CHECK: multiple assignments should be avoided

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add comments to memory barriers per strict checkpatch.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The POEMB register is 32 bits, not 16.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The MDIO controller on the Frame Manager (Fman) is compatible with the
QE and Gianfar MDIO controllers, but we don't care about the TBI because
the Ethernet drivers (FMD) take care of programming it.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Take advantage of the new mdiobus_alloc_size() function to combine three
different memory allocations into one.  This also simplies the error
handling.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make the device tree probe function more data-driven, so that it no longer
searches the 'compatible' property more than once.  The of_device_id[] array
allows for per-entry private data, so we use that to store details about each
type of node that the driver supports.  This removes the need to check the
'compatible' property inside the probe function.

The driver supports four types on MDIO devices:

1) Gianfar MDIO nodes that only map the MII registers
2) Gianfar MDIO nodes that map the full MDIO register set
3) eTSEC2 MDIO nodes (which map the full MDIO register set)
4) QE MDIO nodes (which map only the MII registers)

Gianfar, eTSEC2, and QE have different mappings for the TBIPA register, which
is needed to initialize the TBI PHY.  In addition, the QE needs a special
hack because of the way the device tree is ordered.

All of this information is encapsulated in the fsl_pq_mdio_data structure,
so when an MDIO node is probed, per-device data and functions are used
to determine how to initialize the device.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1) Replace printk with dev_err

2) Fix some whitespace mistakes

3) Rename "ofdev" to "pdev", since it's a platform_device now

4) Fix an inadvertent compound statement by replacing commas with semicolons

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A few small functions were called only by other functions in the same
file, so merge them together.  One function, for example, was calculating
the device address even though the caller was doing the same thing.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove several unnecessary #include statements.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

None of the functions in fsl_pq_mdio.c are used by any other source file,
so there's no point in exporting them.  Merge the header file into the
source file, make all the functions static, remove any EXPORT_SYMBOL
statements, and delete any #include "fsl_pq_mdio.h" statements.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Free was missing and kcalloc() is better placed in be_ctrl_init()

Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

BE3 FW initializes VF tx-rate to 100Mbps. Fix this to 10Gbps.

Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

BE3 FW allocates VF resources for upto 30 VFs per PF while a max value of 32
may be reported via PCI config space. Fix this in the driver.

Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Changes from commit df505e were incorrectly over-written by commit 10ef9ab4.
Fixing the same.

Change log of the original fix:
    Currently RSS rings are not created in a multi-channel config.
    RSS rings can be created on one (out of four) interfaces per port in a
    multi-channel config. Doing this insulates the driver from a FW bug wherin
    multi-channel config is wrongly reported even when not enabled. This also
    helps performance in a multi-channel config, as one interface per port gets
    RSS rings.

Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The IEEE 802.15.4 standard represents a networking protocol. I don't
exactly know why drivers for this protocol are stored into the root
'driver' folder, but better will be to store them with other
networking stuff. Currently there are only 3 drivers available for
IEEE 802.15.4 stack, so lets do it now with the smallest overhead.

Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The code under _init and _exit functions is similar to the code of
module_spi_driver macro, which is a wrapper to the module_driver macro,
so use it instead.

Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Cc: Devendra Naga <develkernel412222@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>

Delete successive assignments to the same location.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/

)

// <smpl>
@@
expression i;
@@

*i = ...;
 i = ...;
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

This complements patch "net-forcedeth: fix TX timeout caused by TX
pause on down link" which ensures that a lock-up sequence is not sent
to the NIC. Present patch ensures that if a NIC is already locked-up,
the driver will recover from it when initializing the device.

It does the equivalent of the following recovery sequence:
 - write NVREG_TX_PAUSEFRAME_ENABLE_V1 to eth1's register
   NvRegTxPauseFrame
 - write NVREG_XMITCTL_START to eth1's register
   NvRegTransmitterControl
 - write 0 to eth1's register NvRegTransmitterControl
(this is at the heart of the "unbricking" sequence mentioned in patch
 "net-forcedeth: fix TX timeout caused by TX pause on down link")

Tested:
 - hardware is MCP55 device id 10de:0373 (rev a3), dual-port
 - reboot a kernel without any of patches mentioned
 - freeze the NIC (details on description for commit "net-forcedeth:
   fix TX timeout caused by TX pause on down link")
 - wait 5mn until ping hangs & TX timeout in dmesg
 - reboot on kernel with present patch
 - host is immediatly operational, no TX timeout

Signed-off-by: David Decotigny <decot@googlers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On some dual-port forcedeth devices such as MCP55 10de:0373 (rev a3),
when autoneg & TX pause are enabled while port is connected but
interface is down, the NIC will eventually freeze (TX timeouts,
network unreachable).

This patch ensures that TX pause is not configured in hardware when
interface is down. The TX pause request will be honored when interface
is later configured.

Tested:
 - hardware is MCP55 device id 10de:0373 (rev a3), dual-port
 - eth0 connected and UP, eth1 connected but DOWN
 - without this patch, following sequence would brick NIC:
      ifconfig eth0 down
      ifconfig eth1 up
      ifconfig eth1 down
      ethtool -A eth1 autoneg off rx on tx off
      ifconfig eth1 up
      ifconfig eth1 down
      ethtool -A eth1 autoneg on rx on tx on
      ifconfig eth1 up
      ifconfig eth1 down
      ifup eth0
      sleep 120  # or longer
      ethtool eth1
   Just in case, sequence to un-brick:
      ifconfig eth0 down
      ethtool -A eth1 autoneg off rx on tx off
      ifconfig eth1 up
      ifconfig eth1 down
      ifup eth0
 - with this patch: no TX timeout after "bricking" sequence above

Details:
 - The following register accesses have been identified as the ones
   causing the NIC to freeze in "bricking" sequence above:
    - write NVREG_TX_PAUSEFRAME_ENABLE_V1 to eth1's register NvRegTxPauseFrame
    - write NVREG_MISC1_PAUSE_TX | NVREG_MISC1_FORCE to eth1's register NvRegMisc1
    - write 0 to eth1's register NvRegTransmitterControl
   This is what this patch avoids.

