling-min-level" and "cooling-max-level" properties are not
parsed by any part of the kernel currently and the max cooling state of
gpio-fan cooling device is found by referring to the
"gpio-fan,speed-map" instead.

Remove the unused properties from the gpio-fan node.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

The "cooling-min-level" and "cooling-max-level" properties are not
parsed by any part of the kernel currently and the max cooling state of
a CPU cooling device is found by referring to the cpufreq table instead.

Remove the unused properties from the CPU nodes.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

This reverts commit f81d7af7.

As explained by Rob Herring:

"This "fix" is wrong. Memory controllers with chip selects should have
the chip select in the unit-address. The correct fix here is you should
drop "simple-bus"."

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Disable the USB overcurrent condition that is falsely detected on the
devkit.

Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>

Enables the watchdog0 timer on the Stratix10 devkit.

Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>

This patch adds syscon property for specifying soc-glue core into
device-tree of LD11/LD20 SoC.

Currently, soc-glue core is used for changing the state of S/PDIF
signal output pin to signal output state or Hi-Z state.

Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

The Xunlong Orange Pi Zero Plus is single board computer.
- H5 Quad-core 64-bit Cortex-A53
- 512MB DDR3
- microSD slot
- Debug TTL UART
- 1000M/100M/10M Ethernet RJ45
- Realtek RTL8189FTV
- Spi flash (2MB)
- One USB 2.0 HOST, One USB 2.0 OTG

This is based on a patch from armbian:
https://github.com/armbian/build/blob/master/patch/kernel/sunxi-next/sunxi-add-orangepi-zero-plus.patch



Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

efuse is one time programmable, so it is safer to deny write request
to this memory, unless the user is savvy enough to remove the read-only
flag from DTB

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

The Mali-450 IP can run up to 744MHz, bump the frequency using
the GP0 PLL clock.

Cc: Michal Lazo <michal.lazo@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

The TERES-I is an open hardware laptop built by Olimex using the
Allwinner A64 SoC.

Add the board specific .dts file, which includes the A64 .dtsi and
enables the peripherals that we support so far.

Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

The A64 SoC features two display pipelines, one has a LCD output, the
other has a HDMI output.

Add support for simplefb for the LCD output. Tested on Teres I.

This patch was inspired by work of Icenowy Zheng.

Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

Add a watchdog node for the A64, automatically enabled on all boards.
Since the device is compatible with an existing driver, we only reserve
a new compatible string to be used together with the fall back.
Tested on Olimex Teres-I.

Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

Add the proper pin group node to reference in board files.

Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

Pine H64 is an Allwinner H6-based SBC from Pine64, with the following
features:

- 1GiB/2GiB/4GiB LPDDR3 DRAM (in 4GiB situation only 3GiB is
accessible)
- AXP805 PMIC
- Raspberry-Pi-compatible GPIO header, "Euler" GPIO header (not
compatible with the "Euler" on Pine A64) and "Expansion" pin header
- 2 USB 2.0 ports and 1 USB 3.0 ports
- Audio jack
- MicroSD slot and eMMC module slot
- on-board SPI NOR flash
- 1Gbps Ethernet port (via RTL8211E PHY)
- HDMI port

Adds initial support for it, including the UART on the Expansion pin
header.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

Allwinner H6 is a new SoC with Cortex-A53 cores from Allwinner, with its
memory map fully reworked and some high-speed peripherals (PCIe, USB
3.0) introduced.

This commit adds the basical DTSI file of it, including the clock
support and UART support.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

The schematic of the espressobin is publicly available, add a comment
where to find it.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

This extra clock is needed to access the registers of the PCIe host
controller used on CP110 component of the Armada 7K/8K SoCs.

This follow the changes already made in the binding documentation (as
well as in the driver): "PCI: armada8k: Fix clock resource by adding
a register clock"

Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

This extra clock is needed to access the registers of the NAND controller
used on CP110 component of the Armada 7K/8K SoCs.

This follow the changes already made in the binding documentation (as
well as in the driver): "mtd: nand: marvell: Fix clock resource by adding
a register clock"

Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

This extra clock is needed to access the registers of the safexcel EIP97
used on CP110 component of the Armada 7K/8K SoCs.

This follow the changes already made in the binding documentation (as
well as in the driver): "crypto: inside-secure - fix clock resource by
adding a register clock"

Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

This extra clock is needed to access the registers of the harware RNG
used on CP110 component of the Armada 7K/8K SoCs.

This follow the changes already made in the binding documentation (as
well as in the driver): "hwrng: omap - Fix clock resource by adding a
register clock"

Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

This extra clock is needed to access the registers of the XOR engine
controller used on CP110 component of the Armada 7K/8K SoCs.

This follow the changes already made in the binding documentation (as
well as in the driver): "dmaengine: mv_xor_v2: Fix clock resource by
adding a register clock"

Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

This extra clock is needed to access the registers of the USB host
controller used on Armada 7K/8K SoCs.

This follow the changes already made in the binding documentation (as
well as in the driver): "usb: host: xhci-plat: Fix clock resource by
adding a register clock"

Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

Add auxadc device node for MT2712.

Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>

According to Documentation/process/license-rules.rst, move the SPDX
License Identifier to the very top of the file.  I used C++ comment
style not only for the SPDX line but for the entire block because
this seems Linus' preference [1].  I also dropped the parentheses to
follow the examples in that document.

[1] https://lkml.org/lkml/2017/11/25/133



Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

This patch adds regulators that have fixed voltage for audio codec
on UniPhier LD11/20 Global boards. This patch fixes warnings about
TAS57xx audio codec such as "tas571x 0-001b: 0-001b supply AVDD
not found, using dummy regulator".

Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Add nodes of the AVE ethernet controller for LD11 and LD20 SoCs
and the boards.

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

This patch adds compress audio node for S/PDIF on UniPhier LD11/20
global boards. And adds settings of AIO for it.

Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

This patch adds codec node for TI TAS571x on UniPhier LD11/20
global boards. And adds settings of AIO for speaker out.

Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

This patch adds audio controller, codec and simple card node of
UniPhier AIO sound system for LD11/20 SoCs.

Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Since 'num-slots' had already deprecated, remove the property in
device-tree file.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>