- Dec 09, 2011
-
-
Tony Breeds authored
The upcomming currituck patches will need to do 64-bit shifts which will fail with undefined symbol without this patch. I looked at linking against libgcc but we can't guarantee that libgcc was compiled with soft-float. Also Using ../lib/div64.S or ../kernel/misc_32.S, this will break the build as the .o's need to be built with different flags for the bootwrapper vs the kernel. So for now the easyest option is to just copy code from arch/powerpc/kernel/misc_32.S I don't think this code changes too often ;P Signed-off-by:
Tony Breeds <tony@bakeyournoodle.com> Signed-off-by:
Josh Boyer <jwboyer@gmail.com>
-
Christoph Egger authored
CONFIG_PPC47x doesn't exist in Kconfig and no 476 processor calls this function ppc44x_pin_tlb() as it has it's own ppc47x_pin_tlb(). This code is probably an artifact of the original 476 code that shouldn't have made it upstream. Signed-off-by:
Christoph Egger <siccegge@cs.fau.de> Signed-off-by:
-
Tony Breeds authored
Needed if you want to use swiotlb, harmless otherwise. Signed-off-by:
-
Tony Breeds authored
Currituck doesn't need nor use SDR so aborting the pci setup if there is no sdr-base would be bad. Add a flag to ppc4xx_pciex_hwops for the backends to state if they need SDR and then only complain and abort if they do and it's not found in the device tree. Signed-off-by:
-
Tony Breeds authored
Signed-off-by:
-
- Nov 30, 2011
-
-
Josh Boyer authored
Update the PowerPC 4xx git tree to a new location Signed-off-by: -
Tanmay Inamdar authored
The AppliedMicro APM8018X embedded processor targets embedded applications that require low power and a small footprint. It features a PowerPC 405 processor core built in a 65nm low-power CMOS process with a five-stage pipeline executing up to one instruction per cycle. The family has 128-kbytes of on-chip memory, a 128-bit local bus and on-chip DDR2 SDRAM controller with 16-bit interface. Signed-off-by:
Tanmay Inamdar <tinamdar@apm.com> Signed-off-by:
-
- Nov 28, 2011
-
-
Dan McGee authored
Since commit 8a0a9bd4, this comment in mmap_rnd() does not hold true as the value returned by get_random_int() will in fact be different every single call. Remove the comment and simplify the code back to its original desired form. This reverts commit a5adc91a which is no longer necessary and also fixes the sparc code that copied this same adjustment. Signed-off-by:
Dan McGee <dpmcgee@gmail.com> Acked-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org>
-
Anton Blanchard authored
During kdump stress testing I sometimes see the kdump kernel panic with: Interrupt 0x306 (real) is invalid, disabling it. Kernel panic - not syncing: bad return code EOI - rc = -4, value=ff000306 Instead of panicing print the error message, dump the stack the first time it happens and continue on. Add some more information to the debug messages as well. Signed-off-by:
Anton Blanchard <anton@samba.org> Signed-off-by:
-
Anton Blanchard authored
On a 64bit book3s machine I have an oops from a system reset that claims the book3e CE bit was set: MSR: 8000000000021032 <ME,CE,IR,DR> CR: 24004082 XER: 00000010 On a book3s machine system reset sets IBM bit 46 and 47 depending on the power saving mode. Separate the definitions by type and for completeness add the rest of the bits in. Signed-off-by:
-
Matthew McClintock authored
In lieu of having multiple similiar lines, we can just have one generic cpu-as line for CONFIG_ALTIVEC Signed-off-by: -
Dmitry Baryshkov authored
CPC925/CPC945 use special window to access host bridge functionality of u3-ht. Provide a way to access this device. Signed-off-by:
Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> Signed-off-by:
-
sukadev@linux.vnet.ibm.com authored
As described in the help text in the patch, this token restricts general access to /dev/mem as a way of increasing the security. Specifically, access to exclusive IOMEM and kernel RAM is denied unless CONFIG_STRICT_DEVMEM is set to 'n'. Implement the 'devmem_is_allowed()' interface for Powerpc. It will be called from range_is_allowed() when userpsace attempts to access /dev/mem. This patch is based on an earlier patch from Steve Best and with input from Paul Mackerras and Scott Wood. [BenH] Fixed a typo or two and removed the generic change which should be submitted as a separate patch Signed-off-by:Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com> Signed-off-by:
-
- Nov 25, 2011
-
-
Benjamin Herrenschmidt authored
-
Justin P. Mattock authored
The patch below removes an extra semicolon. Signed-off-by:
Justin P. Mattock <justinmattock@gmail.com> CC: linuxppc-dev@lists.ozlabs.org CC: Paul Mackerras <paulus@samba.org> Signed-off-by:
-
Ananth N Mavinakayanahalli authored
