This patch adds pinctrl file for mt2712.

Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>

add new clocks according to ECO design change

Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>

Add nodes of the AVE ethernet controller for PXs3 and the boards.
This SoC has two controllers.

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

The "cooling-min-level" and "cooling-max-level" properties are not
parsed by any part of the kernel currently and the max cooling state of
gpio-fan cooling device is found by referring to the
"gpio-fan,speed-map" instead.

Remove the unused properties from the gpio-fan node.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

The "cooling-min-level" and "cooling-max-level" properties are not
parsed by any part of the kernel currently and the max cooling state of
a CPU cooling device is found by referring to the cpufreq table instead.

Remove the unused properties from the CPU nodes.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

This reverts commit f81d7af7.

As explained by Rob Herring:

"This "fix" is wrong. Memory controllers with chip selects should have
the chip select in the unit-address. The correct fix here is you should
drop "simple-bus"."

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Disable the USB overcurrent condition that is falsely detected on the
devkit.

Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>

Enables the watchdog0 timer on the Stratix10 devkit.

Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>

This patch adds syscon property for specifying soc-glue core into
device-tree of LD11/LD20 SoC.

Currently, soc-glue core is used for changing the state of S/PDIF
signal output pin to signal output state or Hi-Z state.

Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

The Xunlong Orange Pi Zero Plus is single board computer.
- H5 Quad-core 64-bit Cortex-A53
- 512MB DDR3
- microSD slot
- Debug TTL UART
- 1000M/100M/10M Ethernet RJ45
- Realtek RTL8189FTV
- Spi flash (2MB)
- One USB 2.0 HOST, One USB 2.0 OTG

This is based on a patch from armbian:
https://github.com/armbian/build/blob/master/patch/kernel/sunxi-next/sunxi-add-orangepi-zero-plus.patch



Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

efuse is one time programmable, so it is safer to deny write request
to this memory, unless the user is savvy enough to remove the read-only
flag from DTB

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

The Mali-450 IP can run up to 744MHz, bump the frequency using
the GP0 PLL clock.

Cc: Michal Lazo <michal.lazo@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

The TERES-I is an open hardware laptop built by Olimex using the
Allwinner A64 SoC.

Add the board specific .dts file, which includes the A64 .dtsi and
enables the peripherals that we support so far.

Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

The A64 SoC features two display pipelines, one has a LCD output, the
other has a HDMI output.

Add support for simplefb for the LCD output. Tested on Teres I.

This patch was inspired by work of Icenowy Zheng.

Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

Add a watchdog node for the A64, automatically enabled on all boards.
Since the device is compatible with an existing driver, we only reserve
a new compatible string to be used together with the fall back.
Tested on Olimex Teres-I.

Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

Add the proper pin group node to reference in board files.

Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

Pine H64 is an Allwinner H6-based SBC from Pine64, with the following
features:

- 1GiB/2GiB/4GiB LPDDR3 DRAM (in 4GiB situation only 3GiB is
accessible)
- AXP805 PMIC
- Raspberry-Pi-compatible GPIO header, "Euler" GPIO header (not
compatible with the "Euler" on Pine A64) and "Expansion" pin header
- 2 USB 2.0 ports and 1 USB 3.0 ports
- Audio jack
- MicroSD slot and eMMC module slot
- on-board SPI NOR flash
- 1Gbps Ethernet port (via RTL8211E PHY)
- HDMI port

Adds initial support for it, including the UART on the Expansion pin
header.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

Allwinner H6 is a new SoC with Cortex-A53 cores from Allwinner, with its
memory map fully reworked and some high-speed peripherals (PCIe, USB
3.0) introduced.

This commit adds the basical DTSI file of it, including the clock
support and UART support.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

The schematic of the espressobin is publicly available, add a comment
where to find it.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

This extra clock is needed to access the registers of the PCIe host
controller used on CP110 component of the Armada 7K/8K SoCs.