Signed-off-by: David Decotigny <decot@googlers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Found by manual code inspection.

Tested: compile, reboot, ethtool -d ethX

Signed-off-by: David Decotigny <decot@googlers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for an MDIO bus multiplexer controlled by a simple memory-mapped
device, like an FPGA.  The device must be memory-mapped and contain only
8-bit registers (which keeps things simple).

Tested on a Freescale P5020DS board which uses the "PIXIS" FPGA attached
to the localbus.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch cleans up the way device tree support is added in mdio-gpio
driver. I found lot of code duplication which is not necessary.
Also strangely a new platform driver was also introduced for device tree
support. All this forced me to do this cleanup patch.
After this patch, the driver probe checks the of_node pointer to get the
data from device tree.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds dummy functions in of_mdio.h, so that driver need not
ifdef there code with CONFIG_OF.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Let's fill IP header ident field with a meaningful value,
it might help some setups.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When moving a net device from one net namespace to another
net namespace,dev_change_net_namespace calls NETDEV_DOWN
event,so the original net namespace's dst entries which
beloned to this net device will be put into dst_garbage
list.

then dev_change_net_namespace will set this net device's
net to the new net namespace.

If we unregister this net device's driver, this will trigger
the NETDEV_UNREGISTER_FINAL event, dst_ifdown will be called,
and get this net device's dst entries from dst_garbage list,
put these entries' dev to the new net namespace's lo device.

It's not what we want,actually we need these dst entries hold
the original net namespace's lo device,this incorrect device
holding will trigger emg message like below.
unregister_netdevice: waiting for lo to become free. Usage count = 1

so we should call NETDEV_UNREGISTER_FINAL event in
dev_change_net_namespace too,in order to make sure dst entries
already in the dst_garbage list, we need rcu_barrier before we
call NETDEV_UNREGISTER_FINAL event.

With help form Eric Dumazet.

Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is an initial merge in of Eric Biederman's work to start adding
user namespace support to the networking.

Signed-off-by: David S. Miller <davem@davemloft.net>

Ben Hutchings says:

====================
1. Change the TX path to stop queues earlier and avoid returning
NETDEV_TX_BUSY.
2. Remove some inefficiencies in soft-TSO.
3. Fix various bugs involving device state transitions and/or reset
scheduling by error handlers.
4. Take advantage of my previous change to operstate initialisation.
5. Miscellaneous cleanup.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

John W. Linville says:

====================
This is a batch of updates intended for 3.7.  The bulk of it is
mac80211 changes, including some mesh work from Thomas Pederson and
some multi-channel work from Johannes.  A variety of driver updates
and other bits are scattered in there as well.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Following commit 8f4cccbb ('net: Set device operstate at registration
time') it is now correct and preferable to set the carrier off before
registering a device.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

We also stop clearing *efx in efx_init_struct().  This is safe because
alloc_etherdev_mq() already clears it for us.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

RX DMA is limited by the length specified in each descriptor and not
by the MAC.  Over-length frames may get into the RX FIFO regardless of
the MAC settings, due to a hardware bug, but they will be truncated by
the packet DMA engine and reported as such in the completion event.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

We try to defer resets while the device is not READY, but we're not
doing this quite correctly.  In particular, changes to efx_nic::state
are documented as serialised by the RTNL lock, but they aren't.

1. We check whether a reset was requested during probe (suggesting
broken hardware) before we allow requested resets to be scheduled.
This leaves a window where a requested reset would be deferred
indefinitely.

2. Although we cancel the reset work item during device removal,
there are still later operations that can cause it to be scheduled
again.  We need to check the state before scheduling it.

3. Since the state can change between scheduling and running of
the work item, we still need to check it there, and we need to
do so *after* acquiring the RTNL lock which serialises state
changes.

4. We must cancel the reset work item during device removal, if the
state could ever have been READY.  This wasn't done in some of the
failure paths from efx_pci_probe().  Move the cancellation to
efx_pci_remove_main().

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

The current informational message doesn't properly explain what
happens, and could also appear if we defer a reset during
suspend/resume.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

efx_change_mtu() and efx_realloc_channels() each stop and start much
of the NIC, even if it has been disabled.  Since efx_start_all() is a
no-op when the NIC is disabled, this is probably harmless in the case
of efx_change_mtu(), but efx_realloc_channels() also reenables
interrupts which could be a bad thing to do.

Change efx_start_all() and efx_start_interrupts() to assert that the
NIC is not disabled, but make efx_stop_interrupts() do nothing if the
NIC is disabled (since it is already stopped), consistent with
efx_stop_all().

Update comments for efx_start_all() and efx_stop_all() to describe
their purpose and preconditions more accurately.

Add a common function to check and log if the NIC is disabled, and use
it in efx_net_open(), efx_change_mtu() and efx_realloc_channels().

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

Interrupt state should be consistently guarded by the RTNL lock once
the net device is registered.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

Currently we ignore and clear the disabled state.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

I don't think these PM functions can race with userland net device
operations, but it's much easier to reason about locking if state is
consistently guarded by the same lock.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>