On Fri, Nov 11, 2011 at 10:17:55AM +0530, Ananth N Mavinakayanahalli wrote: > > > > At this rate we're going to end up with no bits left for CPU features > > way too quickly... Especially for something we only care about once at > > boot time. > > > > Wouldn't CPU_FTR_PPCAS_ARCH_V2 be a good enough test ? > > /me checks Cell manuals... yes, that test would be good enough. I will > cook up a patch to use this. Here it is... Signed-off-by: -
Benjamin Herrenschmidt authored
This adds support for p7IOC (and possibly other IODA v1 IO Hubs) using OPAL v2 interfaces. We completely take over resource assignment and assign them using an algorithm that hands out device BARs in a way that makes them fit in individual segments of the M32 window of the bridge, which enables us to assign individual PEs to devices and functions. The current implementation gives out a PE per functions on PCIe, and a PE for the entire bridge for PCIe to PCI-X bridges. This can be adjusted / fine tuned later. We also setup DMA resources (32-bit only for now) and MSIs (both 32-bit and 64-bit MSI are supported). The DMA allocation tries to divide the available 256M segments of the 32-bit DMA address space "fairly" among PEs. This is done using a "weight" heuristic which assigns less value to things like OHCI USB controllers than, for example SCSI RAID controllers. This algorithm will probably want some fine tuning for specific devices or device types. Signed-off-by: -
Benjamin Herrenschmidt authored
It advertises "host bridge" instead of "PCI to PCI bridge" which confuses the Linux probe code. Signed-off-by: -
Benjamin Herrenschmidt authored
This is used for newer IO Hubs such as p7IOC. Signed-off-by: -
Benjamin Herrenschmidt authored
When PCI_REASSIGN_ALL_RSRC is set, we used to clear all bus resources at the beginning of survey and re-allocate them later. This changes it so instead, during early fixup, we mark all resources as IORESOURCE_UNSET and move them down to be 0-based. Later, if bus resources are still unset at the beginning of the survey, then we clear them. This shouldn't impact the re-assignment case on 4xx, but will enable us to have the platform do some custom resource assignment before the survey, by clearing individual resources IORESOURCE_UNSET bit. Also limits the clutter in the kernel log from fixup when re-assigning since we don't care about the offset applied to the BAR values in this case. Signed-off-by: -
Benjamin Herrenschmidt authored
Some platforms need to perform resource allocation using a custom algorithm due to HW constraints, or may want to tweak things globally below a host bridge. For example OPAL support for IODA will need to perform a resource allocation pass that applies IODA specific segmentation constraints to MMIO which cannot be done simply using the kernel generic resource management code. Signed-off-by: -
Geoff Thorpe authored
This adds a pgprot combination required by some cache-enabled IO device mappings, such as Freescale datapath (QMan and BMan) portals. Signed-off-by:
Geoff Thorpe <geoff@geoffthorpe.net> Signed-off-by:
-
Thomas Gleixner authored
All interrupts which must be non threaded are marked IRQF_NO_THREAD. So it's safe to allow force threaded handlers. Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Thomas Gleixner authored
IPI handlers cannot be threaded. Remove the obsolete IRQF_DISABLED flag (see commit e58aa3d2) while at it. Signed-off-by:
-
Thomas Gleixner authored
Cascade handlers must run in hard interrupt context. Signed-off-by:
-
Thomas Gleixner authored
Cascade interrupt must run in hard interrupt context. Signed-off-by:
-
Ravi K. Nittala authored
The RTAS firmware flash update is conducted using an RTAS call that is serialized by lock_rtas() which uses spin_lock. While the flash is in progress, rtasd performs scan for any RTAS events that are generated by the system. rtasd keeps scanning for the RTAS events generated on the machine. This is performed via workqueue mechanism. The rtas_event_scan() also uses an RTAS call to scan the events, eventually trying to acquire the spin_lock before issuing the request. The flash update takes a while to complete and during this time, any other RTAS call has to wait. In this case, rtas_event_scan() waits for a long time on the spin_lock resulting in a soft lockup. Fix: Just before the flash update is performed, the queued rtas_event_scan() work item is cancelled from the work queue so that there is no other RTAS call issued while the flash is in progress. After the flash completes, the system reboots and the rtas_event_scan() is rescheduled. Signed-off-by:
Suzuki Poulose <suzuki@in.ibm.com> Signed-off-by:
Ravi Nittala <ravi.nittala@in.ibm.com> Reported-by:
Divya Vikas <divya.vikas@in.ibm.com> Signed-off-by:
-
Jimi Xenidis authored