This follow the changes already made in the binding documentation (as
well as in the driver): "PCI: armada8k: Fix clock resource by adding
a register clock"

Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

This extra clock is needed to access the registers of the NAND controller
used on CP110 component of the Armada 7K/8K SoCs.

This follow the changes already made in the binding documentation (as
well as in the driver): "mtd: nand: marvell: Fix clock resource by adding
a register clock"

Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

This extra clock is needed to access the registers of the safexcel EIP97
used on CP110 component of the Armada 7K/8K SoCs.

This follow the changes already made in the binding documentation (as
well as in the driver): "crypto: inside-secure - fix clock resource by
adding a register clock"

Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

This extra clock is needed to access the registers of the harware RNG
used on CP110 component of the Armada 7K/8K SoCs.

This follow the changes already made in the binding documentation (as
well as in the driver): "hwrng: omap - Fix clock resource by adding a
register clock"

Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

This extra clock is needed to access the registers of the XOR engine
controller used on CP110 component of the Armada 7K/8K SoCs.

This follow the changes already made in the binding documentation (as
well as in the driver): "dmaengine: mv_xor_v2: Fix clock resource by
adding a register clock"

Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

This extra clock is needed to access the registers of the USB host
controller used on Armada 7K/8K SoCs.

This follow the changes already made in the binding documentation (as
well as in the driver): "usb: host: xhci-plat: Fix clock resource by
adding a register clock"

Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

Add auxadc device node for MT2712.

Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>

According to Documentation/process/license-rules.rst, move the SPDX
License Identifier to the very top of the file.  I used C++ comment
style not only for the SPDX line but for the entire block because
this seems Linus' preference [1].  I also dropped the parentheses to
follow the examples in that document.

[1] https://lkml.org/lkml/2017/11/25/133



Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

This patch adds regulators that have fixed voltage for audio codec
on UniPhier LD11/20 Global boards. This patch fixes warnings about
TAS57xx audio codec such as "tas571x 0-001b: 0-001b supply AVDD
not found, using dummy regulator".

Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Add nodes of the AVE ethernet controller for LD11 and LD20 SoCs
and the boards.

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

This patch adds compress audio node for S/PDIF on UniPhier LD11/20
global boards. And adds settings of AIO for it.

Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

This patch adds codec node for TI TAS571x on UniPhier LD11/20
global boards. And adds settings of AIO for speaker out.

Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

This patch adds audio controller, codec and simple card node of
UniPhier AIO sound system for LD11/20 SoCs.

Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Since 'num-slots' had already deprecated, remove the property in
device-tree file.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Since 'num-slots' had already deprecated, remove the property in
device-tree file.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Enable AHCI on Jetson TX1 and add sata phy node.

Signed-off-by: Preetham Chandru R <pchandru@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Populate the SATA node for Tegra210.

Signed-off-by: Preetham Ramchandra <pchandru@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Add the (previously omitted) SCIF0 pin data to the V3M Starter Kit board's
device tree.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

On R-Car H3, on-chip peripheral modules that can make use of DMA are
wired to either SYS-DMAC0 only, or to both SYS-DMAC1 and SYS-DMAC2.

Add the missing DMA properties pointing to SYS-DMAC2 for HSCIF[0-2],
SCIF[0125], and I2C[0-2].  These were initially left out because early
firmware versions prohibited using SYS-DMAC2.  This restriction has been
lifted in IPL and Secure Monitor Rev1.0.6 (released on Feb 25, 2016).

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add r8a7795 IPMMU-PV1 and keep it disabled by default.

This device is not present in r8a7795 ES1.x and
is removed from the DT of those SoCs.

This corrects an omission in
3b7e7848 ("arm64: dts: renesas: r8a7795: Add IPMMU device nodes")

This does not have any runtime effect.

Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>

Sort root sub-nodes alphabetically for allow for easier maintenance of
this file.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>