This patch add the Chroma platform to WSP/PowerEN, which is a PCIe card (a defconfig is included). The card includes an H8 service processor that is used to manage the card. The H8 is connected over the second serial UART on the PowerEN chip so this patch includes a simple 16550 driver to enable communication, mostly for "power off" and "rebooting". This patch also includes a, WSP specific, "halt" method that will shut of all A2 cores but still leave power on at the chip level. This is desirable, especially if you wish to interrogate the chip with a hardware probe after the halt. Signed-off-by:
Jimi Xenidis <jimix@pobox.com> Signed-off-by:
-
Jimi Xenidis authored
Sorry, there was a typo in the #if signed-off-by:
-
Jimi Xenidis authored
The 'u' command will print the TLB on book3e parts and the SLB on Book3s parts, but the help system doesn't say that correctly. Signed-off-by:
-
Jimi Xenidis authored
This patch adds a fault handler that responds to illegal Coprocessor types. Currently all CTs are treated and illegal. There are two ways to report the fault back to the application. If the application used the record form ("icswx.") then the architected "reject" is emulated. If the application did not used the record form ("icswx") then it is selectable by config whether the failure is silent (as architected) or a SIGILL is generated. In all cases pr_warn() is used to log the bad CT. Signed-off-by: -
Jimi Xenidis authored
ICSWX is also used by the A2 processor to access coprocessors, although not all "chips" that contain A2s have coprocessors. Signed-off-by:
-
Jimi Xenidis authored
Some processors, like embedded, that already have a PID register that is managed by the system. This patch separates the ACOP and PID processing into separate files so that the ACOP code can be shared. Signed-off-by:
-
Florian Fainelli authored
libio.h is not provided by uClibc, in order to be able to test the definition of __UCLIBC__ we need to include stdlib.h, which also includes stddef.h, providing the definition of 'NULL'. Signed-off-by:
Florian Fainelli <florian@openwrt.org> Signed-off-by:
-
Julia Lawall authored
np is initialized to the result of calling a function that calls of_node_get, so of_node_put should be called before the pointer is dropped. The semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/ ) // <smpl> @@ expression e,e1,e2; @@ * e = \(of_find_node_by_type\|of_find_node_by_name\)(...) ... when != of_node_put(e) when != true e == NULL when != e2 = e e = e1 // </smpl> Signed-off-by:
Julia Lawall <julia@diku.dk> Signed-off-by:
-
Julia Lawall authored
np is initialized to the result of calling a function that calls of_node_get, so of_node_put should be called before the pointer is dropped. The semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/ ) // <smpl> @@ expression e,e1,e2; @@ * e = \(of_find_node_by_type\|of_find_node_by_name\)(...) ... when != of_node_put(e) when != true e == NULL when != e2 = e e = e1 // </smpl> Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Milton Miller authored
Some pseries IOMMUs cache TCEs but don't snoop when the TCEs are changed in memory, hence we need manually invalidate in software. This adds code to do the invalidate. It keys off a device tree property to say where the to do the MMIO for the invalidate and some information on what the format of the invalidate including some magic routing info. it_busno get overloaded with this magic routing info and it_index with the MMIO address for the invalidate command. This then gets hooked into the building and freeing of TCEs. This is only useful on bare metal pseries. pHyp takes care of this when virtualised. Based on patch from Milton with cleanups from Mikey. Signed-off-by:
Milton Miller <miltonm@bga.com> Signed-off-by:
Michael Neuling <mikey@neuling.org> Signed-off-by:
-
Anton Blanchard authored
decrementer_check_overflow is called from arch_local_irq_restore so we want to make it as light weight as possible. As such, turn decrementer_check_overflow into an inline function. To avoid a circular mess of includes, separate out the two components of struct decrementer_clock and keep the struct clock_event_device part local to time.c. The fast path improves from: arch_local_irq_restore 0: mflr r0 4: std r0,16(r1) 8: stdu r1,-112(r1) c: stb r3,578(r13) 10: cmpdi cr7,r3,0 14: beq- cr7,24 <.arch_local_irq_restore+0x24> ... 24: addi r1,r1,112 28: ld r0,16(r1) 2c: mtlr r0 30: blr to: arch_local_irq_restore 0: std r30,-16(r1) 4: ld r30,0(r2) 8: stb r3,578(r13) c: cmpdi cr7,r3,0 10: beq- cr7,6c <.arch_local_irq_restore+0x6c> ... 6c: ld r30,-16(r1) 70: blr Unfortunately we still setup a local TOC (due to -mminimal-toc). Yet another sign we should be moving to -mcmodel=medium. Signed-off-by: -
Anton Blanchard authored
Fix some formatting issues and use the DECREMENTER_MAX define instead of 0x7fffffff. Signed-off-by:
-
Anton Blanchard authored
The clockevents code uses max_delta_ns to avoid calling a clockevent with too large a value. Remove the redundant version of this in the timer_interrupt code. Signed-off-by:
-
